机动武器系统的含间隙动力学研究--下篇:系统仿真

本文把中篇建立的间隙铰模型引入多体系统动力学分析中,得到了一种处理含间隙多体系统动力学问题的一般方法.应用这种方法对机动武器的发射过程进行了原理性的仿真,验证了前面建立的碰撞模型和间隙模型,并分析了间隙对导弹运动状态的影响.导弹发射过程具有变拓扑的特点,本文方法提供了一种处理这类问题的思路.     

用硫酸铁铵容量法测定钛精矿中二氧化钛含量

样品在过氧化钠熔融、水浸取及盐酸酸化后，在盐酸和硫酸介质中，隔绝空气，用金属铝将钛(Ⅳ)还原至钛(Ⅲ)，以硫氰酸盐为指示剂，用硫酸铁铵标准溶液滴定。     

首钢外购焦炭质量恶化后的高炉生产实践

针对焦炭质量劣化的状况，高炉操作以活跃炉缸为主，从上下部调剂入手，采取疏导煤气、控制合理的实际风速和鼓风动能、缓解焦炭在高温区的粉化等措施，有效地改善了高炉的顺行状况，并逐步恢复高炉指标。     

硼酸铝晶须增强环氧树脂和双马来酰亚胺树脂体系的研究

本文以硼酸铝晶须为增强剂，以4，5-环氧环己烷-1，2-二甲酸二缩水甘油酯(TDE-85)，甲基纳狄克酸酐(MNA)、N，N’-二胺基二苯甲烷型双马来酰亚胺(BMI)/O，O′-二烯丙基双酚A(BA)体系分别作为基体制备晶须增强复合材料。研究了晶须对树脂的尺寸、表面处理方法、含量对树脂体系力学性能和热性能的影响；通过扫描电子显微镜(SEM)分析了浇注体的弯曲、冲击断口，研究晶须的增强机理。     

尿素解吸废液及甲醇残液联合处理工艺的应用

安阳化学工业集团公司(以下简称安化集团)现有2套200 kt/a尿素装置及1套60 kt/a甲醇装置.尿素及甲醇装置在生产过程中会产生大量的尿素解吸废液和甲醇残液,废液中的氨氮(NH3-N)含量和化学需氧量(CODCr)较高,给该公司废水的达标排放带来很大压力.     

卫生陶瓷贴牌（OEM）加工问题的探讨

前言 近20年来,随着改革开放和国民经济的飞速发展,我国建筑卫生陶瓷行业也得到快速发展,产量连年增长,成为世界上建筑卫生陶瓷的最大生产国和消费国,也是出口大国.2007年全国卫生陶瓷的产量达到15 000万件,占世界产量的40%,出口量达到5 525万件,占产量的40%.     

椭圆型偏微分方程的加法Schwarz方法

1.引 言 古典加法Schwarz方法(ASM)对于一般问题收敛很慢,在大多数情况下, ASM只能作为预条件子.另一方面,ASM的并行性能非常好,尤其适合大规模粗粒度并行计算,近年来随着并行机系统及并行计算的兴起,ASM重新受到重视.许多学者研究了怎样提高ASM的收敛速度[1,2,4].他们发现加法Schwarz方法之所以收敛慢是由于在内边界上采用     

Cooling and Solidification of Melted Drops in an Immiscible Cooling Medium

The cooling and solidification of melted drops during their movement in an immiscible cooling medium is widely employed for granulation in the chemical industry, and a study of these processes to provides a basis for the design of the granulation tower height and the temperature of the cooling medium is reported. A physical model of the cooling and solidification of the drop is established and the numerical calculation is performed. The influences of the key factors in the solidification, i.e., Bi number, drop diameter, temperature of the cooling medium, etc. are presented. The cooling and solidification during wax granulation in a water‐cooling tower and during urea granulation in an air‐cooling tower (spraying tower) are described in detail. Characteristics of the solidification and temperature distribution within the particle at different times are shown. The model and calculations can be used for structure design of the granulation tower and optimization of the operation parameters.     

Facile modifications of polyimide via chloromethylation: II. Synthesis and characterization of thermocurable transparent polyimide having methylene acrylate side groups

From chloromethylated polyimide, a useful starting material for modification of aromatic polyimides, a thermocurable transparent polyimide having acrylate side groups was prepared. In the presence of 1,8‐diazabicyclo[5,4,0]undec‐7‐ene, chloromethylated polyimide was esterified with acrylic acid to synthesize poly(imide methylene acrylate). The polymer was soluble in organic solvent, which makes it possible to prepare a planar film by spin coating. The polymer film became insoluble after thermal treatment at 230 °C for 30 min. Optical transparency of the film at 400 nm (for 1 µm thickness) was higher than 98 % and not affected by further heating at 230 °C for 250 min. Adhesion properties measured by the ASTM D3359‐B method ranged from 4B to 5B. Preliminary results of planarization testing showed a high degree of planarization (DOP) value (>0.53). These properties demonstrate that poly(imide methylene acrylate) could be utilized as a thermocurable transparent material in fabricating display devices such as TFT‐LCD. Copyright © 2004 Society of Chemical Industry     

Further study on the cooling correction in bomb calorimetry: Theoretical aspects of approximate formulae

On the basis of the compensation of errors it is postulated that the most accurate correction may not always give the most accurate result for calorific value, and experimental evidence for this is presented. A new criterion is therefore suggested for judging the best (not necessarily the most accurate) cooling correction. Using this principle the cooling correction formula previously proposed is improved which results in higher accuracy whilst retaining the original simplicity.