瓦斯燃烧器回流区测试

燃烧器流场内回流区的大小和形状决定了燃烧火焰的稳定性 ,利用APV激光测速系统 ,在燃烧器冷态测试实验装置上对一瓦斯燃烧器冷态模型的流动进行了研究 ,发现了该燃烧器流场内的双回流区结构 ,并得到了中心回流区尺寸与稳焰器结构的关系 ,为该结构类型燃烧器的稳焰设计及稳焰能力的评价提供了实验依据     

液晶显示器生产中的激光退火和缺陷修复

由于在大面积玻璃基底上制备由多层材料构成的高质量薄膜晶体管象元驱动阵列工艺的复杂性，使有源矩阵液晶显示器（AMLCD）的成品率低、价格高。利用激光对AMLCD进行非晶硅薄膜的退火和电路缺陷的修复，可有效的改善AMLCD的性能，提高成品率和降低成本。本文在介绍了激光对非晶硅薄膜退火和电路缺陷修复常用激光器的特性后，讨论了激光对不同类型缺陷修复的原理和过程。最后，分析比较了不同类型激光退火方法的特点。     

连续铸造技术的发展概况及展望

回顾国内、国外连续铸造技术的发展概况；指出开发和完善“近终形连铸”、“单晶连铸”、“高效连铸”、“连铸坯热送热装”等技术和基于连铸技术研制新型材料是连铸技术发展的主要方向。     

用变角XPS定量分析研究GaAs光电阴极激活工艺

用变角X射线光电子能谱 (XPS)技术分析了GaAs光电阴极的激活工艺 ,定量计算了阴极表面激活层和界面氧化层的厚度和组成。界面氧化物是由于O原子穿过激活层 ,扩散到GaAs与 (Cs,O)激活层的界面上而形成的。导入过量O会增加O GaAs界面层的厚度 ,而对 (Cs,O)激活层厚度影响较小。在激活过程中 ,严格控制和减少每次导入的O量是减少界面氧化层厚度 ,提高灵敏度的重要途径。在第一步激活后的阴极样品 ,通过较低温度的加热和再激活 ,能获得比第一步高出 30 %的光电灵敏度的原因是较低温度加热减少了界面氧化层的厚度和界面势垒     

生长条件对KDP晶体中散射颗粒的影响

利用透射电子显微技术对不同条件下生长的KDP晶体中包裹物进行了观察并测量了其相应尺寸。结果表明，晶体中的生长缺陷、pH值、生长速度和杂质与KDP晶体散射颗粒的形态存在密切关系。     

Electron-beam controlled switching using quartz and polycrystallineZnS

Results of electron-beam controlled switching experiments with switch samples of quartz crystal and polycrystalline zinc selenide (ZnSe) are presented. For switch samples of both materials, drastic reductions of the switch resistance were induced by the electron beam. The quartz sample showed very fast temporal response (less than 1 ns) with potential applicability for current control. The ZnSe samples, on the other hand, showed longer current transients (on the order of 10 ns) with exponential development of the switch resistance after the electron beam pulse     

YAG：Nd激光照射犬气管粘膜的实验研究

An experimental study for the pathologic changes of the canine tracheal mucosa under YAG:Nd laser ablation was performed in order to master the appropriate parameters for the clinical treatment of YAG:Nd laser. 6 male and female Mongolia dogs weighing 13-18 kg were received 20W YAG:Nd laser treatment and their pathologic changes were examined instantly and 3, 7, 14 and 28 days after ablation.     

Constrained Drying of Aqueous Yttria-Stabilized Zirconia Slurry on a Substrate. I: Drying Mechanism

Aqueous yttria-stabilized zirconia slurry was cast on a substrate to form wet coatings. Both weight loss and thickness reduction were measured, during the drying process. Lateral drying was observed by in situ monitoring of the coating surface. The drying kinetics were classified as an initial constant rate period (CRP), followed by a falling rate period (FRP). Thickness reduction occurred in the CRP stage, and was uneven across the coating because of lateral flow. As tensile stresses developed within the coating because of the constrained volume shrinkage, crack formation and propagation occurred in the FRP stage and affected the drying rate.