原油常减压装置节能技术

由于常减压装置消耗能量约占炼油厂总用能的25％～30％，已成为炼油厂中消耗量最大的装置，因此，我国各炼油厂对常减压装置进行以降低能耗为中心的技术改造就显得十分必要。详细介绍了适用于常减压装置节能的新工艺、新设备以及优化操作。工艺方面主要有采用过滤脱盐新技术对原油进行深度脱盐、采用强化蒸馏新工艺提高原油蒸馏拔出率、优化产出、增产柴油；设备方面主要使用规整填料和新型塔板改善分馏塔分馏效率、使用新型燃烧器提高加热炉效率、使用新型换热器提高热回收率、采用变频技术降低装置电耗；优化操作方面主要有利用计算机进行监控与管理和改善操作条件。最后对国内原油常减压装置节能改造提出了一些建议，以供炼油企业在进行原油常减压装置改造时参考。     

井下乳化/水热催化裂解复合降黏开采稠油技术研究

实验考察了胜利孤东稠油井下催化水热裂解和乳化/催化水热裂解降黏效果。所用催化剂为水溶性铁镍钒体系,Fe3+∶Ni2+∶VO4+=5∶1∶1,100 g稠油与30 g 0.5%催化剂水溶液在240℃反应24小时。原始黏度(50℃)11.0和8.36 Pa.s的两种稠油裂解并静置除水后,黏度降低76.2%和75.6%,室温放置60天后降黏率下降小于3个百分点,气相色谱显示裂解后轻组分明显增加,红外光谱显示稠油组分发生脱羧反应且芳环数减少。讨论了稠油催化水热裂解反应机理。所用化学助剂JN-A在油水中均可溶,耐温达250℃,耐矿化度达50 g/L,其水溶液以30∶100的质量比与稠油混合时形成低黏度的O/W乳状液。当水相含1.0%JN-A和0.5%催化剂时,两种稠油水热裂解后的反应混合物为O/W乳状液,黏度仅为319和309 mPa.s,静置除水后的稠油降黏率增加到86.5%和87.3%,其中的轻组分含量进一步增加。该井下乳化/催化水热裂解复合降黏法成功地用于孤东两口蒸汽吞吐井,稠油井作业后初期采出的原油黏度由~9 Pa.s降低到1 Pa.s左右,随采油时间延长而逐渐升高,约50天后超过4Pa.s。图2表6参5。     

溶胶--凝胶镀膜技术综述(连载5)

第三节　常见氧化物膜目前研究最多的氧化物膜可谓二氧化硅和二氧化钛膜 ,这两种薄膜也是接受呈色离子、制备彩色镀膜常用的基体膜 ,所以 ,有必要将它们单独列出 ,加以讨论。1　二氧化钛膜在所有高折射率材料中 ,由钛的化合物制备的氧化物膜具有特殊的实际意义。因此 ,对二氧化     

三网互联的几个关键技术

对三网互联的几个关键技术进行分析与研究，介绍利用IP技术解决有线电视网地址选择问题，探讨怎样将ATM技术与IP技术相互融合，使真正的信息高速公路成为现实，阐述利用H．323标准全面解决视频网络方案。     

Throughput analysis for multicast switches with multiple input queues

This letter analyzes the saturated throughput for multicast switches with multiple input queues per input port. Under the assumptions of a Poisson uniform traffic model and random packet scheduling policy, we derive the multicast switch saturated throughput under different fanouts. To verify the analysis, extensive simulations are conducted with different switch sizes and fanouts. It is shown that the theoretical analysis and the simulation results have a discrepancy less than 1.9%. Results from this letter can be used as a guidance to design the optimal queuing for multicast switches.     

Dispersion-relation-preserving FDTD algorithms for large-scale three-dimensional problems

We introduce dispersion-relation-preserving (DRP) algorithms to minimize the numerical dispersion error in large-scale three-dimensional (3D) finite-difference time-domain (FDTD) simulations. The dispersion error is first expanded in spherical harmonics in terms of the propagation angle and the leading order terms of the series are made equal to zero. Frequency-dependent FDTD coefficients are then obtained and subsequently expanded in a polynomial (Taylor) series in the frequency variable. An inverse Fourier transformation is used to allow for the incorporation of the new coefficients into the FDTD updates. Butterworth or Chebyshev filters are subsequently employed to fine-tune the FDTD coefficients for a given narrowband or broadband range of frequencies of interest. Numerical results are used to compare the proposed 3D DRP-FDTD schemes against traditional high-order FDTD schemes.     

不同注F剂量与CMOS运放电路辐照损伤的相关性

在不同注F剂量条件下,对P沟和N沟两种不同差分对输入CMOS运放电路的电离辐照响应进行了研究.分析比较了注F和未注F运放电路电离辐照响应之间的差异.结果表明,在栅场介质注入适量的F,可有效抑制辐照感生的氧化物电荷尤其是界面态的增长,从而提高CMOS运放电路的抗辐照特性.     

Gamma-irradiation-induced Ag/SiO2 composite films and their optical absorption properties

Small Ag particles or clusters dispersed mesoporous SiO₂ composite films were prepared by a new method: First the matrix SiO₂ films were prepared by sol-gel process combined with the dip-coating technique, then they were soaked in AgNO₃ solutions followed by irradiation of γ-ray at room temperature and in ambient pressure. The structures of these films were examined by X-ray diffraction (XRD), high-resolution transmission electron microscope (HRTEM), and optical absorption spectroscopy. It has been shown that the Ag particles grown within the porous SiO₂ films are very small, and they are isolated and dispersed from each other with very narrow size distributions. With increasing the soaking concentration and an additional annealing, an opposite peakshift effect of the surface plasmon resonance (SPR) was observed in the optical absorption measurements.     

数值试井在白6-2井测试资料分析评价中的应用

数值试井是在近来发展的一项新的试井解释技术，具有处理非均质，复杂边界油气藏问题的优点，弥补了常规解析试井技术的不足。运用数值试井解释技术，结合动、静态资料，通过对白6-1断块白6-2井测试资料的综合分析评价，确定了储层渗流参数，落实了该气藏的边界情况，为该断块下一步开发提供可靠依据。     

工业管道测厚的几点问题探讨

超声波测厚在腐蚀监测上应用越来越广泛,为让这项检测技术更准确、更可靠,充分发挥功效,文章就工业管道测厚中测厚数据处理、测厚点选择、高温问题以及其它影响因素等几个方面进行了探讨。