全耗尽CMOS／SOI技术的研究进展

ＳＯＩ材料技术的成熟，为功耗低，抗干扰能力强，集成度高，速度快的ＣＭＯＳ／ＳＯＩ器件的研制提供了条件，分析比较了ＣＭＯＳ／ＳＯＩ器件与体硅器件的差异，介绍了国外薄膜全耗尽ＳＯＩ技术的发展和北京大学微电子所的研究成果。     

The preparation and magnetic properties of Fe-Ag granular solid using a sol-gel method

The Fe-Ag granular metal solid samples with 10% and 30% weight iron have been successfully fabricated using a sol-gel method, which are characterized by X-ray diffraction and transmission electron micrography. The average diameters of iron particles are from about a few nanometres to a few tens of nanometres controlled by the reducing temperature. The evolution of magnetic properties and microstructure during heat treating are described in detail and explained by using the superparamagnetism, single domain and multi domain theories. The magnetic anisotropy of the Fe-Ag granular solid is studied by using the law of approach to saturation. It is found that the magnetic anisotropy constant is in the order of 10⁵ J m^–3 which is higher than the value of the bulk iron and increases with the increase of reducing temperature.     

小方坯连铸机的PLC自动控制

本文对弧型小方坯连铸机工艺与设备进行了分析，介绍了连铸生产的ＰＬＣ控制系统。及其软件设计。     

复合棒弯曲振动的矩阵解法

按组成材料和横截面大小的不同，把复合棒分成若干单元，每单元两端的位移，截面转角，弯矩以及剪力间的关系用矩阵表示，各单元矩阵相乘即复到复合棒总的矩阵，最后由此求解复合棒的共振条件，以及两端振速比，还给出了应用例。     

Behaviour of Hydrogen in Nano-transition Metals

Nanocrystalline transition metals were prepared with Ar+H2 arc plasma method. The hydrogenmust be used during preparation to get a special nanrvparticles. The hydrogen plays an importantrole in the structure and state of nanocrystalline transition metals. The state of hydrogen andthe change of the nanocrystalline metal structure caused by hydrogen are called the behaviour ofhydrogen in nano-transition metals which includes the ability and function of storing hydrogenin the metals.     

关于不确定的对称组合系统的稳定化控制器与观测器的设计

本文研究了不确定的对称组合系统的稳定化控制器与观测器的设计问题，给出一种设计稳定化控制器与观测器的方法，在这种设计方法中，使给定的带有不确定性的对称组合系统稳定的状态反馈增益矩阵和观测器增益矩阵可由低阶代数Ｒｉｃｃａｔｉ方程的解导出。     

简化源项计算方法

利用程序包STCP估算核电厂在发生严重事故情况下释放到环境的放射性源项需要耗费大量计算机时间和费用。所以,对所有感兴趣的事故情景完成源项程序包的计算实际上是不可能的。为此,发展了一个简化源项计算方法。它的基本思想如下:首先利用STCP计算几个选择的序列,然后根据放射性释放和事故进程的特点处理和分析由STCP计算得到的结果,得出一些特定参数,其它事故序列的源项能够通过这些参数的重新组合得到。     

Fracture of Aramid Fiber/Epoxy Resin Micro Composites

Kevlar-49 fiber was modified through cold air plasma treatment and plasma grafting with acrylic monomers. Fracture of aramid fiber/epoxy resin micro composites has been studied by means of single fiber pull-out test. Tow types of pull-out curves are correlated with the different failure modes. A polyacrylic acid-co-ethyl acrylate graft layer can improve the adhesion and protect the fiber from damage caused by interfacial stresses.     

一种碳－碳复合材料长寿命防氧化涂层的失效机制

用液相法联合ＣＶＤ法和硅化法制备了一种碳－碳复合材料复合梯度涂层，在此基础上对这种涂层在氧化过程中的失效机制进行了研究．结果表明：氧化层与液相层界面反应生成的气相产物是涂层失效的根本原因界面上气泡的不均匀形核、长大和破裂导致涂层表面出现孔洞．孔洞处气泡优先形核、长大和破裂并发展成为缺陷而使涂层失效     

ANALYSIS ON ROOM TEMPERATURE TENSILE STRENGTH OF δ-Al_2O_3, FIBER / Al-12Si COMPOSITE

对δ－Ａｌ２Ｏ３纤维／Ａｌ－１２Ｓｉ复合材料室温拉伸强度的分析表明，在实验条件下该复合材料存在δ－Ａｌ２Ｏ３纤维的最小体积分数Ｖｍｉｎ和临界体积分数Ｖｃｒｉｔ，并求出其基体强度δｍ和室温强度σｃ－δ－Ａｌ２Ｏ３纤维体积分数Ｖｆ直线方程及纤维的临界长度ｌｃ和复合材料的剪切应力τＰ确定复合材料的ＲＯＭ预测曲线，应首先判断σｍ是否等于未增强合金的强度σｕｍ才能得出正确的结论。