Single-Crystalline TiO2(B) Nanobelts with Unusual Large Exposed {100} Facets and Enhanced Li-Storage Capacity

The {100} facet of single-crystalline TiO₂(B) is an ideal platform for inserting Li ions, but it is hard to be obtained due to its high surface energy. Here, the single-crystalline TiO₂(B) nanobelts from H₂Ti₃O₇ with nearly 70% {100} facets exposed are synthesized, which significantly enhances Li-storage capacity. The first-principle calculations demonstrate an ab in-plane 2D diffusion through the exposed {100} facets. As a consequence, the nanobelts can significantly accommodate Li ions in LiTiO₂ formula with specific capacity up to 335 mAh g⁻¹, which is in good agreement with the electrochemical characterizations. Coating with conductive and protective poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate), the cut-off discharge voltage is as low as 0.5 V, leading to a capacity of 160.7 mAh g⁻¹ after 1500 cycles with a retention rate of 66% at 1C. This work provides a practical strategy to increase the Li-ion capacity and cycle stability by tailoring the crystal orientation and nanostructures.     

Comparative studies on thermal and toughness properties of polybenzoxazine composites with two functionalized graphene oxides

Abstract

Graphene oxide (GO) was functionalized by polyether amine (PEA) via two methods which were one-pot modification in acetone (GON) and two steps with the intermediate product of GOCO-Cl generated (GONS). There were more PEA successfully grafted onto GO for GONS than GON. The onset polymerization temperatures of the benzoxazine (Bz) composites decreased by the inclusion of 1?wt% of GO, GON or GONS. Thermal stability of the polybenzoxazine (PBz) composites was significantly improved indicated from the increase of weight loss temperature. T₁₀, T₂₀ and T₅₀ values of the composites with GONS were higher than that of the others. Toughness of PBzs may be enhanced by the incorporation of nanofillers, and GONS had stronger interfacial interaction with PBz matrix than GON.     

马钢张庄矿高压辊磨机装配工艺研究

针对马钢张庄矿高压辊磨机辊套疲劳断裂严重、对辊精度不能满足生产要求等问题，马钢重机公司根据张庄矿实际生产要求对对辊进行国产化，国产化内容包括辊轴、辊套等零部件的新制以及装配工艺攻关，通过技术研发同时结合实际生产经验，成功对高压辊磨机辊套与辊轴以及辊轴与轴承进行装配，完成了张庄矿高压辊磨机整对对辊的国产化，为该型设备后续生产及优化提供了理论和实践参考依据。     

氯甲烷在镁修饰的ZSM-5分子筛催化剂上催化转化研究

在镁修饰的ZSM-5分子筛催化剂上,氯甲烷可以被催化转化为烃类产品。分别采用了离子交换和浸渍的方法来修饰ZSM-5分子筛。离子交换的Mg-ZSM-5催化剂和浸渍的Mg/ZSM-5催化剂都可以提高反应产物中的低碳烯烃的选择性,降低烷烃的选择性,并且保持较高的反应活性,但高的浸渍量对反应活性有一定的影响。NH3-TPD的结果表明,浸渍镁的ZSM-5催化剂的强酸中心数目明显减少。镁的修饰对催化剂酸性的影响导致了产物中低碳烯烃的增加。浸渍Mg的ZSM-5催化剂是潜在氯甲烷转化生成低碳烯烃的催化剂。     

Growth Defects in Langasite Crystals Observed with White Beam Synchrotron Radiation Topography

Langasite single crystal was grown by the Czochralski method and its perfection was assessed by white beam synchrotron radiation topography. It is found that the growth core and the growth striations are the primary growth defects and they show strong X-ray kinematical contrast in the topographs. Another typical defect in LGS crystal is dislocation. The formation mechanisms of these growth defects in LGS crystals were discussed.     

人工颅骨用复合材料中微量甲基丙烯酸甲酯的气相色谱法测定

采用氢气焰离子化检测器(FID),以正丁醇为外标物,PEG-20M为固定相,甲醇作为溶剂,气相色谱法测定复合材料人工颅骨中微量MMA的含量。其相对标准偏差<0.022,平均回收率(n=4)为98.0％～99.1％。此方法操作简便,用于实际样品分析可得到满意的结果。     

Zk线性码的对称形式的MacWilliams恒等式

该文定义了Zk线性码的码字的对称重量计数公式，利用离散的Hadamard变换，建立了线性码与其对偶码之间的对称形式的MacWilliams恒等式．