Efficient PL Emission from p-type Porous Silicon: A Comparative Study for Selection of Effective Anodization Parameters

The physical mechanism of highly efficient photoluminescence (PL) emission from p-type silicon is described by a comparative study of the effectiveness of the etching parameters in an electrochemical anodization technique. Two series of porous silicon samples were prepared in a combination of anodization current and time, to maintain the total amount of anodic charge transfer constant. Photoluminescence studies show that irrespective of the amount of charge transfer, the samples prepared with comparatively higher current density show an efficient PL as well as stronger blueshift in the emission energy vis-à-vis the samples prepared for longer durations. An overall decrease in crystallite size, as estimated by Raman spectral analysis, was observed for both series of samples with the progress of charge transfer. Comparative analysis shows a marginal difference in crystallite size for both series of samples in the initial state of charge transfer, whereas major differences arise at higher values. This is explained with the formation of silicon suboxide on the porous surface at higher current density, leading to initiation of side wall reaction, and higher reduction rate in crystallite size as well as strong luminescence due to the carrier quantum confinement effect.     

Effects of Cooling Rate and Component on the Microstructure and Mechanical Properties of Mg–Zn–Y Alloys

The microstructure and mechanical properties of Mg–6Zn–1Y and Mg–6Zn–3Y(wt%) alloys under different cooling rates were investigated. The results show that the second dendrite arm spacing(SDAS) of Mg–6Zn–1Y and Mg–6Zn–3Y is reduced by 32 and 30% with increasing cooling rates(Rc) from 10.2 to 23 K/s, which can be predicted using a empirical model of SDAS=68 R 0:45:45cand SDAS=73 R 0c, respectively. The compressive strength of both alloys increases with increasing the cooling rate, which is attributed to the increase of volume fraction(Vf) of secondary phases under high cooling rate. The interaction of the cooling rate and component with SDAS has been theoretically analyzed using interdependence theory.     

可调偏迈步式胶带自移机尾的研究

随着掘进工作面自动化程度的提高,掘进巷道速度也在日益加快,而现有的顺槽皮带机机尾移动缓慢且移动时工作量大,需要两三人配合操作,存在一定的安全隐患。针对以上问题,研发可调偏迈步式胶带自移机尾,具有与悬挂二运皮带转载机搭接行程长,可以迈步式前进,自动调偏等功能,同时,可以降低工人的劳动强度,加快巷道掘进速度。     

视频侦查中人像智能分析应用及算法优化

人像智能分析指的是对视频或录像中的人像进行结构化和可视化分析,对目标人物进行性别、年龄、发型等特征的智能识别,这项技术在视频侦查中有极高的应用价值。人像识别早期的算法是通过人工提取特征,通过学习低级视觉特征来针对不同属性进行分类学习,这种基于传统方法的模型表现常常不尽如人意。在计算机视觉领域,通过海量图像数据学习的神经网络比传统方法有更丰富的信息量和特征可以被提取。文章尝试通过深度学习技术训练神经网络模型对行人进行检测和识别,对于衣着不同的行人进行智能识别,具有更好的鲁棒性,提升了视频人像识别的准确率,拓展了人工智能技术在身份识别领域的应用。     

Matrix Transformation in Boron Containing High-Temperature Co–Re–Cr Alloys

An addition of boron largely increases the ductility in polycrystalline high-temperature Co–Re alloys. Therefore, the effect of boron on the alloy structural characteristics is of high importance for the stability of the matrix at operational temperatures. Volume fractions of ε (hexagonal close-packed—hcp), γ (face-centered cubic—fcc) and σ (Cr₂Re₃ type) phases were measured at ambient and high temperatures (up to 1500 °C) for a boron-containing Co–17Re–23Cr alloy using neutron diffraction. The matrix phase undergoes an allotropic transformation from ε to γ structure at high temperatures, similar to pure cobalt and to the previously investigated, more complex Co–17Re–23Cr–1.2Ta–2.6C alloy. It was determined in this study that the transformation temperature depends on the boron content (0–1000 wt. ppm). Nevertheless, the transformation temperature did not change monotonically with the increase in the boron content but reached a minimum at approximately 200 ppm of boron. A probable reason is the interplay between the amount of boron in the matrix and the amount of σ phase, which binds hcp-stabilizing elements (Cr and Re). Moreover, borides were identified in alloys with high boron content.     

Effects of hydrolysis of precursor on the structures and properties of polymer-derived SiBN ceramic fibers

In this paper, polyborosilazane precursor was synthesied from HMDZ, HSiCl₃, BCl₃ and CH₃NH₂ using a multistep method. By controlling the storage conditions, parts of the polyborosilazane fibers were hydrolyzed. FT-IR, NMR, XRD, TEM and monofilament tensile strength test were employed to study the effects of hydrolysis of precursor on the structures and properties of polymer-derived SiBN ceramic fibers. FT-IR and NMR results indicate that Si-N group in PBSZ reacts with H₂O to form Si-O-Si group. After pyrolysis reaction at 1400℃, Si-O-Si group will finally transformed into highly ordered cristobalite and β-quartz, resulting in formation of the wrinkled surface of the obtained SiBN ceramic fiber. The strip-like defects on fiber surface, according to monofilament tensile strength test, had a significant effect on mechanical property of the obtained SiBN ceramic fiber and caused no increase in fiber tensile strength of hydrolytic polyborosilazane fiber before and after pyrolytic process.     

丙烷脱沥青装置调合前沥青的综合利用

在丙烷脱沥青装置加热炉试烧装置自产调合前沥青,通过观察油枪雾化沥青的能力、火嘴的燃烧情况以及燃烧后的烟尘状况,筛选出适合沥青燃烧的油枪,最终实现调合前沥青直接做加热炉燃料、减少重油出厂量的目的。     

Imaging of two-dimensional unsaturated moisture flows in uncracked and cracked cement-based materials using electrical capacitance tomography

The development of visualizing tools to monitor unsaturated moisture flow in cement-based materials is of great importance, as most degradation processes in cement-based materials are connected to and take place in the presence moisture. This paper investigates the ability of electrical capacitance tomography (ECT) to image two-dimensional (2D) unsaturated moisture flow in cement-based materials. In ECT, the electrical permittivity distribution within an object is reconstructed based on measured capacitances between electrodes attached on the object’s surface. In a series of experiments, mortar specimens with and without discrete cracks were imaged with ECT during a 2D moisture ingress. The results show that ECT is able to monitor the evolution of the moisture flow, and to approximate the shape and position of the moisture front. These findings indicate that ECT is a viable method for monitoring and visualizing 2D unsaturated moisture flow in cement-based materials in the presence and absence of discrete cracks.     

Appraisal of Agriglass in Promoting Maize Production Under Abiotic Stress Conditions

An agriglass composition containing different oxides acts as a slow release for macro and micro nutrients and was chosen to improve maize yield under most important abiotic stresses which affecting agriculture development; salinity and drought. A field experiment was performed in salt affected soil (EC =?7.5 dSm^??1) by using different water deficit rates (I1 = 100, I2 = 85 and I3 = 70% of maize water requirements). Irrigation levels were located in main plots. Every main-plot divided into six sub-plots contained glassy fertilizer treatments [F1 = 55 kg fed^?1 with 1/2 mm diameter of agriglass (fed. =?4200 m²), F2 = 55 kg fed^?1 with 1 mm diameter, F3 = 80 kg fed^?1 with 1/2 mm diameter, F4 = 80 kg fed^?1 with 1 mm diameter, F5 = Recommendations of Ministry of Agriculture and F6 = control]. The experimental results demonstrated that, ears, straw, grains and biological yields increased with increasing both water and agriglass rates. Application of agriglass as a slow release fertilizer improved yield more than mineral fertilizer. Some growth parameters, water use efficiency (IWUE), macronutrients concentration and their relations were included. Other studies on residual effect of agriglass and the annual application rates to withstand salinity and drought stress by strategic crops are required.