金属铝诱导法低温制备多晶硅薄膜

以氢气稀释的硅烷（SiH4）和硼烷（B2H6）为气源,利用等离子体增强化学气相沉积法（PECVD）制备出p型a-Si薄膜.采用铝诱导晶化技术对不同厚度的铝膜对a-Si薄膜晶化的影响进行了研究.实验中发现,铝膜溅射为10 s的非晶硅薄膜样品在450℃下退火10 min后,p型a-Si结构仍为非晶态,铝膜溅射为20 s的非晶硅薄膜在450℃下退火20 min后,p型a-Si薄膜开始晶化为polySi薄膜,并且铝膜厚度越厚,则a-Si薄膜晶化程度越强.     

Viscoelastic Behavior, Thermodynamic Compatibility, and Phase Equilibria in Block Copolymer-Based Pressure-Sensitive Adhesives

The viscoelastic behavior, thermodynamic compatibility, and phase equilibria in block copolymer-based pressure-sensitive adhesives were investigated. The block copolymers investigated were: (1) polystyrene-block-polybutadiene-block-polystyrene (SBS) copolymer (KRATON® D-1102, Shell Development Company) and (2) polystyrene-block-polyisoprene-block-polystyrene (SIS) copolymer (KRATON® D-1107, Shell Development Company). The tackifying resins investigated were: (1) WINGTACK® 86 (Goodyear Tire & Rubber Company) and (2) PICCOTAC® 95BHT (Hercules Inc.). Samples of various compositions were prepared by a solution-casting method with toluene as solvent. Measurements of dynamic storage modulus (G'), dynamic loss modulus (G'), and loss tangent (tan δ) were taken, using a Rheometrics Mechanical Spectrometer. It was found that: (1) both WINGTACK 86 and PICCOTAC 95BHT were equally effective in decreasing the plateau modulus (G^O_N), and increasing the glass transition temperature (T_g) of the polyisoprene midblock of KRATON 1107; and (2) WINGTACK 86 was very effective in decreasing the G^O_N and increasing the T_g of the polybutadiene midblock of KRATON 1102, whereas PICCOTAC 95BHT was not. The observed difference between WINGTACK 86 and PICCOTAC 95BHT in decreasing the G^O_N and increasing the T_g of the polybutadiene midblock of KRATON 1102, whereas PICCOTAC 95BHT was not. The observed difference between WINGTACK 86 and PICCOTAC 95BHT in decreasing the G^O_N and increasing the T_g of the polybutadiene midblock of KRATON 1102 (perhaps to SBS block copolymers in general) is explained by the values of the interaction parameter for WINGTACK 86 and KRATON 1102, and for PICCOTAC 95BHT and KRATON 1102. The interaction parameter was determined, using the piezoelectric quartz sorption method. Phase diagrams were constructed for the four block copolymer/tackifying resin systems investigated, using information obtained from both dynamic viscoelastic measurements and optical microscopy. It was found that when mixed with KRATON 1102, PICCOTAC 95BHT formed separate domains whereas WINGTACK 86 did not over the range of concentrations and temperatures investigated. This confirms the evidence obtained from two other independent experimental techniques, namely, dynamic viscoelastic measurements and the piezo-electric sorption method. We have concluded from the present study that PICCOTAC 95BHT is not as an effective tackifying resin as WINGTACK 86, when each is mixed with KRATON 1102. It is pointed out further that information on the order-disorder transition temperature T_r, which was determined from a rheological technique proposed by us, is valuable in determining optimal processing conditions for block copolymer-based pressure-sensitive adhesives.     

Effects of soaking soybeans in dilute acids on biologically active components

Soaking soybeans in dilute acids affected activities of lipoxygenase, trypsin inhibitor and urease. Effects of soaking time, acid concentration and soaking temperature were investigated. Lipoxygenase activity was completely eliminated by soaking in 0.3 M HC1 at either 23°C or 40°C for 8 hr. Less than 50% trypsin inhibitor remained and urease was inactivated to an acceptable level (0.04 ΔpH).     

Near-duplicate document image matching: A graphical perspective

A near-duplicate document image matching approach characterized by a graphical perspective is proposed in this paper. Document images are represented by graphs whose nodes correspond to the objects in the images. Consequently, the image matching problem is then converted to graph matching. To deal with the instability of object segmentation, a multi-granularity object tree is constructed for a document image. Each level in the tree corresponds to one possible object segmentation, while different levels are characterized by various object granularities. Some graphs can be generated from the tree and the objects associated with each graph may be of different granularities. Two graphs with the maximum similarity are found from the multi-granularity object trees of the two near-duplicate document images which are to be matched. The encouraging experimental results have demonstrated the effectiveness of the proposed approach.     

Conceptual and basic designs of the Mobile Harbor crane based on topology and shape optimization

The Mobile Harbor (MH) has been recently proposed as a novel maritime cargo transfer system that can move to a container ship anchored in the deep sea and handle containers directly at sea with the aid of a stabilized MH crane. Because this system operates under at-sea conditions, the MH crane must be designed to support an inertia load and wind force, as well as its self-weight. The wave-induced motions of the MH, e.g. rolling, pitching, and heaving, generate a significant amount of inertia load, which has not been considered in the design of conventional quayside cranes installed on stable ground. Wind force is also a critical design factor due to the higher wind velocity in the open sea. In addition to the aforementioned structural rigidity, mass minimization is also important in the structural design of MH cranes because it reduces the overturning moment and therefore enhances ship stability. In this paper, the sensitivities of the design-dependent loads (i.e. self-weight, inertia load, and wind force) are derived with respect to the design variables, and then a topology optimization is conducted with the derived sensitivities in order to obtain a conceptual design. Then, the conceptual design is elaborated into a three-dimensional basic design through shape optimization with design regulations for offshore cranes. Through the integrated design process with the topology and shape optimizations, a conceptual and basic design is successfully obtained for the MH crane.     

Characterization of poly(vinylidenefluoride-co-hexafluoropropylene)-based polymer electrolyte filled with TiO2 nanoparticles

Nanoscale TiO₂ particle filled poly(vinylidenefluoride-co-hexafluoropropylene) film is characterized by investigating some properties such as surface morphology, thermal and crystalline properties, swelling behavior after absorbing electrolyte solution, chemical and electrochemical stabilities, ionic conductivity, and compatibility with lithium electrode. Decent self-supporting polymer electrolyte film can be obtained at the range of <50 wt% TiO₂. Different optimal TiO₂ contents showing maximum liquid uptake may exist by adopting other electrolyte solution. Room temperature ionic conductivity of the polymer electrolyte placed surely on the region of >10⁻³ S/cm, and thus the film is very applicable to rechargeable lithium batteries. An emphasis is also be paid on that much lower interfacial resistance between the polymer electrolyte and lithium metal electrode can be obtained by the solid-solvent role of nanoscale TiO₂ filler.     

模型驱动的装备保障优化决策支持系统

以数据、模型、用户界面等要素为基础,提出了以优化模型为驱动的装备保障优化决策支持系统设计思路,拓展设计了系统总体功能结构.构建了包含算法库、模型库和应用库的模型库,引入了脚本模型,以顺序、选择或循环结构程序组合优化模型,实现复杂装备保障决策问题的求解和决策.实例应用表明系统极大地提高了部队装备精确保障能力.     

无线环境下基于多流优先级的并行多路传输

在无线异构网络环境下提出一种基于多流优先级的并行多路传输方案。该方案基于并行多路传输协议CMT-SCTP,并利用了SCTP的多流特性和部分可靠特性。针对数据的重要性和时间敏感度,设计优先级数据调度算法;同时提出基于路径质量的数据分发机制,进一步保证数据的有效传输。在NS-2中的仿真结果表明,该方案能够有效提高数据传输的吞吐量,减少时延,保证较好的数据传输性能。     

Improved activity and thermostability of Candida antarctica lipase B by DNA family shuffling

DNA family shuffling was used to create chimeric lipase B proteins with improved activity toward the hydrolysis of diethyl 3-(3',4'-dichlorophenyl)glutarate (DDG). Three homologous lipases from Candida antarctica ATCC 32657, Hyphozyma sp. CBS 648.91 and Crytococcus tsukubaensis ATCC 24555 were cloned and shuffled to generate a diverse gene library. A high-throughput screening assay was developed and used successfully to identify chimeric lipase B proteins having a 20-fold higher activity toward DDG than lipase B from C.antarctica ATCC 32657 and a 13-fold higher activity than the most active parent derived from C.tsukubaensis ATCC 24555. In addition, the stability characteristics of several highly active chimeric proteins were also improved as a result of family shuffling. For example, the half-life at 45 degrees C and melting point (T(m)) of one chimera exceeded those of lipase B from C.antarctica ATCC 32657 by 11-fold and 6.4 degrees C, respectively, which closely approached the stability characteristics of the most thermostable parent derived from Hyphozyma sp. CBS 648.91.     

Multi‐surface sliding control for fast finite‐time leader–follower consensus with high order SISO uncertain nonlinear agents

In this paper, multi surface sliding cooperative control scheme is presented and new multiple sliding surfaces are proposed. It is proven that, for the setup that each agent is described by a chain of integrators, where the last integrator is perturbed by a bounded disturbance, leader–follower consensus can be achieved on these sliding surfaces if the communication graph has a directed spanning tree. Also, sliding variables can be driven to the sliding surfaces in fast finite time by the nonsmooth control law. The fast finite‐time Lyapunov stability theorem, the terminal sliding control technique, and the adding a power integrator design approach are used in our proposed control. Simulation results demonstrate the effectiveness of the proposed scheme. Copyright © 2013 John Wiley & Sons, Ltd.