强化两相混合的超临界技术制备聚乳酸微粒

针对商品化聚乳酸微球粒径分布较宽难于适用气溶胶给药要求的不足,采用水力空化混合强化超临界流体辅助雾化技术(SAA-HCM)制备聚乳酸(PLA)超细微粒.该技术主要特点是通过在超临界流体和液相进料处引入水力空化混合器,强化两相间的混合.考察SAA-HCM过程混合器压力、温度、沉淀器温度、进料中CO2与液体溶液质量流量比和溶液质量浓度等操作参数对微粒形态和粒径分布的影响,成功制备出球形度较好,粒径分布较窄(1～3μm)的PLA微球.经X射线衍射(XRD)分析和差示扫描量热(DSC)分析显示,与原料PLA相比,微球晶型及热曲线变化不大,但结晶度下降.同时把操作参数与相行为进行关联,探讨了影响颗粒形貌的机理.对比超临界流体辅助雾化法(SAA)的实验结果表明:水力空化的引入能有效强化混合器内的两相传质,混合更好,能制备出适用于气溶胶给药要求的超细微粒.     

Optimization of uncertain acoustic metamaterial with Helmholtz resonators based on interval model

Uncertainties existing in the acoustic metamaterial may strongly affect its unusual properties. Aiming at this actuality, the interval model is introduced to treat with uncertainties existing in the acoustic metamaterial with Helmholtz resonators. Frequency intervals in which the sound intensity transmission coefficients are certainly less than the required value and the effective bulk moduli are certainly negative are defined as conservative approximations. Frequency intervals in which the sound intensity transmission coefficients may be less than the required value and the effective bulk moduli may be negative are defined as unsafe approximations. The proportion of the conservative approximation and the unsafe approximation is defined as an approximate precision. Based on the quantification of uncertainties of the sound intensity transmission coefficients and the negative effective bulk moduli, an optimization model for the interval acoustic metamaterial with Helmholtz resonators is constructed. Numerical results showed that even suffering from effects of interval parameters, unusual properties of the optimized acoustic metamaterial (such as the bandgap of the sound transmission and the negative effective bulk modulus) could be improved.     

电控柴油机分缸均衡控制算法及试验

柴油机各个气缸的进气量、喷油量、燃烧等存在差异,导致气缸间存在做功差异,直接影响柴油机转速的平稳性以及排放性能等。针对位置式电控柴油机,采用PI闭环控制,通过瞬时转速信号识别并计算各缸的工作差异,利用分缸均衡控制算法对油量进行补偿修正。试验结果显示低转速稳态工况转速波动由7 r/min降至3 r/min,各缸工作不均匀度由±5 r/min降至±2 r/min,在瞬态过程和高转速3 400 r/min时该算法仍然适用有效。     

介质阻挡放电反应器降解邻二甲苯的特性研究

采用介质阻挡放电(DBD)降解常压下流动态的邻二甲苯模拟废气,系统地考察了放电极值电压,气体的初始质量浓度、停留时间以及相对湿度等工艺参数对邻二甲苯降解的影响,并初步探讨了邻二甲苯的降解产物.实验研究结果表明:在7.0kV的放电极间电压下,邻二甲苯的初始质量浓度为1 500mg/m3,停留时间为9s,其去除率可达到80%以上.降解产物主要为CO2、H2O以及苯甲酸、苯乙酸、苯乙醛等有机物,并且经降解后产物的生物可生化性得到提高,因而为后续的等离子-生物法联合处理VOCs提供了依据.     

导磁体在汽车零件感应加热中的应用技术

本文简单介绍了导磁体工作的基本原理，并给出在汽车零件大规模生产中所积累的导磁体应用的一些经验，以阐明如何更有效地使用导磁体。     

Oxidation Performance of Fe-Al/WC Composite Coatings Produced by High Velocity Arc Sprayed at 650 ℃

Fe-Al intermetallics with remarkable high-temperatureintensity and excellent erosion,high-temperatureoxidation and sulfuration resistance are potential lowcost high-temperature structural material.ProducingFe-Al/WC composite coating by high velocity arcspraying(HVAS)on structural materials would notonly obviate the problems faced in fabrication of thesealloys into useful shapes,but also allow the effectiveuse of their outstanding high-temperature performance,which might thus promisingly mak…     

金属材料屈服强度的应变率效应和热激活理论

对４种金属材料进行了应变率为１０＾－４－１０＾３ｓ＾－１的拉伸试验，结果表明，屈服中度随应变率的升高分两阶段线性升高，提出了位错线热振动对加载频率的响应的热激活作用机理，依据该机理计算所得Ⅰ，Ⅱ区临界应变εｃ与实测值相符，并在此基础上将应变率对掘强度影响的机制图重新划分为：Ｉ区，富热激活区；Ⅱ区，贫热激活区。     

数控机床的可靠性分析

从不同侧面分析了数控机床的可靠性,阐述了提高数控机床可靠性的方法。