应用ITO膜作电荷收集极的位置灵敏探测器

首次尝试将ITO（Indium Tin Oxide）膜与微通道板（Microchannel Plate）结合用作位置灵敏探测器，并对该探测器的线性、位置分辨及探测效率作了测试，得到了令人满意的结果。     

低压宽温高频铝电解电容器工作电解液

在传统的己二酸铵/乙二醇加水体系中,通过增加水的含量实现高电导率,同时在电解液中添加多种有机高分子物质形成复合添加剂,改善工作电解液的高温稳定性,使电容器上限工作温度扩展到105℃,形成高频宽温低阻抗工作电解液。     

倾斜水塔的爆破拆除

针对某部倾斜水塔的定向爆破拆除,从防止水塔倾倒偏移和筒体触地冲击地面对周围环境造成影响等不利情况,确定爆破方案和采取相应的防护措施.     

大型钢制焊接双层低温储罐设计建造

介绍了大型钢制焊接双层低温储罐的结构形式、选材、建造、检验及保冷要求 ,结合所设计的低温液氨储罐 ,对设计建造这类储罐必须考虑的一些问题作了分析     

Effect of bulk flow pulsations on film cooling with compound angle holes

Experiments are conducted to investigate the effects of bulk flow pulsations on film cooling with compound angle holes. A row of five film cooling holes is considered with orientation angles of 0°, 30°, 60°, and 90° at a fixed inclination angle of 35°. Static pressure pulsations are produced by an array of six rotating shutter blades, which extend across the span of the exit of the wind tunnel test section. The pulsation frequency is fixed at 36 Hz, but changes in the time-averaged blowing ratios of 0.5, 1.0 and 2.0 produce three different coolant Strouhal numbers, 3.6, 1.8 and 0.9, respectively. Detailed film cooled boundary layer temperature distributions are measured by a cold wire and the adiabatic film cooling effectiveness by thermochromic liquid crystal (TLC). The boundary layer temperature surveys show that pulsations induce large disruptions to the boundary layer temperature distribution and the film coverage. As the orientation angle increases, the injectant concentration spreads further into the spanwise direction because of pulsations than the steady case. With pulsations the adiabatic film cooling effectiveness value decreases regardless of the orientation angle. The amount of reduction, however, depends on the orientation angle in such a way that the larger the orientation angle is, the smaller the reduction is.     

The Michigan benchmark: towards XML query performance diagnostics

We propose a micro-benchmark for XML data management to aid engineers in designing improved XML processing engines. This benchmark is inherently different from application-level benchmarks, which are designed to help users choose between alternative products. We primarily attempt to capture the rich variety of data structures and distributions possible in XML, and to isolate their effects, without imitating any particular application. The benchmark specifies a single data set against which carefully specified queries can be used to evaluate system performance for XML data with various characteristics.     

氢化非晶硅磷掺杂工艺条件的研究

本文对氧化非晶硅磷掺杂的工艺条件进行了研究，得出掺磷氢化非晶硅的电导率随衬底温度、气体流量、气体压力、射频功率、淀积时间的变化关系，为非晶硅的有效掺杂和器件研究提供了依据。     

Analysis and design of synchronous permanent-magnet planar motors

The force equation of a synchronous permanent-magnet planar motor (SPMPM) was investigated. The flux density distribution of a two-dimensional (2-D) magnet array for a SPMPM was obtained by solving the equations of the scalar magnetic potential. The expressions of the force and back-EMF constant were derived and examined. Using these expressions, the conditions for normal operation of the SPMPM were found and the optimal design was determined in order to maximize the force of the SPMPM.     

关于CEA混凝土膨胀剂的若干技术问题--与游宝坤同志讨论

作者阐述了CEA膨胀剂混凝土的膨胀量较大，干缩小，抗裂性能良好的特性，CEA与粉煤灰掺用提高强度，改善界面过渡层的性质，提高耐久性；CEA混凝土无Ca（OH）2溶出问题。文中列出GBJ119应用技术规范，说明CEA可用于防水工程。     

Thermomechanical fatigue—damage mechanisms and mechanism-based life prediction methods

An existing extensive database on the isothermal and thermomechanical fatigue behaviour of high-temperature titanium alloy EVII 834 and dispersoid-strengthened aluminum alloy X8019 in SiC particle-reinforced as well as unreinv conditions was used to evaluate both the adaptability of fracture mechanics approaches to TMF and the resulting predictive capabilities of determining material life by crack propagation consideration. Selection of the correct microstructural concepts was emphasised and these concepts were, then adjusted by using data from independent experiments in order to avoid any sort of fitting. It is shown that the cyclic /-integral (δJ_eff concept) is suitable to predict the cyclic lifetime for conditions where the total crack propagation rate is approximately identical to pure fatigue crack growth velocity. In the case that crack propagation is strongly affected by creep, the creep-fatigue damage parameter δ_CF introduced by Riedel can be successfully applied. If environmental effects are very pronounced, the accelerating influence of corrosion on fatigue crack propagation can no longer implicitly be taken into account in the fatigue crack growth law. Instead, a linear combination of the crack growth rate contributions from plain fatigue (determined in vacuum) and from environmental attack is assumed and found to yield a satisfactory prediction, if the relevant corrosion process is taken into account.