Grain-growth-inhibiting effects of primary inclusion particles of ZrO2 and MgO in Fe-10 mass pct Ni alloy

Grain-growth inhibition in an Fe-10 mass pct Ni alloy, which was continuously cooled from a melt, was studied at 1673 K in the presence of primary deoxidation products of ZrO₂ or MgO particles. The mean grain size and grain-size distribution in a cross section were measured as a function of holding time for up to 240 minutes. The grain growth was strongly inhibited by the inclusion particles and was influenced by the dissolved Zr. In the Zr deoxidation, the number of particles per unit area (N _A) ranged from 80 to 650 mm⁻², the ZrO₂ particle size ( ) varied from 1.1 to 1.6 μm, and the dissolved Zr level was below 1800 mass ppm. In the Mg deoxidation, the particle-number density was 90 to 270 mm⁻², the MgO particle size was 1.1 to 1.7 μm, and the dissolved Mg level was below 20 mass ppm. In a logarithmic plot of the ratio of limiting mean grain diameter ( ) to the mean particle diameter ( ) against the volume fraction of particles (f _V), both the value for a given f _V value, which ranged from 0.014 to 0.074 pct, and the slope were significantly lower than that predicted from the two-dimensional relation =(4/π) · f _V ^/−1 , i.e., Zener’s limit. This discrepancy is discussed in light of the fraction of particles at the grain boundaries measured experimentally. Normal grain growth was confirmed from the grain-size distribution observed as a function of holding time, which was best described by the log-normal distribution.     

Histamine modulates high-voltage-activated calcium channels in neurons dissociated from the rat tuberomammillary nucleus

Insects are known to be useful in estimating the postmortem interval (PMI). Here several cases are reported which show that a wide range of applications in medicolegal questions and hygiene together or apart from estimating the PMI can be answered by use of forensic entomology techniques, including close observation of larval development. Case 1 describes how blowfly larvae fell from a putrefied corpse, hid, and finally emerged from pupae three months after disinfection and renovation. In case 2, the entomological state of the decomposed corpse of a heroin user is described. Case 3 deals with a single adult Protophormia terranovae found in the skull of a partially mummified woman. Case 4 reports the finding of Serratia marcescens bacteria in red Muscina stabulans pupae which were found on a 5-day-old corpse. In case 5, blowfly eggs on the corpse of another heroin user are interpreted as an indication of the decedent being laid outside at night after his death in a flat. Case 6 deals with the finding of Parasarcophaga argyrostoma, which in Cologne might be an indicator species which tells if a corpse was lying outside at least for some time.     

Dynamic analysis of cracked linear viscoelastic solids by finite element method using singular element

The finite element method for the dynamic problem of cracked linear viscoelastic solids is developed using the singular element where the displacement function is taken from the analytical solution near the crack-tip. The time variation of the dynamic stress intensity factors is determined for a center crack and an oblique crack in standard linear viscoelastic rectangular plates subjected to dynamic loading.

---

Résumé La méthode par éléments finis permettant d'aborder le problème dynamique des solides linéaires viscoélastiques fissurés est développée en recourant à un élément singulier pour lequel la fonction de déplacement est prise dans une solution analytique au voisinage del'extrémité de la fissure. La variation dans le temps des facteurs d'intensité de contrainte dynamique est déterminée pour une fissure centrale et pour une fissure oblique dans des plaques rectangulaires standard en matériau linéaire viscoélastique soumises à une sollicitation dynamique.

     

Defect levels in chromium-doped silicon

The transient capacitance technique has been used to study the chromium-related levels in the silicon band gap. Chromium was diffused at temperature of 1100 and 1150°C for 0.5 and 3 hr. Five different levels at E_c?0.11 eV, E_c?0.21 eV, E_c?0.28 eV, E_c?0.36 eV and E_c?0.45 eV were obtained from the Arrheniu plots of the electron thermal-emission rates. The number of levels in the upper half of the band gap decreased from five to two with an increase of Cr-diffusion period. Two levels were located at E_c?0.20 eV (donor) and E_c?0.43 eV (acceptor). A donor level was also observed at E_v + 0.25 eV. The donor level was not affected by the diffusion condition. The majority carrier capture cross sections of the three dominant levels have been measured by the transient capacitance technique modified by the pulse transformer. The values were σ_n = 4.1 × 10^?15 cm² for the upper donor at E_c?0.20 eV, σ_n = 2.0 × 10^?16 cm² for the acceptor at E_c ?0.43 eV and σ_p = 9.1 × 10^?18 cm² for the lower donor at E_v + 0.25 eV, and were independent of temperature. The three dominant levels are due to distinct chromium centers.     

Changes in photovoltaic and dark electrical properties of hydrogenated amorphous silicon diodes induced by forward bias carrier injection

The photovoltaic and dark electrical properties of hydrogenated amorphous silicon diodes were changed by forward bias carrier injection for several hours. These changes were similar to photoinduced (PI) changes previously reported, and this result supports previous explanations for PI changes. The differences between these two types of change are also discussed.     

Ns-kriging based microstructural optimization applied to minimizing stochastic variation of homogenized elasticity of fiber reinforced composites

This paper describes an approximate microstructural optimization using the ns-kriging (noise-resistant smoothed kriging) method for minimizing the maximum stochastic variation of homogenized elastic properties of a composite material caused by microscopic uncertainties of component materials. Since evaluation of a stochastic characteristic of a homogenized material property such as expectation or variance will involve a high computational cost and its results include inaccuracy in using the Monte Carlo simulation, an approximation-based optimization technique is useful for solving the optimization problem considering the multiscale stochastic problem. Especially, the ns-kriging will work well in case of using inaccurate data for an unknown objective function. In order to investigate applicability and effectiveness of the proposed ns-kriging based approach to the optimization problem, it is applied to the cross-sectional shape optimization of fiber in a unidirectional FRP. From the numerical results, validity and effectiveness of the proposed approach are confirmed.     

Friction and frictional tracks on thick silica films prepared by vacuum deposition

Friction and frictional tracks on 2 µm thick SiO₂ films evaporated on polymethylmethacrylate (PMMA) substrate were investigated. Diamond spherical sliders of radius 30 and 100 µm, respectively, were slid on these coatings under a load of 50 to 200g at a sliding speed of 15 cm min^–1. The static and dynamic friction coefficients for SiO₂ films were found to be 0.1 and 0.06, respectively, depending on the load and radius of the slider. For lower load and small slider radius the tracks on SiO₂ film were groove-like, and whisker-like cracks regularly grew from the edges of the tracks. For higher loads and larger slider radius, semicircular cracks in the film were regularly found behind the slider, but in thicker film (6 µm thick), circular cracks occurred. The origin of these cracks is discussed in terms of a tension zone produced around the contact area between the slider and the substrate under frictional force.     

Mixed powder coating film using thermoplastic polyester and its alkaline resistance

To improve alkaline resistance, a newly mixed powder coating film using thermoplastic polyethylene terephthalate (PET) was investigated. Two kinds of polyvinyl butyral (PVB) and two kinds of polyamide (PA) were chosen as the secondary polymer. The melting temperatures (T _ms) of these materials were lower than that of primary PET polymer so the mixed powder coating was able to form a dual phase film through a fluidized bed coating process. Microscope and Fourier transform infrared spectroscopy (FTIR) observations revealed that the dual phase structure was indeed successfully formed and there was a secondary layer over the entire surface area of the film. This mixed powder coating film significantly enhanced the alkaline resistance to an environment filled with NaOH solution at 40°C in which a secondary material would be effective in protecting the film. With regard to both alkaline resistance and film formability, PET/PVB was superior to the PET/PA mixture.     

A bag carrier for continuous intravenous hyperalimentation

We designed a new bag-carrier device system for continuous intravenous hyperalimentation. The patient carries it on his shoulder and can both walk up and down stairs and go out. The use of this device is simple and easy, and was found to increase the patient's opportunity to engage in physical activity.