A high-current and high-temperature 6H-SiC thyristor

A 6H-SiC thyristor has been fabricated and characterized. A forward breakover voltage close to 100 V and a pulse switched current density of 5200 A/cm² have been demonstrated. The thyristor is shown to operate under pulse gate triggering for turn-on and turn-off, with a rise time of 43 ns and a fall time of less than 100 ns. The forward breakover voltage is found to decrease by only 4% when the operating temperature is increased from room temperature to 300°C. It is found that anode ohmic contact resistance dominates the device forward drop at high current densities     

各种状态的液体通过核孔膜的规律

介绍了液体通过核孔膜规律方面取得的新认识，包括：（１）纯净液体通过核孔膜的规律；（２）核孔膜测定液体粘滞系数的各种方法；（３）各种物质溶液浓度的核孔膜测定；（４）液相混合物快速分离和化学分离；（５）流体中固体微粒对核孔膜的堵塞及其公式；（６）用核孔膜滤除液中各各斩规律。     

The effects of plasma etching induced gate oxide degradation onMOSFET's 1/f noise

The effects of the plasma etching process induced gate oxide damages on device's low frequency noise behavior are investigated on MOSFET's fabricated with different field plate perimeter to gate area ratio antennas. Abnormal 1/f noise spectrum with a shoulder centered in the frequency range of 100 and to 1 kHz was frequently observed in small geometry devices, and it is attributable to a nonuniform distribution of oxide traps induced by plasma etching process     

COIL中BHP浓度对发生O_2(~1△)的影响

本文实验研究了BHP的浓度对产生O2（1△）的影响。实验结果表明：当BHP浓度大于3.5M时，Cl2利用率以及O2（1△）的产率将不依赖于BHP浓度的变化而变化，同时，实验结果表明，使用低浓度的BHP对COIL的操作是可行的。     

层状催化剂颗粒的优化设计——双组分等温平行反应体系

针对双组分等温平行反应体系,分析讨论了以提高催化剂活性和选择性为目标时催化剂活性组分的最优分布形式(为δ-函数分布),并给出了确定这种反应体系的催化剂的最佳活性层位置的计算方法。结果表明:以提高选择性为目标的最佳活性层位置比以提高活性为目标的要更靠近催化剂核心,实用的最优位置应介于二者之间。最后,本文还研究了反应动力学级数、本性选择性以及内扩散模数(Thiele 模数)等因素对最佳活性层位置的影响。     

我的家

我生于东京的银座,那是个靠近传统花街柳巷、歌舞升平的地方,在童年的记忆里那里随时随地都是一片华美景象。而在这些景象的背后有一排排美丽的临街二层长屋建筑,大都是料亭,还有颇有风致的砖结构剧场。那时父母在这里经营着咖啡馆,街上的行人总是把店里挤得满满的。数年前父亲     

Orientation in uniaxially stretched plasticized atactic polystyrene

Summary Fourier transform infrared spectroscopy and birefringence measurements have been used to study the changes in molecular orientation which occur on drawing of plasticized as compared to pure polystyrene (PS) at a temperature T=Tg+Cte. No influence of plasticizers on orientation can be detected whatever the interactions between small molecules and PS chains are. Comparison with previous results obtained on PS-poly(vinylmethyl ether) compatible blends confirms the importance of the macromolecular nature of the second component to enhance the friction coefficient leading to higher level of chain orientation.