Sintered stainless steels: Fatigue crack propagation resistance under hydrogen charging conditions

Monophasic and multiphasic (two and three phases) sintered stainless steels were prepared both considering premixes of AISI 316LHC and AISI 434LHC stainless steels powders and using a prealloyed duplex stainless steel 25% Cr, 5% Ni, 2% Mo powder. Their fatigue crack propagation resistance was investigated both in air and under hydrogen charging conditions (0.5 M H₂SO₄ + 0.01 M KSCN aqueous solution; applied potential = −700 mV/SCE), considering three different stress ratios (R = 0.1; 0.5; 0.75). Fatigue crack propagation micromechanisms were investigated by means of fracture surface scanning electron microscope (SEM) analysis.For all the investigated sintered stainless, fatigue crack propagation resistance is influenced by hydrogen charging and an increase of crack growth rates dependent on the steel microstructure is obtained. Experimental results also allow to identify the sintered stainless steel obtained from the prealloyed 25% Cr, 5% Ni, 2% Mo powder as the most resistant to fatigue crack propagation in air and under hydrogen charging conditions.     

First-Principles Investigation of the Interfacial Stability,Precipitate Formation,and Mechanical Behavior of Al3Li/Al3Zr/Al Interfaces

Metallurgical and Materials Transactions A - Precipitates including Al3Li, Al3Zr and core–shell structured Al3Li (Al3Zr) produce significant strengthening effects in Al-Li alloys by means of...     

离心成型法制备Al2O3/Ni功能梯度材料及性能表征

用离心成型法制备了Al2O3/Ni功能梯度材料,并研究了料浆调制工艺、制备参数和梯度材料的力学性能.结果表明,良好的料浆的最佳流动性配比为粘结剂(聚乙二醇)含量为2 mass%、固相含量为63 vol.%、球磨时间为36 h.经离心成型-真空烧结(1400℃,2 h)可获得致密、组元宏观连续过渡的Al2O3/Ni梯度材料.该复合材料孔隙率低,力学性能好,抗弯强度可达321 MPa.     

试论大型汽车覆盖件模具制造调试的途径

针对汽车大型覆盖件零件的工艺特点，采用先进的模拟仿真技术、测量技术、调试技术、逆向工程技术，探索出了一条汽车大型覆盖件模具制造调试的途径。     

我国型钢生产技术进步20年及展望

按小型材、棒线材、中型材、轨梁和大型材分类 ,对 2 0年来我国在型钢生产领域的主要技术进步进行了总结 ,对其生产现状进行了分析 ,对其发展前景进行了展望     

Effects of Austempering after Hot Deformation on the Mechanical Properties of Hot Rolled Si-Mn TRIP Steel Sheets

Excellent mechanical properties are obtained by austempering after hot deformation without subsequent heat treatment in the present Si-Mn TRIP steel sheets. Isothermal holding time after finishing rolling has affected the mechanical properties of this steel. The results show that the sample exhibits a good combination of ultimate tensile strength and total elongation when it is held at the bainite transformation temperature after hot deformation. The stability of retained austenite increases with an increase of isothermal holding time, and a further increase in the holding duration results in a decrease of it. The tensile strength, total elongation and strength ductility reach the maximum values (774MPa, 33% and 25542MPa% respectively) for this sort of hot rolled Si-Mn TRIP steel using the optimal technology.     

活性石灰/粉煤灰制备烧结烟气脱硫剂配比试验研究

本文研究了以钢铁企业常用物料活性石灰和自备电厂粉煤灰制备的脱硫剂,在循环流化床脱硫试验装置上进行了烧结烟气脱硫剂配比试验.试验结果表明,活性石灰与粉煤灰的质量比按1:2配置时,脱硫剂钙的利用率较高,具有较好的经济性.     

Model of intense pulsed ion beam and simulation study of energy deposited on target

Gaussian type models have been established according to the real detected voltage of magnetically insulated ion diode and intense pulsed ion beam density near the focus of the diode. The energy deposition of Al target irradiated by intense pulsed ion beam has been simulated by Monte Carlo method based on these models. The results of energy depositions of the irradiation of single energy ions and the Gaussian distribution IPIB have been obtained. Especially cases of ion beam irradiating Al target at different angles on one dimension and two dimensions are discussed. The evolution processes of the energy deposition of ions in target have been simulated during a pulse. In addition, incident angles of H⁺ ions and C⁺ ions ranging from 20 to 40° have been researched. We obtained the conclusions that C⁺ ions of the beam affect the physical properties of near surface region, but H⁺ ions affect the deeper layer. The energy of intense pulsed ion beam mainly deposits on target surface, so melting and evaporation begin both from target surface.     

使用人工神经网络对强力旋压有限元模拟进行参数预选

在筒形件强力旋压领域内，介绍了使用人工神经网络的手段，在MARC有限元模拟的前处理中实现参数预选的方法。作为与有限元模拟相结合的旋压智能化设计的一项关键技术，能够达到减少有限元模拟的误差和工作量的目的。