Molecular dynamics study of nano mass transfer in a vibrating cantilevered carbon-nanotube

We investigate the nano mass transfer in an ultrahigh frequency carbon-nanotube-resonator encapsulating a nanocluster via classical molecular dynamics simulations. When the carbon-nanotube-resonator vibrated, the encapsulated copper nanocluster more rapidly approached the end of the cantilevered carbon-nanotube-resonator. Such phenomena were due to the migration of the encapsulated copper nanocluster due to the centrifugal force induced by the vibrating nanotube resonator. So the resonance frequency change could be time-dependently found. For the movable copper nanocluster in carbon nanotube resonator, the vibrational spectra when the copper nanocluster inside the carbon nanotube resonator rapidly settled at the capped edge were different from those obtained when the copper nanocluster continuously oscillated inside the carbon nanotube resonator. Such results showed that the frequency of the carbon-nanotube-resonator encapsulating the movable copper nanocluster could be adjusted by controlling the mean position of the oscillating copper nanocluster. The movable nanocluster inside a carbon-nanotube can be applied to a nanotube-based data storage media by sensing the position of the nanocluster.     

Reduce cell to cell charge interference by virtual ground inclusion in 3-dimensional vertical gate NAND flash memory

In this work, we propose a structural modification to the 3-dimensional vertical gate NAND flash memory that will reduce the charge interference caused by stored charge on the opposite facing cell. In the barrier oxide structure (BOS), an oxide layer was inserted into the center of the body to physically block the conduction electrons moving to and from the channel regions influenced by the charge stored on either of the Oxide-Nitride-Oxide (ONO) trap layers. In the virtual ground structure (VGS), a highly p-type doped poly silicon layer was inserted to act as a virtual ground to reduce the electric-field changes caused by the stored change on the ONO trap layers. We investigated the I-V characteristics of the different structures using 3-D TCAD simulation tool, depending on the body type (crystalline or poly silicon) at double programming and single programming. We confirmed that the charge interference problem was reduced significantly by the BOS and VGS modifications in the crystalline silicon and high quality poly silicon body structures.     

Advanced lithography simulation for various 3-dimensional nano/microstructuring fabrications in positive- and negative-tone photoresists

Photoresist lithography has been applied to the fabrication of micro/nano devices, such as microfluidic structures, quantum dots, and photonic devices, in MEMS (micro-electro mechanical systems) and NEMS (nano-electro-mechanical systems). In particular, nano devices can be expected to present different physical phenomena due to their three-dimensional (3D) structure. The flexible 3D micro/nano fabrication technique and its process simulation have become among the major topics needed to understand nano-mechanical phenomena. For this purpose, the moving-mask technology and the lithography processes for the positive- and negative-tone photoresists were modeled. The validity of the simulation of the proposed 3D nano/microstructuring was successfully confirmed by comparing the experiment results and the simulated results. Hence, the developed model and the simulation can present and optimize photoresist characteristics and lithography process conditions due to the various 3D nano/microstructures. They could be help in the understanding of nanomaterial and mechanical phenomena.     

Transparent conductive film fabrication using intercalating silver nanoparticles within carbon nanotube layers

Carbon nanotubes have received attention as alternative materials to indium tin oxide for application in transparent conductive films. Their electrical conductivity, however, still has to be improved. In this study, a layer-by-layer self-assembly process was demonstrated using nano-silver-coated carbon nanotubes, which help improve electrical conductivity. The method was based on the pi-pi interaction between the side walls of the carbon nanotubes and nano-silver clusters that were functionalized with benzyl mercaptan. The self-assembled nano-silver cluster monolayer on the surface of the nanotubes can reduce the interfacial contact resistance, thereby leading to high conductivity at a high transparency. The compound was characterized via scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Raman spectroscopy, and the four-point probe method.     

Analysis of the inorganic component of autogenous tooth bone graft material

This study was performed to identify the calcium phosphate minerals, chemical element and Ca/P ratio and to examine the surface structure of autogenous tooth bone grafting material (AutoBT) which recently developed and applied clinically as a bone graft materials. The analytical results showed that AutoBT is composed of low-crystalline hydroxyapatite (HA) and possibly other calcium phosphate minerals, which is similar to the minerals of human bone tissues. And the dental crown portion was composed of high-crystalline calcium phosphate minerals (mainly HA) with higher Ca/P ratio while the root portion was mainly composed of low-crystalline calcium phosphates with relatively low Ca/P ratio.     

Development of a robotic system for the bed-ridden

The ability to live without the help of a caretaker enhances the quality of life of those who are bed-ridden or confined to a wheel-chair. A lot of systems have been proposed to support the daily life of bed-ridden. A smart home, especially a bed-type robot system, can help the movement and action of patients.This paper discusses the development of an intelligent bed robot system (IBRS), which can help the elderly and the disabled have independent life in bed. The IBRS is a special bed equipped with two robot arms and an array of pressure sensors attached to the mattress. The pressure distribution on the mattress is used to estimate the pose of the patient, and an appropriate assistance is provided by the robot arms. The proposed system has been tested experimentally for its effectiveness while maximizing the therapeutic outcome.     

Evaluation of electromagnetic loads on various design options of the ITER diagnostic upper port plug during plasma disruptions

Electromagnetic (EM) loads due to eddy current and halo current during plasma disruptions are evaluated for the ITER diagnostic upper port plug. To reduce strong EM loads acting on the port plug fixed to the vacuum vessel like a cantilever beam, three design options have been considered: removal of the diagnostic first wall, slitting of the diagnostic shield module and recess of the port plug. The main focus of the present study is to examine the efficacy of these options in terms of EM loads on the upper port plug. It is found that making slits is more effective than removing the first wall. It is also shown that the upper port plug needs to be recessed to reduce the EM load induced by halo current.     

Too much of a good thing: Curvilinear relationships between personality traits and job performance.

The relationships between personality traits and performance are often assumed to be linear. This assumption has been challenged conceptually and empirically, but results to date have been inconclusive. In the current study, we took a theory-driven approach in systematically addressing this issue. Results based on two different samples generally supported our expectations of the curvilinear relationships between personality traits, including Conscientiousness and Emotional Stability, and job performance dimensions, including task performance, organizational citizenship behavior, and counterproductive work behaviors. We also hypothesized and found that job complexity moderated the curvilinear personality–performance relationships such that the inflection points after which the relationships disappear were lower for low-complexity jobs than they were for high-complexity jobs. This finding suggests that high levels of the two personality traits examined are more beneficial for performance in high- than low-complexity jobs. We conclude by discussing the implications of these findings for the use of personality in personnel selection. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Combination treatment of alkaline electrolyzed water and citric acid with mild heat to ensure microbial safety, shelf-life and sensory quality of shredded carrots

The objective of this study was to determine the synergistic effect of alkaline electrolyzed water and citric acid with mild heat against background and pathogenic microorganisms on carrots. Shredded carrots were inoculated with approximately 6-7 log CFU/g of Escherichia coli O157:H7 (932, and 933) and Listeria monocytogenes (ATCC 19116, and 19111) and then dip treated with alkaline electrolyzed water (AlEW), acidic electrolyzed water (AcEW), 100 ppm sodium hypochlorite (NaOCl), deionized water (DaIW), or 1% citric acid (CA) alone or with combinations of AlEW and 1% CA (AlEW + CA). The populations of spoilage bacteria on the carrots were investigated after various exposure times (1, 3, and 5 min) and treatment at different dipping temperatures (1, 20, 40, and 50 °C) and then optimal condition (3 min at 50 °C) was applied against foodborne pathogens on the carrots. When compared to the untreated control, treatment AcEW most effectively reduced the numbers of total bacteria, yeast and fungi, followed by AlEW and 100 ppm NaOCl. Exposure to all treatments for 3 min significantly reduced the numbers of total bacteria, yeast and fungi on the carrots. As the dipping temperature increased from 1 °C to 50 °C, the reductions of total bacteria, yeast and fungi increased significantly from 0.22 to 2.67 log CFU/g during the wash treatment (p ≤ 0.05). The combined 1% citric acid and AlEW treatment at 50 °C showed a reduction of the total bacterial count and the yeast and fungi of around 3.7 log CFU/g, as well as effective reduction of L. monocytogenes (3.97 log CFU/g), and E. Coli O157:H7 (4 log CFU/g). Combinations of alkaline electrolyzed water and citric acid better maintained the sensory and microbial quality of the fresh-cut carrots and enhanced the overall shelf-life of the produce.     

Functionality and physico-chemical characteristics of bovine and caprine mozzarella cheeses during refrigerated storage

Low moisture part-skim Mozzarella cheeses (MC) were manufactured using fresh bovine and caprine milk to study melting, physico-chemical, textural, and microstructural properties of the cheeses during 8 wk of refrigerated storage. Structural changes in cheese matrix were evaluated by scanning electron microscopy and by proteolytic patterns using nitrogen solubility, SDS-PAGE, and Gel-pro analyzer. Meltability of ripened cow and goat MC were not different when fat content of both milks were standardized, whereas bovine MC formed a significantly larger amount of free oil throughout the experiment. The results of the proteolytic patterns, texture attribute (cohesiveness), and microstructure revealed that bovine MC had a greater structural degradation of cheese matrix than caprine MC during the storage. Elevated protein degradation in bovine MC led to more intense brown color formation than the goat counterpart when the cheeses were baked. The melting characteristics showed high positive correlation (r = 0.51 to 0.80) with proteolysis, whereas it was negatively correlated with textural characteristics. Among textural attributes, cohesiveness was highly inversely correlated with melting characteristics (r = -0.69 to -0.88). High negative correlations were also observed between proteolytic parameters and textural attributes (r = -0.48 to -0.81).