Craze yielding and fracture mechanism in PE/PS/PE laminated films

The change in polystyrene (PS) layer thickness, which has been simultaneously determined during post-yield deformation, shows that crazing is the basic mechanism of toughening in all laminated films, and that shear deformation supplements the contribution of crazing especially for samples with high polyethylene (PE) volume fractions. Crazes formed in PS layers in the laminated films are slender and regular compared with the short and lenticular crazes formed in bulk PS film. When PE volume fraction increased, craze advance speed decreased because of the reduction of the stress concentration effect at craze tips. The life-time of the first mature craze to be formed at a given strain rate increased with PE volume fraction because the PE supporting the mature crazes could effectively inhibit craze rupture and blunt out the propagating crack by absorbing the stored elastic energy in the PS layer that would have been dissipated as fracture surface energy.     

Electrical conductivity and gas sensitivity of Zn-Sb-O thick films

The thick film of Zn-Sb-O was prepared by coating the paste of nanoparticles mixture (Sb₂O₃:ZnO=1:3) on the alumina substrate, followed by sintering at 500-900 °C for 2 h in air. The electrical resistance and gas-sensing properties to benzene, alcohol and acetone of Zn-Sb-O films were found to be dependent on the change of phase structure caused by sintering temperature.     

上海外环隧道水下最终接头的施工技术

沉管隧道采用水下最终接头,可以大大缩短工期和减少成本,但施工难度较大,而且有一定风险。文章以上海外环隧道工程为例,对沉管隧道水下最终接头的施工工艺中管段轴线精度控制、安装保护罩、间隙间的安全排水和混凝土施工等四大难点进行探讨,并介绍了水密性施工和管内结构施工的具体工艺和步骤。指出其成果对今后类似工程具有较大的参考价值。     

MIMO系统中简单的扩展空时块编码分集技术研究

本文提出一种多输入多输出（MIMO）天线系统中简单的扩展空时块编码（SSTBC）分集技术，采用沃尔什码来区分各天线发送数据子流。采用这种方法，在系统带宽一定时，不降低发送信息速率，同时接收机简单。不同天线的发送信息经过了所有收一发天线对之间的空间子信道，获得了所有路径的部分空间分集增益，仿真结果表明，这种增益的获得不受限于接收分集阶数，并且随发射天线的增加以一定的线性关系增加。     

组件式GIS在密钥管理系统中的应用

本文讲述了利用组件式GIS技术,在密钥管理系统中进行GIS集成二次开发,实现设备地图技术,为密钥管理系统业务中的保密设备管理提供图形化、可视化支持,并给出了基于组件式GIS的密钥管理系统模型。     

Ultra-wideband bandpass filter with hybrid microstrip/CPW structure

A novel ultra-wideband (UWB) bandpass filter (BPF) is presented using the hybrid microstrip and coplanar waveguide (CPW) structure. A CPW nonuniform resonator or multiple-mode resonator (MMR) is constructed to produce its first three resonant modes occurring around the lower end, center, and higher end of the UWB band. Then, a microstrip/CPW surface-to-surface coupled line is formed and modeled to allocate the enhanced coupling peak around the center of this UWB band, i.e., 6.85GHz. As such, a five-pole UWB BPF is built up and realized with the passband covering the entire UWB band (3.1-10.6GHz). A predicted frequency response is finally verified by the experiment. In addition, the designed UWB filter, with a single resonator, only occupies one full-wavelength in length or 16.9mm.     

Frequency notched printed slot antenna with parasitic open-circuit stub

A new frequency notched ultra-wideband microstrip slot antenna with a parasitic tuning stub is proposed. The antenna is similar in configuration to a conventional microstrip slot antenna; by introducing a parasitic open-circuit tuning stub, flexible frequency notched function is achieved. Several properties of the antenna, such as frequency notched function, antenna transfer function and gain, have been investigated. As is reported, the operation bandwidth of the antenna is 2.91-11.16 GHz, in which a frequency notched band of 5.10-5.85 GHz has been achieved. Furthermore, good ultra-wideband linear transmission performance over the entire operation frequency range has also been achieved.     

Effects of compressive and tensile stress on the growth mode of epitaxial oxide films

Oxide films were deposited on different substrates by laser molecular beam epitaxy. Reflection high-energy electron diffraction was performed to in situ investigate the change of growth mode and the lattice relaxation during the growth. An asymmetrical phenomenon was found in the two kinds of strain states, compressive stress and tensile stress of heterostructures with different lattice mismatch. In the case of BaTiO₃/SrTiO₃ (2.2%), 2D layer-by-layer growth mode without lattice relaxation can be maintained for a longer period for BTO films on STO with compressive stress, comparing to STO films on BTO with tensile stress. When MgO films were deposited on SrTiO₃ with a large mismatch of 7.8%, compressive stress leads to rapid lattice relaxation with a very thin wet layer, and 3D strained island were observed. As a comparison, SrTiO₃ films on MgO with tensile stress were configured. No RHEED patterns can be observed duo to a large tensile stress.     

氩等离子体辐照反相乳液接枝改性涤纶织物的研究

首次提出了在等离子体辐照后再用反相乳液接枝改性涤纶织物的新方法,探讨了接枝颗粒特征以及织物各项物理力学性能.接枝织物的结构及性能的测试结果表明:接枝物的尺寸远小于纤维的直径,在提高织物吸湿性的同时,对织物透气性能和强力等无明显影响;实验也证实了乳液中未接枝单体可以再次聚合.     

两种塑料纸芯管结构与性能比较分析

测试与分析了两种塑料管材的拉伸与弯曲性能、热变形温度、结晶性和化学组成,分析结果表明:管材B较管材A具有更高模量与热变形温度,但管材B较高的分子量与较小的分子量分布抑制管材产品内在的均匀性,且管材B中的α晶在高温下向β晶的转变可能会影响管材长期使用性能.