Effects of Cooling Rate and Component on the Microstructure and Mechanical Properties of Mg–Zn–Y Alloys

The microstructure and mechanical properties of Mg–6Zn–1Y and Mg–6Zn–3Y(wt%) alloys under different cooling rates were investigated. The results show that the second dendrite arm spacing(SDAS) of Mg–6Zn–1Y and Mg–6Zn–3Y is reduced by 32 and 30% with increasing cooling rates(Rc) from 10.2 to 23 K/s, which can be predicted using a empirical model of SDAS=68 R 0:45:45cand SDAS=73 R 0c, respectively. The compressive strength of both alloys increases with increasing the cooling rate, which is attributed to the increase of volume fraction(Vf) of secondary phases under high cooling rate. The interaction of the cooling rate and component with SDAS has been theoretically analyzed using interdependence theory.     

Effects of hydrolysis of precursor on the structures and properties of polymer-derived SiBN ceramic fibers

In this paper, polyborosilazane precursor was synthesied from HMDZ, HSiCl₃, BCl₃ and CH₃NH₂ using a multistep method. By controlling the storage conditions, parts of the polyborosilazane fibers were hydrolyzed. FT-IR, NMR, XRD, TEM and monofilament tensile strength test were employed to study the effects of hydrolysis of precursor on the structures and properties of polymer-derived SiBN ceramic fibers. FT-IR and NMR results indicate that Si-N group in PBSZ reacts with H₂O to form Si-O-Si group. After pyrolysis reaction at 1400℃, Si-O-Si group will finally transformed into highly ordered cristobalite and β-quartz, resulting in formation of the wrinkled surface of the obtained SiBN ceramic fiber. The strip-like defects on fiber surface, according to monofilament tensile strength test, had a significant effect on mechanical property of the obtained SiBN ceramic fiber and caused no increase in fiber tensile strength of hydrolytic polyborosilazane fiber before and after pyrolytic process.     

DP980+Z烘烤硬化值与退火温度的关系

摘要：为了研究退火温度对镀锌DP980+Z烘烤硬化值的影响，退火温度控制在760～820℃之间，系统分析退火温度对烘烤硬化值的影响。通过准静态拉伸试验机测量烘烤硬化值及抗拉强度，采用lepara试剂对组织中的马氏体进行着色，利用金相显微镜及图像处理软件测量马氏体的体积分数；采用扫描电镜观察DP980+Z的双相组织特点，并且将组织图片通过CAD转化成有限元图进行网格划分，建立代表性体积单元（RVE），通过有限元分析铁素体、马氏体强度对烘烤硬化值的影响。在同样的变形量情况下，DP980+Z的原始屈服强度越高，烘烤硬化值越高。     

Zinc doped Fe2O3 for boosting Electrocatalytic Nitrogen Fixation to ammonia under mild conditions

Artificial nitrogen fixation is emerging as a promising approach for synthesis of ammonia at mild conditions. Inspired by biological nitrogen fixation based on bacteria containing iron, zinc doped Fe₂O₃ nanoparticles are proposed as an efficient and earth abundant electrocatalyst for converting N₂ to NH₃. In neutral media, it achieves a maximum Faradaic efficiency (FE) of 10.4% and a large NH₃ yield rate of 15.1 μg h^?1 mg^?1_cat. at ?0.5 V vs. reversible hydrogen electrode. This catalyst also exhibits excellent selectivity and stability. Theoretical calculations suggest the reaction follows the associative enzymatic mechanism and it has a barrier of as low as 0.68 eV.     

稠油微生物开采技术现状及进展

综述了用微生物方法开采稠油的技术现状与进展，论题如下。①概述。②基本方法：异源微生物采油，包括微生物吞吐和微生物驱；本源微生物采油压大港孔店油田的实例。③主要机理，包括产表面活性剂，降解稠油中重质组分及其他。④技术研究，包括机理性、可行性及经济效益研究，列举了国内外6个实例。⑤现场应用，包括国外1个、国内6个实例。⑥该技术的优势及问题。参22。     

感知与真实——2006大屏幕电视机产业焦点1080p和微显技术

通常，价值是感觉的一个重要指标，举个例子，很多人都愿意为一顿在别具特色餐厅中进行的牛扒午餐而挥洒不菲的金钱，这帮高素质的人都不会去关心这块与其它地方同样的牛扒是否真值那么多钱。     

铌和钨对γ-TiAl基合金热稳定性的影响

采用光学显微镜(OM)，扫描电镜(SEM)，X射线衍射研究了TiAl—5Nb，TiAl—14．3Nb，TiAl—8Nb—1W，TiAl—12．3Nb-2W四种合金片层组织在1000℃的热稳定性。结果表明，TiAl—12．3Nb-2W合金热稳定性最好，但合金元素对TiAl基合金热稳定性的影响机理还有待进一步的研究。