A general framework for debugging

The state of the art of debugging is examined. A debugged process model that serves as the basis of a general debugging framework is described. The relationship of the model to traditional debugging processes and support tools is discussed. A minimal set of requirements for a general debugging framework is described in terms of both the theory behind debugging methodologies and the support tools. An execution monitor, Eden, that serves as a debugging tool within this general framework is described     

Preparation of flexible polyhedral particles via concentrated emulsion templating polymerization

This paper presents recent efforts on the preparation of flexible polyhedral particles via concentrated emulsion templating polymerization in which the hydrophilic monomer (acrylamide) and hydrophobic monomer (butyl acrylate) are polymerized simultaneously in the continuous and dispersed phase, respectively. Such templating polymerization has been enhanced in our systems owing to the introduction of acrylamide monomer and their higher polymerization rate in continuous phase as compared with butyl acrylate in dispersed phase. Diffusion between the different phases was also inhibited. Furthermore, the stability of the concentrated emulsion and the molecular weight of the produced poly(butyl acrylate) were found to be significantly affected by the amount of redox initiator. The morphology of the particles could be controlled by varying the volume fraction of the dispersed phase and the polyhedral particles were achieved at higher volume fraction. Copyright © 2005 Society of Chemical Industry     

High-strain-rate superplasticity of nanocrystalline aluminum alloy 1570

The structure and mechanical properties of nanocrystalline aluminum alloy 1570 obtained by means of severe plastic deformation have been studied. Being tested in a temperature range from 300 to 400°C, the alloy exhibits high-strain-rate superplasticity. At 400°C, the superplasticity is manifested in a very broad range of strain rates, extending from 5 × 10^?3 to 1 s^?1.     

Host/guest complex of Me-β-CD/2,2-dimethoxy-2-phenyl acetophenone for initiation of aqueous photopolymerization: Kinetics and mechanism

Methylated-β-cyclodextrin (Me-β-CD) was used to complex the photoinitiator, 2,2-dimethoxy-2-phenyl acetophenone (DMPA), yielding a water-soluble host/guest complex. The comparative studies demonstrated that the Me-β-CD complexed DMPA exhibited a high photoreactivity identical to the uncomplexed DMPA, while the CD complex obviously influenced the products of primary photolysis of DMPA and the photopolymerization kinetics due to the steric effect of CD on the subsequent initiation reactions. The photopolymerization rate of acrylamide can be described by the equation: R_p=K[2a]^0.62[M]^1.37[I]^0.5[Me-β-CD]⁰. The mechanism of polymerization was also discussed.     

SU-8 3D microoptic components fabricated by inclined UV lithography in water

Out-of-plane microlenses and microoptical fiber holder are two of the most important components for building an integrated microoptic system with a precise alignment accuracy. In this paper, a simple and convenient method to fabricate these components from SU-8 by using inclined UV lithography in water is proposed. It consists of two perpendicular exposures in SU-8 at ±45°. DI water possesses a low absorption coefficient and a moderate and stable value of refractive index in near UV. Using water, the exposure angle in SU-8 can be increased to 50° from 35° in air necessary to pattern the desired 45° slope of the sidewalls. The principle of the proposed technique and the detailed fabrication process of the microoptic components will be presented. The integratability of the fabricated components was demonstrated by the fabrication of the microoptical fiber holder with a pre-aligned out-of-plane microlens.     

调整水量法(代用法)测定水泥标准稠度用水量方法的改进

结合兰州市的水泥标准稠度用水量方法测定 (代用法 )的实例 ,分析代用法测定标准稠度用水量的缺点 ,并对此方法提出了一些改进措施     

风管摩擦阻力的直接计算方法

提出用高精度的反映密度、黏度和温度关系的经验公式和Colebrook公式计算风管摩擦阻力系数的方法。分析和算例表明，用该方法计算，计算结果比采用常用工程设计方法更为准确，为应用计算机进行风道设计提供了直接、简便的方法。