Fabrication of barium titanate ceramics via digital light processing 3D printing by using high refractive index monomer

A digital light processing (DLP) technology has been developed for 3D printing lead-free barium titanate (BTO) piezoelectric ceramics. By comparing the curing and rheological properties of slurries with different photosensitive monomer, a high refractive index monomer acryloyl morpholine (ACMO) was chosen, and a design and preparation method of BTO slurry with high solid content, low viscosity and high curing ability was proposed. By further selecting the printing parameters, the single-layer exposure time was reduced and the forming efficiency has been greatly improved. Sintered specimens were obtained after a nitrogen-air double-step debinding and furnace sintering process, and the BTO ceramics fabricated with 80 wt% slurry shows the highest relative density (95.32 %) and piezoelectric constant (168.1 pC/N). Furthermore, complex-structured BTO ceramics were prepared, impregnated by epoxy resin and finally assembly made into hydrophones, which has significance for the future design and manufacture of piezoelectric ceramic-based composites that used in functional devices.     

煤矸石粉/聚酯纤维沥青混合料盐冻损伤研究EI北大核心CSCD

针对煤矸石粉替代率50%、聚酯纤维掺量0.4%的沥青混合料,开展盐冻耦合作用(NaCl溶液质量分数为0%、7.0%、13.0%、26.5%,冻融循环次数为0、2、4、6、8)下的半圆弯曲(SCB)试验,分析了盐冻耦合作用对SCB试件内部损伤劣化过程的影响.结果表明:NaCl溶液质量分数为13.0%、冻融循环为8次时,盐冻耦合作用对沥青混合料的侵蚀破坏作用最强,试件内部损伤最严重;在煤矸石粉与矿粉质量比为1∶1、聚酯纤维掺量为0.4%的条件下,沥青混合料能够形成高黏性、致密、厚实的沥青膜以及由纤维形成的三维网状结构,从而显著降低盐冻侵蚀对沥青混合料的损伤.通过Poly2D模型对SCB试件的极限拉应力损伤量进行拟合,拟合系数为0.944.     

Optical design of the Lyman alpha based beam emission spectroscopy(LAB)diagnostic on the HL-2A tokamak

In this article, we present the optical design of a novel diagnostic on the HL-2 A tokamak, i.e. the20-channel edge Lyman-alpha beam emission spectroscopy, which is a promising solution for edge density turbulence research on tokamaks, as it offers the possibility of density fluctuation measurement with a 3.3 mm spatial resolution while maintains a high temporal resolution of1 μs. The optical path, including the reflective collection optics, the high-dispersion spectrometer, and the linear detector array, is carefully optimized to obtain a good image quality and a high throughput. The maximum root mean square radius of the collection optics is 64 μm.The detected photon flux is estimated to be about 10~(11) photons/s/channel.     

Facile preparation and strong adhesive strength of honeycomb polyurethane films with small pore diameter

With the continuous development of bionics, such as, geckos and virginia creeper with both superhydrophobic and super-adhesive, the surface wetting and super-adhesive properties of various porous materials have attracted extensive attention of the scientific and medical communities. Here, the honeycomb polyurethane (PU) porous films with strong adhesion were successfully prepared by microphase separation method and the effects of growth parameters on their microstructure and adhesive strength to ice were investigated. It was found that a high relative humidity (e.g., 100%) and a low solution concentration (e.g., 2%) facilitated the formation of ordered honeycomb PU porous films, and as-prepared PU pores with average pore diameter as small as 5 μm are better ordered and more uniform than these in related documents. Although the contact angle of water droplets on the surface of PU porous films increased from the premodification value of 85–130° to more than 160° after surface modification with polydopamine (PDA), the corresponding rolling angle remained approximately constant (180°), indicating that the surface of PU porous films has strong adhesion similar to geckos and virginia creeper. Furthermore, at lower temperature, the PU porous films exhibited the high adhesive strength of 142.13 kPa on ice, which was strongly dependent on the porous microstructures and surface compositions. The improved adhesive behavior to ice of honeycomb PU porous films modified with PDA provides new strategies for surface modification of materials and potential applications in medical domain.     

传统牦牛酸奶源高产胞外多糖乳酸菌特性及发酵性能

为了研究四川藏区传统牦牛酸奶中高产胞外多糖乳酸菌特性及发酵性能，以本实验室分离出的六株高产胞外多糖乳酸菌为研究对象，以菌株生长量、耐酸性、胆盐耐受力、渗透压耐受力和细胞表面疏水性为指标进行特性研究；以发酵酸奶的凝乳时间、持水力、酸化及后酸化能力、挥发性物质及质构等为指标进行发酵性能研究。菌株的生长曲线表明，6株菌株分别在14 h（218、276、266）、16 h（271、285、231）进入对数生长稳定期，其中编号218的菌株生长量最高，OD值为2.188。耐受性实验结果表明，菌株276具有良好的耐酸能力（P<0.05）；菌株266、218、231耐胆盐的能力较强；6株菌株均具有较好的耐渗透压的能力，其中菌株285对高渗透压的耐受性较强；菌株285和218在两种有机试剂中的疏水性均显著（P<0.05）高于其他菌株，且与十六烷的结合效果较好。发酵试验结果表明，6株菌株所发酵酸奶均在6~8 h内凝固，酸乳在冷藏期间，活菌数均保持在107 CFU/mL以上，均符合发酵剂的标准，其中菌株276的最高为3.22×106 CFU/mL；菌株218发酵制得的酸奶质构特性较好，持水力和酸化能力较其余菌株均最强，分别为60.98%和83 °T；菌株276、266抗后酸化能力较好；菌株231产香性能最优，乙醛含量为24~26 μg/mL，双乙酰含量为1.58~3.73 μg/mL，能够明显改善酸奶的风味。通过综合比较6株高产胞外多糖乳酸菌特性及发酵性能，菌株218为一株性能良好、具有良好稳定性的菌株，可作为乳酸菌发酵剂且具有一定的应用潜力。研究为利用四川藏区传统牦牛酸奶中分离出的高产胞外多糖乳酸菌在发酵乳制品的应用提供理论依据。     

基于慕课堂数据的学生学习行为分析

本文结合慕课堂线上学习数据与线下考试成绩,研究学生在线学习的行为表现与学习效果之间的关联性,所获得的信息能够体现出不同学生群体的特点以及不同学习维度的作用,从而提醒教师适时调整教学策略,持续改进,有助于教师改进教学方法,提高教学质量.