Corrosion behaviour of copper-reinforced carbon electrodes in dilute hydrochloric acid solutions

The corrosion behaviour of experimentally prepared copper-reinforced carbon electrodes in dilute hydrochloric acid is investigated. The electrodes are not only directly attacked by the acid, but they are also subjected to galvanic corrosion. The baking temperature and time are the most crucial processing variables. A minimum in the corrosion rate is always achieved when the electrodes are baked at 400 °C for 1.5 h, the level depending on the copper content. The corrosion resistance increases progressively with the baking temperature as long as the baking time is less than 1.5 h. Baking for more than 1.5 h results in increasing corrosion rate. The presence of copper increases the corrosion resistance of the prepared electrodes.     

Water and salt permeability of reinforcement polymer‐gel composite membrane

The charged mosaic polymer membrane (CMM) without reinforcement and the composite charged mosaic polymer membrane (CCMM) with reinforcement were investigated in terms of salt and water transport (permeability). The composite charged mosaic polymer membrane (CCMM) with reinforcement showed a unique transport behavior such as preferential material transport L_p and ω. Water permeability coefficient, L_p and salt permeability coefficient, ω were estimated by taking account of active layer thickness of composite polymer gel. The L_p and ω values of CCMM with reinforcement were larger than those of CMM without reinforcement. On the other hand, the reflection coefficient of CCMM, σ, showed negative value, which suggested preferential material transport to solvent transport. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Improvement of the engineering properties of asphalt pavements using a ‘soft’ compaction technique (AMIR-Compaction)

In most countries of the world asphalt pavement of road networks represents the biggest single investment in the transportation system. In Canada, asphalt pavement built over the past decade is worth more than 70 billion dollars (in 1984 dollars). In order to maintain the current road network at the present level of service and prevent it from further deterioration, over 6 billion dollars is needed anually.

Traditionally, asphalt overlays are widely used to rehabilitate existing deteriorated pavements. Unfortunately the new overlays have been observed to fail in a relatively short time. Thus the investment in overlays is lost.

Recent research based on the concept of relative rigidity has indicated that the rapid deterioration of new asphalt overlays is directly related to current construction equipment. It has been shown analytically and experimentally that steel rollers used in compacting the asphalt layer will result in surface cracks during construction. Traffic and environmental influences will accelerate the failure of the new layer.

This paper presents the results of a testing programme evaluating the engineering properties of asphalt slabs compacted by a new method using a compactor termed AMIR. The results showed that the AMIR compactor will prevent the formation of constitution cracks resulting in an increase of indirect tensile strength of 10% and an increase of direct tensile strength of up to 60% when compared to steel roller compacted asphalt slabs.     

Effects of Solvent Exchange Period and Heat Treatment on Physical and Chemical Properties of Rice Husk Derived Silica Aerogels

In this study, hydrophobic silica aerogels were synthesized from rice husk ash-derived sodium silicate through sol-gel processing, solvent exchange, surface modification and ambient pressure drying. By volume, 10% of trimethylchlorosilane (TMCS) in 90% of n-hexane was used as a hydrophobic solution in the surface modification process. The physical and chemical properties of silica aerogels were characterized by density and porosity measurements, scanning electron microscopy (SEM), Fourier transforms infrared (FTIR) spectroscopy, Brunauer–Emmett–Teller theory (BET) and dynamic scanning calorimetry (DSC). The hydrogels prepared were in the form of 2.5 ± 0.5 mm beads and then converted into alcogels through solvent exchange with ethanol for repetition of 3, 6 and 9 days. It is found that the optimal quality of silica aerogels with the BET surface area as high as 668.82 m²/g was obtained from the alcogels of the solvent exchange period of 9 days. Depending on the size of the gel’s block, a longer solvent exchange period will ensure adequate removal of pore water. Post heat treatment on silica aerogels obtained from the 9 days of solvent exchange at 200, 300 and 400 °C for 2 h results in slight decreased of aerogel’s density from 0.048 g/cm³ to 0.039 g/cm³ and the hydrophobicity of the aerogels is decreased above 380 °C as confirmed by DSC analysis.

     

Irradiation of poly(vinyl chloride) with H2 plasma. II

Poly(vinyl chloride) films blended with plasticizers, stabilizers, and fillers are irradiated with a beam of H₂ plasma. The polymer partially loses its solubility in cyclohexanone. The viscosity of the soluble part decreases in the initial stages and then increases on further irradiation. Crosslinking was followed by dehydrochlorination and discoloration of the polymer. The electrical conductivity was measured as a function of the irradiation dose and time. The plasticizers enhanced the action of plasma while the stabilizers and fillers reduced it.     

Structural material from waste plastic

In efforts to contribute to community development, particularly in the context of Egyptian communities, waste plastics materials were successfully recycled without the difficult task of separation and reused to economically produce new structural material. Recycling was performed by mixing molten waste plastics with sand to produce these new materials. Samples with different percentages of plastics and different particle sizes of sand were used in the process. Materials showed acceptable density and high compressive strength, which was shown to be at a maximum with contents of about 30–40% waste plastic. Furthermore, certain types of sand having different colors were used to produce attractive materials, suitable for decorative uses. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 2543–2547, 2004     

Physicochemical properties of irradiated and loaded LDPE films with polyfunctional monomers

Polyfunctional monomers (PFMs), namely, trimethylol propane trimethacrylate (TMPTMA), trimethylol propane triacrylate, ethylene glycol dimethacrylate, and diethylene glycol diacrylate were blended with low‐density polyethylene (LDPE) and exposed to different doses of EB irradiation. Fourier transform infrared and ultraviolet and UV–vis spectroscopy of the unirradiated, irradiated, unloaded, and PFMs‐loaded LDPE films were studied under various irradiation doses up to 300 kGy. The degree of crosslinking and oxidative degradation, as measured by the spectroscopic parameters, were dependent on both the irradiation dose and the type of loaded PFMs. For all of the loaded monomers, the extent of crosslinking increased at different rates as a function of irradiation dose. TMPTMA monomer was the most efficient in enhancing the crosslinking of LDPE films compared to the other loaded monomers. However, the unloaded LDPE film showed the least extent of crosslinking. In addition, the EB‐radiation‐induced changes, such as trans‐vinylene formation, a decrease in vinyl and vinylidene unsaturation; and carbonyl double‐bond formation and change in crystallinity were correlated. The importance of these results on the prediction of the role of polyfunctional monomers in the production of crosslinked polymers is discussed. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2025–2035, 2003     

Dynamic mechanical properties of agricultural residues‐filled polystyrene

Agricultural residues (cotton straw) were added as very small particles to polystyrene (PS) at different weight ratios by using a melt‐mixing technique. The dynamic mechanical tests were performed over a wide range of temperatures and frequencies by using an ARES rheometer (Rheometrics Scientific) operated in the dynamic mode. The dynamic mechanical properties in terms of the storage modulus (G′), loss modulus (G″), compliance moduli, loss tangent, and dynamic viscosity were studied and compared for PS and PS composite. The results showed that the dynamic mechanical moduli and viscosity were found to increase with the addition of cotton straw and rise further with its loading increasing. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 37–40, 2004     

Pentavalent vanadium ion–cellulose thiocarbonate redox-system induced grafting of methyl methacrylate and other vinyl monomers onto cotton fabric

Cellulose thiocarbonate was prepared by reacting cotton cellulose fabric with carbon disulphide in the presence of sodium hydroxide. The treated fabric formed, with pentavalent vanadium ion, an effective redox system capable of initiating grafting of methyl methacrylate (MMA) and other monomers no+o the cotton fabric. The dependence of grafting on vanadium concentration, pH of the polymerization medium, temperature and duration of grafting, nature and concentration of monomer, and solvent/water ratio was studied. The results indicated that increasing the pentavalent vanadium (V^v) concentration up to 60 mmol/L was accompanied by enhancement in the rate of grafting; the latter was not affected by further increase in V^v concentration. Maximum grafting yield was achieved at pH 2; grafting fell greatly at higher pH. The rate of grafting followed the order: 70° > 60° > 50°C. The graft yield increased significantly by increasing the MMA concentration from 0.5 to 5%. Of the solvents studied, n-propanol and isopropanol enhanced the grafting rate provided that a solvent/water ratio of 5 : 95 was used; a higher solvent ratio decreased the magnitude of grafting. Other solvents, namely, methanol, ethanol, n-butanol, and acetone, in any proportion, decreased the rate of grafting. With the monomer used, the graft yield followed the order: methyl methacrylate > methyl acrylate > methacrylic acid > ethyl methacrylate > acrylic acid. Also reported was a tentative mechanism for vinyl-graft copolymerization onto cotton fabric using cellulose thiocarbonate-V^v. © 1993 John Wiley & Sons, Inc.     

Fourier transform infrared (FTIR) authentication and batch-to-batch consistency for different types of paints using benchtop and handheld FTIR spectrophotometers for oil and gas industry

Standardization of Fourier transform infrared (FTIR) fingerprint region for paints and assessment on the reproducibility using different spectrophotometers were investigated. While selective fingerprint regions may be confusing for technicians/analysts who are non-chemists, we attempt to generalize these regions (e.g., 1300–1000 cm⁻¹ for Epoxy part A and 1400–1000 cm⁻¹ for Epoxy part B) by choosing a universal region (2000–900 cm⁻¹) that works for different paints. Comparison result using a paired student t-test shows that the degree of similarity (r) values from the studied regions are not statistically different. The paint fails the screening analysis occasionally on-site when analyzed using handheld FTIR due to the higher level of noise that gives low r values (r < 0.900 ± 0.002). The same samples were analyzed using a benchtop FTIR and the r values are above 0.900 ± 0.002. While the screening may lead to a false rejection of the sample on-site, there could be occurrence of false acceptance. The on-site screening of EPZ part A with different formulations, for instance, shows that the r values over the entire IR spectrum are above 0.900 ± 0.002 when analyzed using handheld FTIR. After the samples were analyzed using the benchtop, the r values fall below 0.900 ± 0.002.