三聚甲醛萃取—精馏新工艺及过程优化

本文对采用Ｓ１和Ｓ２的混合物作为萃取剂的三聚甲醛萃取－精馏新工艺进行了模拟计算，得到了使总费用最低的三聚甲醛精制工艺的联合操作参数。模拟计算结果成功地指导了小试操作，并可为大型工程设计提供可靠的基础数据。     

Growth and characterization of hot-wall epitaxial CdTe on (111) HgCdTe and CdZnTe substrates

Thin CdTe films were deposited by hot-wall epitaxy (HWE) on (111) HgCdTe and CdZnTe substrates at temperatures from about 140 to 335°C. X-ray rocking curves were used to show that crystal quality of the CdTe (111)B films improved as substrate temperature increased from 140 to about 250°C. Rocking curve values for full width at half maximum (FWHM) decreased from 2–4 degrees at 140–150°C to less than 100 arc-s at 250°C, and a FWHM of 59 arc-s was the lowest value observed near 250°C. The FWHM of the HWE CdTe was found to be insensitive to growth rate below about 400Å/min, but increased to four degrees at 1250Å/min. X-ray diffraction confirmed that films grown on the B-face at higher temperatures were epitaxial, but contained a significant volume fraction, 35% to 50%, of rotational in-plane twins. Electron microscopy confirmed a coarse twin density, and photoluminescence spectra showed an absence of excitonic emission in the HWE films. Simultaneous growth on two (111) HgCdTe substrates with different surface polarities between 230°C and 335°C showed that deposition rate on the A-face decreased relative to that on the B-face as temperature increased. Films grown on the B-face exhibited better surface morphologies than those grown on the A-face.     

哈尔滨炼油厂MTBE装置试生产

介绍了哈尔滨炼油厂ＭＴＢＥ装置的工艺路线、新技术的应用及特点；催化剂的装填及应用情况；总结了生产过程中遇到的一系列问题及解决办法；探索了平稳生产的新徐径，以保证装置安全、平稳、长周期运行；同时对反应器操作温度、催化蒸馏塔操作压力、原料中醇烯比等因素对异丁烯转化率及ＭＴＢＥ产品的影响做了简单的总结。     

Catalytic behavior of YBa2Cu3O7-x in the partial oxidation of methanol to formaldehyde

The partial oxidation of methanol to formaldehyde was studied over YBa₂Cu₃O_7-x catalyst in a flow reactor. The structural change of YBa₂Cu₃O_7-x before and after the reaction was measured by means of XRD and iodometric titration method. The catalytic characteristics of YBa₂Cu₃O_7-x for the partial oxidation of methanol to formaldehyde was due to copper ions. It was found that Cu⁺² was responsible for the higher selectivity for formaldehyde.     

Abrasive wear of dental composite resins

Abrasive wear is a major problem in the application of dental composite resins. In this study the friction and wear behaviours of two types of dental composites: one containing relatively coarse filler particles and some microfillers (Estilux) and another containing only microfiller particles (Durafill), have been investigated by using a scratch testing machine. Experimental results show that the coefficients of friction in both composites are essentially constant for applied loads up to 20 N. The wear resistance of Durafill is better than Estilux. Under the same testing conditions, the size, shape and distribution of the filler particles are more important variables than applied load and sliding speed in controlling the wear mechanism. It is shown that for Estilux, plastic ploughing by the diamond indenter is the predominant mechanism. For Durafill, however, the formation and propagation of tensile cracks on the worn surface is the main wear mechanism. The effects of two different indenters, diamond and enamel, on the basic wear mechanisms are also discussed.     

太钢4号高炉喷煤站应用MFD—Ⅲ型布袋除尘器的实践

太钢４号高炉喷煤站从１９９０年起采用ＭＦＤ－Ⅲ型脉动反吹式布袋除尘器。这种除尘器采用脉动式反吹清灰设施，合理布置布袋间距，布袋支撑骨架及选用针呢材质的布袋，过滤面积大，反吹清灰效果好，设备运行平稳，除尘效率高达９９．８％，排放浓度小于１０ｍｇ／ｍ＾３，故障率低。     

The trans-syn-I thymine dimer bends DNA by approximately 22 degrees and unwinds DNA by approximately 15 degrees

Chromium metabolism of lactating women was evaluated by measuring diet, breast milk, urine, and serum chromium in 17 subjects 60 d postpartum. Breast milk chromium concentration was similar for the 3 d of collection with a mean +/- SE concentration of 3.54 +/- 0.40 nmol/L (0.18 ng/mL). Dietary intake and urinary chromium values were also similar for each of the 3 collection days. Total chromium intake of lactating mothers (0.79 +/- 0.08 mumol/d) was greater than that of reference female subjects (0.48 +/- 0.02). There was a significant correlation (r = 0.84) between serum chromium and urinary chromium excretion. If a breast milk volume of 715 mL is assumed, chromium intake of exclusively breast-fed infants is < 2% of the estimated safe and adequate daily intake of 10 micrograms. In summary, breast milk chromium content is independent of dietary chromium intake and serum or urinary chromium values. Chromium intake also did not correlate with serum or urine chromium but there was a significant relationship between serum and urinary chromium concentrations.     

Pullout tests of epoxy-coated reinforcement in concrete

The bond strength and slip of epoxy-coated reinforcing bars in concrete have been evaluated by carrying out single pullout and double pullout tests. In extended single pullout tests, slip measurements were made while tensile force was applied to reinforcing bars embedded in concrete. In double pullout tests, 20 cycles of load were applied at levels of steel stress between zero and 0·5 times characteristic steel strength. Strains were measured by electrical resistance strain gauges glued inside the bars. Both epoxy-coated and uncoated bars were used in the investigation, to obtain comparative results. The strain gradient along the bar was found to be less for the coated reinforcement. In general, the epoxy coating was found to increase slip in bond and thereby reduce the bond performance of coated bars.