Effects of Plant Growth Hormones on Mucor indicus Growth and Chitosan and Ethanol Production

The objective of this study was to investigate the effects of indole-3-acetic acid (IAA) and kinetin (KIN) on Mucor indicus growth, cell wall composition, and ethanol production. A semi-synthetic medium, supplemented with 0–5 mg/L hormones, was used for the cultivations (at 32 °C for 48 h). By addition of 1 mg/L of each hormone, the biomass and ethanol yields were increased and decreased, respectively. At higher levels, however, an inverse trend was observed. The glucosamine fraction of the cell wall, as a representative for chitosan, followed similar but sharper changes, compared to the biomass. The highest level was 221% higher than that obtained without hormones. The sum of glucosamine and N-acetyl glucosamine (chitin and chitosan) was noticeably enhanced in the presence of the hormones. Increase of chitosan was accompanied by a decrease in the phosphate content, with the lowest phosphate (0.01 g/g cell wall) being obtained when the chitosan was at the maximum (0.45 g/g cell wall). In conclusion, IAA and KIN significantly enhanced the M. indicus growth and chitosan production, while at the same time decreasing the ethanol yield to some extent. This study shows that plant growth hormones have a high potential for the improvement of fungal chitosan production by M. indicus.     

Two-level distributed clustering routing algorithm based on unequal clusters for large-scale Internet of Things networks

The Journal of Supercomputing - According to the recent advancements in communication technologies and the widespread use of smart devices, our environment can be transforming into the Internet of...     

Hot tensile properties and microstructural evolution of as cast NiTi and NiTiCu shape memory alloys

Hot tensile properties of as cast NiTi and NiTiCu shape memory alloys were investigated by hot tensile test at temperature range of 700–1100 °C using the strain rate of 0.1 s⁻¹. The NiTi alloy exhibited a maximum hot ductility at temperature range of 750–1000 °C, while the NiTiCu alloy showed it at temperature range of 800–1000 °C. It was found that at temperatures less than 750 °C, diffusion-assisted deformation mechanism was inactive leading to semi-brittle type of failure and limited ductility in both alloys. Also it was found that at temperature range of 800–1000 °C, dynamic recrystallization is dominant leading to high ductility. Likewise, the fracture surface of the specimens presenting the maximum hot ductility showed an ideal type of ductile rupture in which they gradually pulled out to a fine point. On the other hand, the decline in ductility occurred at the temperatures above 1000 °C was attributed to the liquid phase formation leading to interdendritic and intergranular type of fracture.     

A Novel 2.5–3.1 GHz Wide-Band Low-Noise Amplifier in 0.18 \upmu \hbox {m} CMOS

Aiming for the simultaneous realization of constant gain, accurate input and output impedance matching and minimum noise figure (NF) over a wide frequency range, the circuit topology and detailed design of wide broadband low noise amplifier (LNA) are presented in this paper. A novel 2.5–3.1 GHz wide-band LNA with unique characteristics has been presented. Its design and layout are done by TSMC 0.18  \(\upmu \hbox {m}\) technology. Common gate stage has been used to improve input matching. In order to enhance output matching and reduce the noise as well, a buffer stage is utilized. Mid-stages which tend to improve the gain and reverse isolation are exploited. The proposed LNA achieves a power gain of 15.9 dB, a NF of 3.5 dB with an input return loss less than \(-\) 11.6, output return loss of \(-\) 19.2 to \(-\) 19 and reverse isolation of \(-\) 38 dB. The LNA consumes 54.6 mW under a supply voltage of 2 V while having some acceptable characteristics.     

Finite element analysis of deformation and fracture of an exploded gas cylinder

This paper presents the finite element simulations of deformation and fracture of a gas cylinder which catastrophically failed as a result of an accidental explosion. The results of a previous detailed investigation of this incident indicated that detonation of a low-pressure oxygen-rich mixture of hydrogen and oxygen was the cause of the cylinder failure. In the current study, the finite element method was used to provide a more realistic modeling of geometry, material behavior, and boundary conditions of the cylinder. The overall transient dynamic response of the cylinder to gaseous detonation loading was studied using the ANSYS/LS-DYNA V10 package and the crack growth simulations were performed using the WARP3D-R15 research code. The crack growth analyses were performed using interface cohesive elements. The finite element results were validated using analytical solutions and data collected from the remains of the cylinder. The simulations clearly showed that the stresses caused by the assumed loading profile were indeed capable of creating local ruptures at the actual crack initiation sites. It was also shown that the self-similar growth of the initial axial crack in the main body of the cylinder was a fatigue-type incremental growth governed by the structural waves. The subsequent cyclic bulging of the crack flaps and the resultant crack curving and branching were also simulated.     

Recycling of aluminium alloy turning scrap via cold pressing and melting with salt flux

Among the various steps of aluminium production from liquid metal, a lot of scrap is generated due to machining operations. Therefore, recycling of aluminium scrap is an interesting subject because of the broad applications of this metal and low efficiency of processes used to recycle metal scrap. In this paper, the recyclability of aluminium alloy AA 336 turnings with different cold compacting pressures and a protective salt flux (NaCl–KCl–KF) has been experimentally studied. Various categories of compacted samples were melted at 750 °C in molten aluminium alloy AA 336 and also in the protective salt flux to recover aluminium alloy. In order to understand the amount of recycling of different samples, weight loss measurement was applied. From recyclability stand point it is shown that using protective salt flux is the best route, from the point of view of recyclability. Mechanical properties and chemical analysis of samples were approximately the same as the primary material produced by conventional casting process.     

Computer simulation of the effect of post annealing parameters on the microstructure inhomogeneity of the non-uniformly deformed copper

A computer simulation on the basis of the Finite Element Method and Monte Carlo Model is developed to simulate the microstructure of the non-uniformly deformed copper workpiece after annealing. Using the computer simulation, the effects of annealing time and temperature on the microstructure inhomogeneity of the workpiece are simulated and investigated quantitatively, by defining an Inhomogeneity Factor, to design an annealing program for reducing the microstructure inhomogeneity. The results show that with increasing the parameters of annealing time and temperature, the inhomogeneity is decreased when one of the parameters is constant. Also, at high annealing temperature, the annealing time changes the inhomogeneity slowly compared with which occurs at low annealing temperature. The simulation results agree well with the experimental values.     

EBIC-guidelines for management of severe head injury in adults. European Brain Injury Consortium

Guidelines for the management of severe head injury in adults as evolved by the European Brain Injury Consortium are presented and discussed. The importance of preventing and treating secondary insults is emphasized and the principles on which treatment is based are reviewed. Guidelines presented are of a pragmatic nature, based on consensus and expert opinion, covering the treatment from accident site to intensive care unit. Specific aspects pertaining to the conduct of clinical trials in head injury are highlighted. The adopted approach is further discussed in relation to other approaches to the development of guidelines, such as evidence based analysis.     

An efficient and regioselective thiocyanation of aromatic and heteroaromatic compounds using cross-linked poly (4-vinylpyridine)-supported thiocyanate as a versatile reagent and potassium peroxydisulfate as a strong oxidizing agent

A green and regioselective thiocyanation of aromatic and heteroaromatic compounds has been achieved via a simple protocol using cross-linked poly (4-vinylpyridine)-supported thiocyanate ion, [P₄-VP]SCN, as a versatile polymeric reagent and potassium persulfate as a strong oxidizing agent, under heterogeneous conditions.

Various indoles, phenol and aniline derivatives, and pyrroles were transformed into their corresponding aryl thiocyanates in high to excellent yields. This procedure offers advantages such as short reaction time, simple reaction work-up, and the polymeric reagents can be regenerated and reused for several times without significant loss of their activity.     

Synthesis of aluminium nanoparticles by arc evaporation of an aluminium cathode surface

Aluminium nanoparticles (Al Nps) are synthesized using arc discharge method by applying direct current between aluminium electrodes in liquid environment without any use of vacuum equipment, heat exchangers, high temperatures furnaces and inert gases. After synthesis of Al Nps, in situ coating process on the nanoparticles was performed immediately. The effects of media on the yield and morphology of aluminium nanoparticles were investigated. Analysis result of the samples indicated that particle size was less than 30 nm, when 120 A/cm² arc current was used. In addition, coating agent can affect arc velocity, arc stability, morphology and composition of the nanoparticles. Resultant nanoparticles were identified using X-ray powder diffraction (XRD), also their surface morphology was studied by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) and finally the accuracy of coating was assessed with infrared (IR) spectroscopy.