Pack cementation process for the formation of refractory metal modified aluminide coatings on nickel-base superalloys

The vapour phase compositions of a series of pack powder mixtures containing elemental Al and Hf or W powders as depositing sources and CrCl₃·6H₂O or AlF₃or CrF₃as activators were analysed in an attempt to further develop the pack cementation process to codeposit Al and Hf or W to form diffusion coatings on nickel base superalloys. The results suggested that Al could be codeposited with Hf, but not with W, from the vapour phase. Compared with both AlF₃and CrF₃, CrCl₃·6H₂O has been shown to be a more suitable activator for codepositing Al with Hf. The optimum coating temperature was identified to be in the range of 1050°C to 1150°C. Based on the thermochemical analysis, a series of coating deposition studies were undertaken, which confirmed that codeposition of Al and Hf could be achieved at a deposition temperature of 1100°C in the CrCl₃·6H₂O activated packs containing elemental Al and Hf powders. The coating obtained had a multilayer structure consisting of a Ni₇Hf₆Al₁₆top layer and a NiAl layer underneath, followed by a diffusion zone, which revealed that the coating was formed by the outward Ni diffusion. It is suggested that the compositions suitable for codeposition of Al and Hf could be effectively identified by comparing the vapour pressures of HfCl₄and HfCl₃with that of AlCl in the packs activated by chloride salts. It has also been experimentally demonstrated that, although W could not be deposited from the vapour phase, a high volume of fine W particles can be entrapped into the outer NiAl coating layer formed by the outward Ni diffusion using a modified pack configuration. This leads to the formation of a composite coating layer with W particles evenly distributed in a matrix of NiAl. It is suggested that this modified pack process could be similarly applied to develop nickel aluminide coatings containing other refractory metals that may not be codeposited with Al from the vapour phase.     

Asymptotic performance of single parity-check product codes

This article investigates the asymptotic performance of single parity-check (SPC) product codes (PCs) from a decoding point of view. Specifically, the probability of bit error is bounded before and after the decoding of each dimension, similar to the analysis of "iterated codes" by Elias (1954). It is shown that the asymptotic probability of bit error can be driven to zero as the number of dimensions, and hence the block length, increases at signal-to-noise ratios (SNRs) within 2 dB of capacity over the additive white Gaussian noise (AWGN) channel.     

Analysis of the Scattering Characteristic of Several Waveguide Components Using Boundary Element Method

Several kinds of waveguide components such as curved waveguide bends, arbitrary angle waveguide bends and T-junctions have been analyzed with boundary element method in this paper. A new discretization method for the boundary element method to solve the waveguide discontinuities has been given. The numerical results obtained agree well with the experimental results and numerical results in other literature. Especially, the scattering characteristics of Forded E-, H-plane T-junctions in 3mm band have been analyzed using boundary element method and the calculation results are presented.     

Protecting local access telecommunications networks: Toward a minimum-cost solution

The problem of designing fibre-optic networks for local-access telecommunications generates (at least) three non-trivial subproblems. In the first of these subproblems one must determine how many fibre-optic cables (fibres) are required at either end of a street. In the next subproblem a minimum-cost network must be designed to support the fibres. The network must also provide distinct paths from either end of the street to the central exchange(s). Finally, the fibre-optic cables must be placed in protective covers. These covers are available in a number of different sizes, allowing some flexibility when covering each section of the network. In this paper we describe a dynamic programming (DP) formulation for finding a minimum-cost (protective) covering for the network (the third of the subproblems). This problem is a generalised set covering problem with side constraints and is further complicated by the introduction of fixed and variable welding costs. The DP formulation selects covers along each arc (in the network), but cannot exactly model the fixed costs and so does not guarantee optimality. We also describe an integer programming (IP) formulation for assessing the quality of the DP solutions. The cost of the networks constructed by the IP model is less than those designed using the DP model, but the saving is not significant for the problems examined (less than 0.1%). This indicates that the DP model will generally give very good solutions. Furthermore, as the problem dimensions grow, DP gives significantly better solution times than IP.     

Supermedia-enhanced Internet-based telerobotics

This paper introduces new planning and control methods for supermedia-enhanced real-time telerobotic operations via the Internet. Supermedia is the collection of video, audio, haptic information, temperature, and other sensory feedback. However, when the communication medium used, such as the Internet, introduces random communication time delay, several challenges and difficulties arise. Most importantly, random communication delay causes instability, loss of transparency, and desynchronization in real-time closed-loop telerobotic systems. Due to the complexity and diversity of such systems, the first challenge is to develop a general and efficient modeling and analysis tool. This paper proposes the use of Petri net modeling to capture the concurrency and complexity of Internet-based teleoperation. Combined with the event-based planning and control method, it also provides an efficient analysis and design tool to study the stability, transparency, and synchronization of such systems. In addition, the concepts of event transparency and event synchronization are introduced and analyzed. This modeling and control method has been applied to the design of several supermedia-enhanced Internet-based telerobotic systems, including the bilateral control of mobile robots and mobile manipulators. These systems have been experimentally implemented in three sites test bed consisting of robotic laboratories in the USA, Hong Kong, and Japan. The experimental results have verified the theoretical development and further demonstrated the stability, event transparency, and event synchronization of the systems.     

TEM Studies of High Temperature Corrosion Behaviour of TiAl Intermetallics with Surface Modifications

The oxidation/sulphidation behaviour of a Ti‐46.7Al‐1.9W‐0.5Si alloy with a TiAl₃ diffusion coating was studied in an environment of H₂/H₂S/H₂O at 850^oC. The kinetic results demonstrate that the TiAl₃ coating significantly increased the high temperature corrosion resistance of Ti‐46.7Al‐1.9W‐0.5Si. The SEM, EDX, XRD and TEM analysis reveals that the formation of an Al₂O₃ scale on the surface of the TiAl₃‐coated sample was responsible for the enhancement of the corroison resistance. The Ti‐46.7Al‐1.9W‐0.5Si alloy was also modified by Nb ion implantation. The Nb ion implanted and as received sampels were subjected to cyclic oxidation in an open air at 800^oC. The Nb ion implantation not only increased the oxidation resistance but also substantially improved the adhesion of scale to the substrate.