New approach to enhance adhesions between carbon nanotube emitters and substrate by the combination of electrophoresis and successive electroplating

Complementary electroplating combined with electrophoresis enhanced the field emission characteristics of emitters by improving the adhesions between CNT emitters and substrate. The emitting current of the CNT emitters prepared by our combined method increased nine times higher than that of CNT emitters prepared by electrophoresis only, since electroplating improved the adhesion of CNT emitters. During the life-time measurement for 10 h, the emitting current of CNT emitters fabricated by electrophoresis only was drastically decreased to 13% of the initial current, while that prepared by the combination of electrophoresis and successive electroplating decreased to 64% of the initial current. We suggest that our method is a promising approach for the efficient fabrication of reliable CNT emitters.     

Hydrothermal Synthesis of Magnesium Aluminate Platelets

Magnesium aluminate (MgAl₂O₄) platelets were first synthesized by hydrothermal treatment of γ-AlO(OH) in a magnesium nitrate aqueous solution at 400°C. The platelets are 100–200 nm in width and 25 nm in thickness. The influence of temperature, the anions of the magnesium salt, the amount of magnesium salt, and precursor pH on the formation of such structure was investigated. The experimental results indicated that the anions of the magnesium salt and precursor pH could have a significant influence on the growth of MgAl₂O₄. MgAl₂O₄ formation followed the in situ transformation mechanism, which was the reason why the MgAl₂O₄ crystallites had a platelet morphology.     

Effects of tube rupture modeling and the parameters on the analysis of multiple steam generator tube rupture event progression in APR1400

A multiple steam generator tube rupture (MSGTR) event in APR1400 has been investigated using the best estimate thermal hydraulic system code, MARS1.4. The effects of the parameters such as the number of ruptured tubes, rupture location, affected steam generator on the analysis of the MSGTR event in APR1400 are examined. In particular, tube rupture modeling methods, single tube modeling (STM) and double tube modeling (DTM), are compared. The APR1400 is found to have the capability of allowing more than 30 min to operators for the MSGTR event of five tubes. The effects of rupture location on the MSSV lift time is not significant in the case of STM, but the MSSV lift time for tube-top rupture is found to be 25.3% larger than that for rupture at the hot-leg side tube sheet in the case of DTM. The MSSV lift time for the cases that both steam generators are affected (4C5x, 4C23x) are found to be larger than that of the single steam generator cases (4A5x, 4B5x) due to a bifurcation of the primary leak flow. The discharge coefficient of Cd is found to affect the MSSV lift time only for a smaller value of 0.5. It is found that the most dominant parameter governing the MSSV lift time is the leak flow rate. Whether any modeling method is used, it gives the similar MSSV lift time if the leak flow rate is close, except in the case where both steam generators are affected. Therefore, the system performance and the MSSV lift time of the APR1400 are strongly dependent on the break flow model used in the best estimate system code.     

Al2O3对唐钢高炉炉渣性能的影响

针对唐钢近2年提高进口矿配比后，Al2O3含量升高对炉渣流动性带来的不利影响，对唐钢高炉的炉渣性能进行了试验研究。并结合国内同行业的生产实践经验，从理论上分析了炉渣中Al2O3及MgO的适宜含量范围，着重论述了唐钢所处冀东矿区条件下降低Al2O3的主要途径及适应高Al2O3炉渣的具体措施。     

外浮顶油罐的液位检测仪表选型及安装

音叉式液位开关和外贴超声波液位开关具有多种优点，近年来逐步取代浮球液位开关，成为大型储罐液位检测的重要仪表。本文通过详细介绍这两种液位开关在外浮顶油罐的设计选型和具体安装，通过阐述检测原理，比较各种安装方式的优缺点，分析产生缺陷的原因以及提出解决方法，为设计施工人员进行仪表选型和安装提供重要参考意见。     

飞行人员骨密度与内分泌调节关系的探讨

对37名骨密度(BD)低下的飞行员(实验组)和BD正常的48名飞行员、100名地面人员(正常对照组)进行了BD和血清TT_3、TT_4、TSH IRMA、CT、PTH、E_2和T放射免疫测定。结果显示,实验组BD均值明显低于对照组(p<0.01),血清TT_3、TT_4、CT、E_2(女性)和T(男性)均值与对照组比较,大多数年龄存在着显著或非常显著差异(p<0.05或p<0.01)。同时对飞行人员BD与几种内分泌激素关系进行了探讨。     

旋转式伽玛刀的辐射剂量学

旋转式伽玛刀的辐射剂量学指标的物理测试在放射性医疗设备投放医院正式临床使用前是必不可少的，是对设备及其附件的设计、加工制造、安装以及电气控制系统等的全面综合性检定。用电离室作辐射剂量学的绝对测量，用胶片法进行相对测量，给出了测量结果并进行了讨论。     

浸胶工艺对Nomex蜂窝性能的影响

本文研究了浸胶工艺对Ｎｏｍｅｘ蜂窝性能的影响，分析探讨了提高Ｎｏｍｅｘ蜂窝性能及外观质量的途径。研究结果表明：采取新的浸胶工艺制作的Ｎｏｍｅｘ蜂窝，各项性能全面达到法国宇航材料标准。