Identification of microstructural zones and thermal cycles in a weldment of modified 9Cr-1Mo steel

This paper presents the results of a study on the microstructural and microchemical variations in a multipass Gas Tungsten Arc weld (GTAW) of modified 9Cr-1Mo steel. The changes brought about in the steel due to the heating and cooling cycles during welding and the subsequent effects due to reheating effects during multipass welding are described. Detailed analytical transmission electron microscopy has been carried to study the type and composition of the primary and secondary phases in this steel. The systematic changes in microstructural parameters such as Prior Austenite Grain Size, martensite lath size, number density, size and microchemistry of carbides, have been understood based on the different transformations that the steel undergoes during the heating and cooling process. Based on the observed microstructure, an attempt has been made to identify distinct microstructural zones and possible thermal cycles experienced by different regions of the weldment.     

Effect of preparation technique on the properties of Mo-containing Al-MCM-41

The Al-MCM-41 has been used as support to prepare Mo-containing catalysts. The 12- molybdophosphoric heteropoly acid (HPMo) is used as initial compound. The catalysts are synthesized by two different methods: incipient impregnation with aqueous solution of the acid and mechanochemical synthesis. The samples were tested in the reaction of the thiophene hydrodesulfurization after activation with mixture H₂ + H₂S. The effect of the preparation method of the catalysts on their physicochemical and catalytic properties has been studied. A partial destruction of the loaded compound is observed in mechanochemically treated sample whereas the aggregates are formed from the particles of different size in the impregnated sample. The specific surface area of the sample prepared by mechanical–chemical treatment decreases 2–3 times, while the total pore volume is about four times lower. The HDS activity is higher on the impregnated sample than on the mechanochemically treated one.     

Electrical characterization of carbon nanotube Y-junctions: a foundation for new nanoelectronics

A review on the syntheses and electrical characterization of Y-shaped multi-walled carbon nanotube morphologies is presented. Modified thermal CVD processes, using Ti precursors, are used to grow Y-junctions of different geometries and distribution of catalyst particles. It has been established that novel electrical switching behavior is feasible, where any one of the three branches of the Y-junction can be used for modulating the electrical current flow through the other two branches. Current blocking behavior, leading to perfect rectification, is seen which could be related to the interplay of the carrier lifetime and the transit time. The overall goal is to investigate the possibility of obtaining novel functionality at the nanoscale, which can lead to new device paradigms.     

Critical slowing down in lead magnesium niobate–zirconate ceramic

Dielectric relaxation behaviour of (1 − x)PMN − xPZ, for x = 0.10, 0.30 and 0.40 have been studied. The nature of relaxational behaviour was found to change with PZ concentration. A crossover from a static freezing to critical slowing down like behaviour is observed with increase in Zr⁴⁺ concentration. We have used Glazounov and Tangastev criterion to distinguish freezing and critical slowing down like behaviour.     

Probing the thermal decomposition process of layered double hydroxides through in situ <Superscript>57</Superscript>Fe Mössbauer and in situ X-ray diffraction experiments

The thermal decomposition properties of Mg–Fe hydrotalcites were studied through in situ ⁵⁷Fe Mössbauer spectroscopy and in situ X-ray diffraction. Abrupt changes in the quadrupolar splitting measured in the Mössbauer spectra revealed a phase transition from the starting lamellar structure to a new crystalline arrangement. By analyzing the Mössbauer parameters we show that the material is highly disordered in the 300–400 °C temperature range. This hypothesis is confirmed by the X-ray results whose diffractograms indicated the collapse of the lamellar structure and the formation of a solid solution.     

Modelling of effects of ultrastructural morphology on the hygroelastic properties of wood fibres

Wood fibres constitute the structural framework of e.g. wood, paper, board and composites, where stiffness and dimensional stability are of importance. An analytical modelling approach has been used for prediction of hygroelastic response, and assessment of the stresses in thick-walled cylinder models of wood fibres. A wood fibre was idealised as a multilayered hollow cylinder made of orthotropic material with helical orientation. The hygroelastic response of the layered assembly due to axisymmetric loading and moisture content changes was obtained by solving the corresponding boundary value problem of elasticity. A simple solution scheme based on the state space approach and the transfer matrix method was employed. This was combined with an analytical ultrastructural homogenisation method, used to link hygroelastic properties of constituent wood polymers to properties of each layer. Predicted hygroelastic response captured experimentally measured behaviour. Fibres that were constrained not to twist showed a stiffer response than fibres allowed twisting under uniaxial loading. It was also shown that the ultrastructure, i.e. the microfibril angle, will control the hygroexpansion in the same way as it controls the compliance of the cell wall. Qualitative failure trends comparable with experimental observations could be established with stress analysis and a simple plane-stress failure criterion.     

Effect of gamma irradiation on the optical properties of CR-39 polymer

The UV-Visible absorption spectra of virgin and gamma irradiated (20–800 kGy) CR-39 polymer have been deduced by using Shimadzu Double beam Double Monochromator UV-Visible Spectrophotometer (UV-2550). The existence of the peaks, their shifting and broadening as a result of gamma irradiation has been discussed. Finally the indirect and direct band gap in virgin and gamma irradiated CR-39 has been determined. The values of indirect band gap have been found to be lower than the corresponding values of direct band gap.     

Dielectric and thermal characteristics of gel grown single crystals of ytterbium tartrate trihydrate

Dielectric and thermal characteristics of gel grown single crystals of ytterbium tartrate trihydrate have been carried out. The dielectric constant has been measured as a function of frequency in the range 2 kHz–1 MHz and temperature range 30–300 °C. The dielectric constant increases with temperature, attains a peak near 215 °C, and then decreases as the temperature exceeds 215 °C. The dielectric anomaly at 215 °C is suggested to be due to phase transition brought about in the material. The dielectric behaviour of the material is correlated with the results on thermal analysis. Thermogravimetric and differential thermal analysis have been used to study the thermal characteristics of the material. The experimental results show that the material is thermally stable up to 200 °C. The decomposition process occurs in two stages until ytterbium oxide is formed at 700 °C. The non-isothermal kinetic parameters e.g., activation energy and the frequency factor have been evaluated for each stage of thermal decomposition by using the integral method, applying the Coats–Redfern approximation.     

Hydrogen adsorption studies in micro-size cobalt dots

Hydrogen desorption curves were obtained from a sample composed of a square arrangement of Co dots with average diameter of 4.4 μm, separated by a distance of 11.6 μm. A macroscopic sample of Co dots grown on a 2.5 × 2.5 cm Si substrate was made by standard lithographic techniques and used in these experiments. Thermal programmed desorption (TPD) was performed under ultra-high vacuum conditions. Hydrogen TPD curves were obtained from a 1 × 1 cm Co dots samples displaying a maximum of intensity at 425 K. Hydrogen TPD curve was also obtained from 1 cm× 1 cm samples of Co films and Co foils for comparison. The hydrogen TPD curves have decreasing intensity from the Co foils to the Co dots and finally to the Co films. This indicates that there are more sites for hydrogen adsorption on the Co dots than in the Co films. This is a surprising result because there is approximately 8.7 times less Co atoms exposed in the Co dots that in the Co film sample. A desorption energy of 27 kcal/mol was obtained for the Co dots suggesting that hydrogen is adsorbed on an hcp hollow site of the Co dot crystalline structure.     

A review on the synthesis of in situ aluminum based composites by thermal,mechanical and mechanical–thermal activation of chemical reactions

The aim of the present paper is to review the recent progress in the synthesis of in situ particle reinforced aluminum composites using thermal, mechanical and combined mechanical-thermal activation of aluminothermic reduction reactions. The combination of combustion synthesis (CS) and mechanosynthesis (MS) is the most recent development in the processing of advanced materials like micro and nano aluminum based composites. The combined mechanical thermal synthesis (MTS) has widened the possibilities for both CS and MS. MTS holds great potential for commercial viability and offers exciting processing route for the synthesis of advanced materials. Enhanced reaction kinetics and extended concentration limits in MTS are demonstrated by illustrating the synthesis of aluminum based nanocomposite involving Al–CeO₂.