电子警务中三维全景技术应用研究

随着信息技术的飞速发展,三维全景技术已成为电子警务中重要的组成部分。本文通过对三维全景技术特点和发展状况的介绍,提出了一套三维全景地理信息系统的应用框架,探讨了三维全景技术应用中的关键技术,并结合电子警务建设实际,详细介绍了三维全景技术在电子警务中的具体应用。可以预测,随着三维全景技术和物联网技术、云计算的集成,未来三维全景技术将成为电子警务的主流技术。     

简析组建互联局域网

随着网络的应用发展普及,用户向信息化发展的必然选择是网络的建设,局域网不仅能使信息能及时、准确地传送给每个用户,并能提供许多种应用服务。局域网组建中主要应用了网络技术中的局域网技术来建设与管理的。     

基于OpenLayers的矿场人员监控系统的研究与设计

矿区工作人员的人身安全问题和工作职责问题一直困扰着用工单位。有没有办法实时监控到矿工,又不用花费太高的成本呢?本文介绍了一种基于OpenLayers、Geoserver、J2EE的矿场人员监控的WebGIS应用的设计。     

铍材应力常数的X射线法测试

在X2001应力分析仪上采用悬臂梁加载法测试了可以用于铍的X射线应力测试的5个衍射晶面的应力常数。结果表明,铍的5个衍射晶面的应力常数差异较大，在进行X射线应力分析时．应采用相应衍射晶面的应力常数，才能获得准确的应力分析结果。由于X射线对铍有较大的穿透深度，必须考虑X射线穿透深度对应力常数标定的影响。     

小型储气罐火灾工况数值模拟分析

以某输气管线气液联动执行机构中的储气罐为例,利用Ansys Fluent软件建立同比例三维模型,模拟火灾工况下,外部热量不断输入,罐内压力和罐体温度随时间的变化情况。利用Aspen Hysys软件模拟计算该小型储气罐在火灾工况下安全泄放所需的最小安全阀口径。结果表明,当钢制储气罐外部发生火灾时,罐体温度和罐内压力急剧升高,在很短的时间内就能达到储气罐坍塌温度和储气罐设计压力;达到钢制储气罐坍塌温度的时间滞后于达到储气罐设计压力的时间;从安全的角度,设置安全阀可安全有效泄放气体,即使储气罐发生坍塌,也有助于降低事故发生的危害程度;确定的安全阀最小口径为0.03 cm²,建议选型的安全阀口径不低于0.05 cm²。     

熔剂净化对Al－4．5wt％Cu合金过冷及组织的影响

采用盐类熔剂对大体积Ａｌ－４．５ｗｔ％Ｃｕ合金进行净化处理，研究了熔剂净化对Ａｌ－４．５ｗｔ％Ｃｕ合金过冷及组织的影响。通过大量的实验研究证明：粘性熔剂更能有效地去除合金中的异质核心，使合金获得较大的过冷度；随着过冷度的增大，合金的宏观组织由细小的等轴晶逐渐过渡到粗大的柱状晶，其临界转变过冷度为４０℃；二次枝晶间距随过冷度的增大而增大，其转变过冷度为５０℃。     

Photocatalytic syngas synthesis from CO2 and H2O using ultrafine CeO2-decorated layered double hydroxide nanosheets under visible-light up to 600 nm

The rational design of photocatalyst that can effectively reduce CO₂ under visible light(l>400 nm),and simultaneously precise control of the products syngas(CO/H2)ratio is highly desirable for the Fischer-Tropsch reaction.In this work,we synthesized a series of CeO₂-decorated layered double hydroxides(LDHs,Ce-x)samples for photocatalytic CO₂ reduction.It was found that the selectivity and productivity of CO and H₂ from photoreduction of CO₂ in conjunction with Ru-complex as photosensitizer performed an obvious“volcano-like”trend,with the highest point at Ce-0.15 and the CO/H₂ ratio can be widely tunable from 1/7.7 to 1/1.3.Furthermore,compared with LDH,Ce-0.15 also drove photocatalytic CO₂ to syngas under 600 nm irradiation.It implied that an optimum amount of CeO₂ modifying LDH promoted the photoreduction of CO₂ to syngas.This report gives the way to fully utilize the rare earth elements and provides a promising route to enhance the photo-response ability and charge injection efficiency of LDH-based photocatalysts in the synthesis of syngas with a tunable ratio under visible light irradiation.     

Importance of Low-Temperature Melt-Mixing on the Construction of Stereocomplex Crystallites with Superior Nucleation Efficiency in Asymmetric Poly(l-lactide)/Poly(d-lactide) Blends

The nucleation efficiency (NE) of stereocomplex crystallites (SCs) formed in asymmetric poly(L-lactide)/poly(D-lactide) (PLLA/PDLA) blends is generally unsatisfactory because the competition between stereocomplexation and chain mixing involved in the melt-mixing process can cause low formation efficiency and even severe aggregation of SCs. Herein, it is attempted to achieve high-efficient formation of finely dispersed SCs particles by designing a unique melt-mixing procedure, where the mixing of PLLA with 0.75 wt% PDLA is first performed at elevated temperatures (far above the melting temperature of SCs) to allow the homogeneous mixing of PLLA/PDLA chains and then at a low temperature (slightly above that of homocrystallites) to permit the full stereocomplexation of the premixed chains. It is found that the SCs formed in the blends exhibit unexpectedly low NEs (e.g., 54.5%), much inferior to that (73.6%) in the counterpart without undergoing premixing. This is because the introduction of premixing leads to a remarkable deterioration in the amount of SCs particles formed, despite decreased particle size, highlighting that the direct mixing at low temperatures of 170–180 °C (about 20–30 °C lower than that used in common melt-processing of PLA) is more effective for the construction of SCs with superior NE. The mechanisms for these striking findings are discussed.     

非贵金属电解水催化剂改性研究进展

氢能作为理想的二次能源,具有能量密度高、清洁无污染等特点,在能源转型过程中将发挥极为重要的作用。电解水制氢被认为是获取氢能最有潜力的绿色工艺,而高效电催化剂是制约电解水制氢快速发展的关键。贵金属催化剂具有优良的电催化性能,但由于成本和储量问题严重限制其推广应用,因而开发低成本高活性的非贵金属催化剂逐渐成为研究热点。为提高非贵金属催化剂的电催化性能,需要对其进行一系列的改性优化工作。综述了近几年国内外非贵金属电解水催化剂的改性研究进展,详细介绍了几何构造（一维、二维、三维结构）和电子调控（组成优化、晶面调控、缺陷构造、杂原子掺杂等）两种非贵金属催化剂的改性方法,并对今后非贵金属电解水催化剂改性发展方向进行了展望。     

Effects of can parameters on canned—forging process of TiAl base alloy（Ⅱ）——Mechanical behavior

1　ＩＮＴＲＯＤＵＣＴＩＯＮＴｉＡｌａｌｌｏｙｈａｓｌｏｎｇｂｅｅｎｃｏｎｓｉｄｅｒｅｄａｓａｐｒｏｍｉｓ ｉｎｇｍａｔｅｒｉａｌｆｏｒｈｉｇｈｔｅｍｐｅｒａｔｕｒｅａｐｐｌｉｃａｔｉｏｎ ,ｄｕｅｔｏｉｔｓｅｘｃｅｌｌｅｎｔｈｉｇｈｔｅｍｐｅｒａｔｕｒｅ ｐ