Characterization of Turkish Olive Oils by Triacylglycerol Structures and Sterol Profiles

A characterization study of Turkish monovarietal olive oils using chemical variables such as fatty acid, sn‐2 fatty acid, triacylglycerol, and sterol composition is presented. A total of 101 samples of Olea europaea L. fruits from 18 cultivars were collected for two crop years from west, south, and southeast regions of Turkey. Olives were processed to oil and olive oil samples were evaluated for their triacylglycerol structures and sterol composition. Oleic acid content ranged from 60.15 to 80.46 % of total fatty acids and represented 70.90–89.02 % of sn‐2 position triacylglycerols. Major triglycerides of oil samples were triolein, palmitodiolein, dioleolinolein, palmitooleolinolein, dipalmitoolein, and stearodiolein. Triolein values were between 24.72 and 48.64 % and compatible with the fatty acid composition. Total sterol content varied from 1,145.32 to 2,211.77 mg/kg and Edremit yagl?k stood out because of its high sterol content. A one‐way analysis of variance revealed significant differences for variables among cultivars. Principle component analysis enabled the classification of common varieties on the basis of analytical data. Sterol composition achieved more relevant discrimination than fatty acid and triglyceride composition. Classification according to geographical origin was performed by discriminant analysis.     

Influence of preparation conditions on porous structures of olive stone activated by H3PO4

An olive factory residue was used as a precursor in the preparation of granular activated carbon by chemical activation with H₃PO₄. Effects of final activation temperature, time, and H₃PO₄ concentration used in the impregnation stage on the porous development were investigated. SO₂ adsorption experiments were also performed for some of the activated carbon samples to represent their adsorption performance. Activation at low temperature represented that micropores were developed first at early stages of the temperatures. Mesoporosity developed at around 250 °C, enhanced up to 400 °C, and then started to decrease due to possibly shrinking of pores. The optimum temperature for olive stone was found to be around 400 °C on the basis of total pore volume and BET surface area. It was clearly demonstrated that H₃PO₄ concentration used in the impregnation stage was not only effective for development of surface area and pore volumes but also an effective tool for tailoring the pore structure and size distribution.     

Poly(vinylbenzylchloride) beads grafted with polymer brushes carrying hydrazine ligand for reversible enzyme immobilization

Poly(glycidylmethacrylate), p(GMA), brush grafted poly(vinylbenzyl chloride/ethyleneglycol dimethacrylate), p(VBC/EGDMA), beads were prepared by suspension polymerization and the beads were grafted with poly(glycidyl methacrylate), p(GMA), via surface‐initiated atom transfer radical polymerization aiming to construct a material surface with fibrous polymer. The epoxy groups of the fibrous polymer were reacted with hydrazine (HDZ) to create affinity binding site on the support for adsorption of protein. The influence of pH, and initial invertase concentration on the immobilization capacity of the p(VBC/EGDMA‐g‐GMA)‐HDZ beads has been investigated. Maximum invertase immobilization onto hydrazine functionalized beads was found to be 86.7 mg/g at pH 4.0. The experimental equilibrium data obtained invertase adsorption onto p(VBC/EGDMA‐g‐GMA)‐HDZ affinity beads fitted well to the Langmuir isotherm model. It was shown that the relative activity of immobilized invertase was higher than that of the free enzyme over broader pH and temperature ranges. The K_m and V_max values of the immobilized invertase were larger than those of the free enzyme. After inactivation of enzyme, p(VBC/EGDMA‐g‐GMA)‐HDZ beads can be easily regenerated and reloaded with the enzyme for repeated use. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Sub-nanomolar sensing of ionic mercury with polymeric electrospun nanofibers

Ethyl cellulose (EC) based electrospun nanofibers were exploited for sub-nanomolar level optical chemical sensing of ionic mercury. An azomethine ionophore was used as Hg (I) and Hg (II) sensing material. Ethyl cellulose nanofibers with varying amounts of the ionic liquid; 1-ethyl-3-methylimidazolium tetrafluoroborate (EMIMBF₄) were prepared and characterized. The nanofibers were fabricated by electrospinning technique. The offered chemosensor allow determination of mercury ions in a large linear working range between 1.0 × 10⁻¹⁰ and 1.0 × 10⁻⁴ mol L⁻¹. Limit of detection was found to be 0.07 nM which makes this technique alternative to cold-vapor atomic absorption spectrometry (CV-AAS), flame emission methods and to inductively coupled plasma-mass spectrometry (ICP-MS).     

A solution state diode using semiconductor polymer nanorods with nanogap electrodes

A solution state polymer diode, which uses regioregular poly(3-hexylthiophene-2,5-diyl) (P3HT):dichlorobenzene solution as the semiconductor between highly doped p-type silicon and aluminum electrodes has been built. Electrodes separated by a 40 nm gap enable intra-chain charge carrier transfer through the lengths of single polymer chains. This prevents chain to chain hopping and chain entanglements, increasing carrier mobility. The degradation with time and hysteresis effects of the diodes are measured. An optimal P3HT solution concentration of 6 mg ml(-1) is found. A current density of at least 300 mA cm(-2) is achieved, indicating at least a six-fold improvement in carrier mobility compared to previously fabricated solid state P3HT diodes.     

Double Threshold Energy Based Spectrum Sensing with Copulas

Wireless Personal Communications - As it is known, Energy based detection is widely used in Cognitive Radio and radar systems. In order to reduce the disruptive effects of wireless channels, Energy...     

The use of polyaniline films on flexible tape for supercapacitor applications

A sticky surface of a tape was adhered to a graphite surface and then the tape was peeled off. The insulator tape was coated with thin graphite and became conductive in order to use flexible tape as a current collector. Aniline was electrodeposited onto a flexible tape substrate having graphite layer by electrochemical polymerization method from an aqueous (H₂SO₄ solution containing aniline monomers) and non-aqueous media (a deep eutectic solvent containing aniline). The prepared polymeric electrodes were characterized by Fourier transform infrared spectroscopy, Raman, thermogravimetric analysis and scanning electron microscopy techniques. The electrochemical properties of coated and uncoated electrodes were also examined by cyclic voltammetry and galvanostatic charge discharge techniques. The polyaniline (PANI) coated tape can be used as a flexible electrode in supercapacitor applications because PANI coated electrodes are highly electroactive in Na₂SO₄ electrolyte. After 3000 cycles, the capacitance retention of PANI film electrodeposited from Ethaline bath was 90%, while the areal capacitance of PANI film obtained from acidic medium reaches 50% after 500 cycles. As PANI electrode is stable in an ionic liquid for long cycling, Ethaline ionic liquid can be used as electrolyte for PANI based supercapacitor electrode. PANI coated graphite on tape, which is prepared in an easy and inexpensive way is a promising flexible material for high performance supercapacitors.     

Landfill Settlement with Decomposition and Gas Generation

A one-dimensional multiphase numerical model is developed to simulate the vertical settlement involving liquid and gas flows in a deformable (settling) municipal solid waste (MSW) landfill. MSW is represented by a chemical composition, and a global stoichiometric reaction is used to estimate the maximum yield of gas generation. Following the general assumption accepted in the literature, the gas generated by waste decomposition is assumed to comprise of methane (CH4) and carbon dioxide (CO2). The gas generation rate follows an exponentially decaying function of time. The gas generation model developed based on a first-order kinetic single-bioreactor approach includes the governing equations of gas migration, liquid flow, and landfill deformation. The Galerkin finite element method is used to solve the resulting equations. The model developed can be used to estimate the transient and ultimate settlements due to waste decomposition and gas generation in MSW landfills. The proposed model can estimate the waste porosity, gas pressure, liquid pressure, gas saturation, liquid saturation, and stress distributions in settling landfills. The results obtained for a deformable landfill are compared with a landfill having a rigid solid skeleton. Due to settlement, the depth of waste is 27% smaller in deformable landfills than that of the rigid ones.