过程控制级模拟轧钢系统的研制及在热轧试车中的应用

宝钢集团上海第一钢铁有限公司(后面简称一钢)新建的不锈钢工程1780热轧项目中,为了能在较短周期内完成所有的应用软件开发与测试任务,特别研制了模拟轧钢功能。本论文主要阐述利用计算机的集成思想,结合热轧工艺,来开发模拟轧钢功能,以及利用模拟轧钢进行现场各种情况的模拟测试。     

Compatibility between Polyamide 6 and Polycarbonate

Polyamide （PA6） and polycarbonate （PC） were prepared by a Brabender mixer （ PLV- 151） at 240℃ with 30 rpm for duration of 8 and 6 minutes respectively. The epoxy resin （E） addition can lead to substantial microstructural changes in the PA6/PC blends. Scanning electron microscope （SEM） was used to observe the mixtures characterized by the domains of clearly segregated homophases and voids between the two polymers. PA6/PC of polyamide 6 and polycarbonate with epoxy resin addition under the composition ratio of 20/80, 20/80/1, 40/60/1 and 40/60, were tested to verify the key role of epoxy in promoting the compatibility of PA6 with PC during blending.     

Matlab软件在分形几何上的应用

以Koch曲线和塞尔平斯基三角形为例,介绍了Ma tlab软件在分形几何方面,对不规则图形进行直观描绘的方法。     

杀菌剂异螺环-4-烯-2,3-5''''-氯-吲哚的合成

研究了以薯蓣皂素(diosgenin)为原料,根据活性叠加原理,在分子中引入一个新的活性基团吲哚环,合成了全新化合物异螺环-4-烯-2,3-5'-氯-吲哚.杀菌药效试验结果表明:所设计的全新目标化合物具有原料所没有的杀菌活性.     

浅谈电梯选型应注意的问题

电梯选型配置问题是个十分有实际意义的话题。本文结合作者多年来检测检验电梯的经验，浅谈几点选型配置应注意的问题。     

压力铸造的现状与发展

概述了压力铸造技术的特点，总结了目前中国压铸与国外的差距，分析了我国压铸业面临的机遇和挑战，论述了压力铸造技术的新工艺，以及今后压力铸造的研发方向。     

Design of the ECRH/ECCD Launcher System for HL-2A Tokamak

An ECRH/ECCD system with two 68GHz/500kW/1S gyrotrons will be built up in HL-2A tokamak. The location of the Gaussian beam waist is 580 mm away from the center of the plasmas and the beam radius is 37 mm at the center of the plasmas. Compared to the minor plasma radius （420 mm）, it is small enough for localized control. The launcher system covers a wide toroidal and poloidal steering range by the two steering plane mirrors. Therefore it is possible to explore the on- and off-axis heating over half of the plasma minor cross section and the co-current drive.     

溶液温度对电化学沉积氧化亚铜薄膜相成分和显微结构的影响

用电化学方法在不锈钢基体上沉积多晶Ｃｕ２Ｏ薄膜并用Ｘ射线衍射和扫描电进行了分析研究了溶液温度对薄膜相组成、晶粒尺寸和择优取向的影响，当溶液的ＰＨ＝９，温度低于５０℃时得到的是Ｃｕ２Ｏ／Ｃｕ复相薄膜，纯Ｃｕ２Ｏ薄膜可在溶液温度高于５０℃时获得，纯Ｃｕ２Ｏ薄膜具有（１００）择优取向，实验发现薄膜的晶粒尺寸随溶液温度的增加从０．１２μｍ增加到０．６５μｍ。     

电阻衰减匹配网络的设计计算法

声频系统,不管是播出系统还是节目制作系统,都是由为数不少的声频设备相互连接而成。设备之间的配置是否合理,直接影响节目制作的质量。由于现在我们使用的设备,规格繁多,性能各异,要把这些不同的输出阻抗和输入阻抗、相差甚远的输出电平和输入灵敏度合理地配接起来,既要使系统稳定可靠地输出,又要满足主要技术指标(频响、失真度和信噪比)的规定要求,级间的衰减、匹配是很重要的一环。     

Numerical Simulation of Independent Advance of Ore Breaking in the Non-pillar Sublevel Caving Method

The mechanism of stress generation and propagation by detonation loading in five separate independent advance of ore breaking patterns is discussed in the paper. An elastic numerical model was developed using AN- SYS/LS-DYNA 3D Nonlinear Dynamic Finite Element Software. In this package ANSYS is the preprocessor and LS-DYNA is the postprocessor. Numerical models in the paper to actual were l：10 and the element mesh was dissected in scanning mode utilizing the symmetry characteristics of the numerical model. Five different advance rates were studied. Parameters, such as the time required to maximum stress, the action time of the available stress, the maximum velocity of the nodes, the stress penetration time, the magnitude of the stress peak and the time duration for high stress were numerically simulated. The 2.2 m advance appeared optimum from an analysis of the simulation results. The results from numerical simulation have been validated by tests with physical models.