Unsteady behavior of leading-edge vortex and diffuser stall in a centrifugal compressor with vaned diffuser

The characteristics of a rotating stall of an impeller and diffuser and the evolution of a vortex generated at the diffuser leading-edge (i.e., the leading-edge vortex (LEV)) in a centrifugal compressor were investigated by experiments and numerical analysis. The results of the experiments revealed that both the impeller and diffuser rotating stalls occurred at 55 and 25 Hz during off-design flow operation. For both, stall cells existed only on the shroud side of the flow passages, which is very close to the source location of the LEV. According to the CFD results, the LEV is made up of multiple vortices. The LEV is a combination of a separated vortex near the leading- edge and a longitudinal vortex generated by the extended tip-leakage flow from the impeller. Therefore, the LEV is generated by the accumulation of vorticity caused by the velocity gradient of the impeller discharge flow. In partial-flow operation, the spanwise extent and the position of the LEV origin are temporarily transmuted. The LEV develops with a drop in the velocity in the diffuser passage and forms a significant blockage within the diffuser passage. Therefore, the LEV may be regarded as being one of the causes of a diffuser stall in a centrifugal compressor.     

Acceleration of the redox kinetics of VO2+/VO2 + and V3+/V2+ couples on carbon paper

The redox kinetics of VO²⁺/VO₂ ⁺ and V³⁺/V²⁺ couples on a carbon paper (CP, HCP030 N, Shanghai Hesen, Ltd., China) electrode were investigated in terms of their standard rate constant (k ₀) and reaction mechanism. The values determined for k ₀ for VO²⁺ ?? VO₂ ⁺ and V³⁺ ?? V²⁺ using the CP electrode are 1.0 × 10^?3 and 1.1 × 10^?3 cm s^?1, respectively. The value of k ₀ increases by one or two order(s) of magnitude compared with values obtained using electrodes composed of pyrolytic graphite and glassy carbon. The acceleration of the redox kinetics of vanadium ions is a result of the large surface area of the CP electrode. An inner-sphere mechanism for the reaction on the surface of the electrode is proposed. The kinetic features of vanadium redox reactions on the CP electrode reveal that CP is suitable for use as the electrodes in vanadium redox-flow batteries.     

Developmental ability of cloned embryos from neural stem cells

The success rate is generally higher when cloning mice from embryonic stem (ES) cell nuclei than from somatic cell nuclei, suggesting that the embryonic nature or the undifferentiated state of the donor cell increases cloning efficiency. We assessed the developmental ability of cloned embryos derived from cultured neural stem cell (NSC) nuclei and compared the success rate with that of embryos cloned from other donor cells such as differentiated NSCs, cumulus cells, Sertoli cells and ES cells in the mouse. The transfer of two-cell cloned embryos derived from cultured NSC nuclei into surrogate mothers produced five live cloned mice. However, the success rate (0.5%) was higher in embryos cloned from cultured NSC nuclei than from differentiated NSCs (0%), but lower than that obtained by cloning mice from other cell nuclei (2.2-3.5%). Although the in vitro developmental potential to the two-cell stage of the cloned embryos derived from NSC nuclei (73%) was similar to that of the cloned embryos derived from other somatic cell nuclei (e.g., 85% in Sertoli cells and 75% in cumulus cells), the developmental rate to the morula-blastocyst stage was only 7%. This rate is remarkably lower than that produced from other somatic cells (e.g., 50% in Sertoli cells and 54% in cumulus cells). These results indicate that the undifferentiated state of neural cells does not enhance the cloning efficiency in mice and that the arrest point for in vitro development of cloned embryos depends on the donor cell type.     

Effect of annealing conditions on the uniformity of undoped Semi-Insulating InP

Recently, it was found that undoped semi-insulating InP can be obtained by highpressure annealing of high purity materials. The reproducibility and the uniformity was, however, not satisfactory. In the present work, we found that not only Fe concentrations but also Cr and Ni concentrations in annealed wafers were slightly increased during annealing. Since it seems that the origin of the contamination was due to the vapor source of red phosphorus, conductive InP with a trace amount of Fe was annealed under low phosphorus vapor pressure in order to reduce the contamination. By preventing the contamination of Cr and Ni, preparation of semi-insulating InP became highly reproducible. The minimum Fe concentration for realizing semi-insulating InP was found to be 1 x 10¹⁵cm⁻³. It was also found that the better resistivity uniformity can be obtained at higher annealing temperatures.     

Quantitative analysis for reaction between epoxidized natural rubber and poly (L‐lactide) through 1H‐NMR spectroscopy

Reaction between epoxidized natural rubber and poly(L ‐lactide) (PLLA) was investigated quantitatively in terms of conversion of the epoxidized natural rubber. The epoxidized natural rubber was prepared by epoxidation of high ammonia natural rubber (HA‐NR) or deproteinized natural rubber (DPNR) with peracetic acid followed by depolymerization with ammonium persulfate. The resulting liquid HA‐NR having epoxy group (LENR) or liquid DPNR having epoxy group (LEDPNR) were subjected to heating at 473 K for 20 min, after blending with PLLA. The products were characterized through morphology observation, DSC measurement, and ¹H‐NMR spectroscopy. The conversions of the rubbers were estimated from intensity ratio of signals in ¹H‐NMR spectrum for the products after removing unreacted rubber with toluene. Difference in the estimated conversion between the LENR/PLLA and LEDPNR/PLLA blends was interpreted in relation to proteins present in the rubber. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Microstructure of a Molybdenum Nitride Layer Formed by Nitriding Molybdenum Metal

For pure molybdenum nitrided at 1373 K in NH₃ gas, microstructural observations of a molybdenum nitride layer were conducted through a transmission electron microscope. The molybdenum nitride layer consisted of two molybdenum nitrides: an outer one of γ-Mo₂N and an inner one of β-Mo₂N. A great number of (011)[0     1] type twins were observed in the β-Mo₂N phase, whereas the microstructure of the γ-Mo₂N phase was almost free from lattice defects except for slightly observed {111}〈112〉 type twin.     

Preliminary spectrum shifter design for intermediate energy nuclear data benchmark experiments with DT neutrons

Integral benchmark experiments with DT neutrons are not always sufficient for nuclear data benchmarking in the MeV region, below 10 MeV. A neutron spectrum shifter, which will be placed between a sample and a DT neutron source, is effective to moderate DT neutrons incident to the sample. In order to estimate effects of the spectrum shifter, the ratio of the contribution of 14 MeV neutrons in the leakage neutron and gamma-ray spectra was calculated with MCNP-4C for an experimental configuration at FNS of JAEA, Japan. The calculations were carried out for a Li₂TiO₃ sample with a Be, D₂O, or ⁷LiD spectrum shifter. It was found out that the Be shifter was superior to others and the Be shifter was effective to decrease the contribution of 14 MeV neutrons especially for secondary gamma-ray spectrum measurements.     

Biodesulfurization of dibenzothiophene with Rhodococcus erythropolis ATCC 53968 and its mutant in an interface bioreactor

An interface bioreactor was used in the biodesulfurization (BDS) of dibenzothiophene (DBT) with Rhodococcus erythropolis ATCC 53968. Although this strain could efficiently degrade DBT to 2-hydroxybiphenyl (2-HBP), the microbial film peeled off from the surface of the carrier (agar plate) to an organic phase (dodecane or tetradecane). To overcome this problem, a UV mutant, which strongly adhered to the carrier surface, was obtained by a new screening method. The best UV mutant (UM-021) could efficiently catalyze the BDS and the microbial film did not peel off from the surface of the carrier to tetradecane layer.     

Water vapor adsorption properties of amorphous cefditoren pivoxil evaluated by adsorption isotherms and microcalorimetry

Water vapor adsorption of ground cefditoren pivoxil was studied. The amount of water adsorbed increased with a decrease in the crystallinity of cefditoren pivoxil. It was found from the microcalorimetric measurements that the differential heat of water vapor adsorption at 1.5% adsorbed water increased with decreasing crystallinity of cefditoren pivoxil, suggesting that hygroscopicity of cefditoren pivoxil was enhanced by grinding. These results indicated that hydrophilic adsorption sites in cefditoren pivoxil increased through the grinding process. The results of infrared (IR) spectra examination suggested that the increment of hydrophilic adsorption sites through the grinding process resulted from the change of the environment of the carbonyl groups in two esters and amide.