�¸�������в������Ȼ�����꾮�ٶȵ�;��

本文针对天然气井提高钻井速度问题,总结分析了盆地中部井身结构,水力、机械参数,聚合物钻井液,正注反挤固井等工艺技术对该地区钻速的影响。指出提高天然气井钻井速度,必须搞好系统工程,形成配套技术。     

^60Coγ射线对刚地弓形虫缓殖子感染性的影响

应用不同剂量的~(60)Coγ射线照射含NT株弓形虫包囊的鼠脑匀浆后,以0.4％胰蛋白酶液消化,使弓形虫缓殖子从包囊中释放出来,并用生理盐水作连续10倍稀释,使成为含不同数量缓殖子的悬液,将此悬液接种小鼠,用生物检测方法确定其感染性。另设未经照射处理的缓殖子悬液感染小鼠的对照组。结果表明,γ射线0.55kGy剂量为控制鼠脑中NT株弓形虫感染性的最小有效剂量。γ射线0.1kGy剂量对弓形虫缓殖子感染性无明显影响,而0.45kGy照射后,其感染性较前者下降了10~4倍。     

包钢氟污染治理成效及对策

本文介绍了包钢历年来氟污染治理成效以及控制外排氟总量达标的具体措施.     

GaAlInP发光材料计算的经验公式

根据已经发表的实验数据，针对镓铝铟磷发光材料的提出了一组经验公式及相应的曲线，作为ＧａＡｌＩｎＰ可见光材料设计的依据或参考。     

Influences of artificial pre-stressing on ply stresses and tensile properties of Vinylon fibre-reinforced aluminium laminates (VIRALL)

A simple micromechanical model based primarily upon the rule-of-mixtures is developed which allows prediction of the effects of fibre preload on the ply stresses (i.e., the initial residual stresses of fibre, adhesive and matrix) induced within VIRALL laminates, and the tensile stress-strain curves and mechanical properties of VIRALL laminates. The analysis of the ply stresses of VIRALL laminates indicates that pre-stressing will dramatically influence the ply stresses. The predicted tensile stress-strain curves of VIRALL laminates are in good agreement with the experimental curves and the results show that the stress-strain curves of VIRALL laminates move upwards when the prestress increases. The predicted tensile mechanical properties of VIRALL laminates at room temperature show good agreement with those obtained experimentally; both show that prestress can improve the tensile properties (i.e., elastic limit strength, 0.2% yield strength and failure strength) of VIRALL laminates.     

析出物对IF钢性能的影响

一种阻性的晶闸管控制制动器被用于阻尼向串联补偿传输供电的热电发电机中的瞬态扭。重点放在开发适用的控制算，并通过多种不同的运行方式验证算法。作为一种制动器最优控制的可能方法，本文研究了离散等级一般化预先控制（ＧＰＣ），讨论了系统上ＧＰＣ执行过程中存在一些问题。用Ｐｒｏｎｇ分析来辩识系统传递函数，此传递函数与控制方案的考虑及强度特性有关。     

The relationship between serum lipids, apolipoproteins level and bile lipids level, chemical type of stone

To pick up serum high risk lithogenic factors predisposing one to gallstone formation and protective factors against gallstone formation in gallbladder. We compared serum lipid and apolipoprotein level of patients with gallbladder stone (stone group) with that of patients without gallbladder stone (control group). The correlation between serum lipid, apolipoprotein level and bile lipid level, cholesterol saturated index (CSI), characteristics of lipidemia in different kinds of gallbladder stones were studied. The results showed that the increase of serum Apo A1, C2 and E level in the stone group was more significant than in the control group. But there was no statistical significance in TC, TG, LDL-C, HDL-C, Apo A2, B, C3 level between the stone and control groups. These results suggested that serum apolipoproteins perhaps are more sensitive parameters than serum lipids in distinguishing patients with stones from those without stones. There were different profiles of serum lipid and apolipoproteins in different chemical types of gallbladder stones. Increased level in serum LDL-C, Apo B and ratio of LDL-C/HDL-C were characterized by an index for cholesterol stone, otherwise that in serum TG and Apo C2 an index for pigment stones. There was a positive correlation between serum total cholesterol (TC) or Apo B, C2, C3 and cholesterol amount or CSI in gallbladder bile. Therefore, TC, Apo B, C2, C3 could be considered as high risk lithogenic factors. A positive correlation existed between serum HDL-C and lecithin in gallbladder or common bile duct (CBD) bile as well as between HDL-C and bile acids in CBD bile. Thus, HDL-C might be a protective factor against gallstone formation in gallbladder.     

集群移动通信系统的组网设计

本文对集群移动通信系统在组网设计时应考虑的问题进行了分析，并提出了具体步骤和方法，可供集群系统组网设计时参考。     

A comprehensive approach to the solution of direct-coupledmultislice model of skewed rotor induction motors using time-steppingeddy-current finite element method

Normally a complicated three-dimensional (3-D) approach is needed to study the field pattern of induction machines with skewed rotor bars. In this paper, a time-stepping two-dimensional (2-D) eddy-current finite element method, based on multislice technique, is described to study the steady-state operation and the starting process of skewed rotor induction machines. The fields of the multislices are being solved en bloc simultaneously, and thus, the effects of the eddy current and saturation can be taken into account directly. New forms of the governing equations for the multislice model are derived, which allow the meshes of multislices to be taken as one 2-D mesh so that the algorithm is very similar to that of general 2-D problems. Special techniques required for the mesh generation in the multislice model and the salient structures of the software are also described. The results obtained by using the program being developed have very good correlation with test data