高速网络Fast TCP拥塞控制算法的改进

随着网络技术的飞速发展和接入性能的不断提高,如今全世界的互联主干网络呈现出一种高速网络的特性。在这种网络特性下,传统网络中的TCP拥塞控制协议已经开始显现出不适应性,发现了FAST TCP协议中＂持续拥塞＂的形成机制,建立了数学模型来准确的描述＂持续拥塞＂所导致数据流之间带宽分配不公平的问题,进一步利用优先服务队列的方法解决了FAST TCP在网络中的持续拥塞现象。     

Sentinel-1-based flood mapping: a fully automated processing chain

This article presents an automated Sentinel-1-based processing chain designed for flood detection and monitoring in near-real-time (NRT). Since no user intervention is required at any stage of the flood mapping procedure, the processing chain allows deriving time-critical disaster information in less than 45 min after a new data set is available on the Sentinel Data Hub of the European Space Agency (ESA). Due to the systematic acquisition strategy and high repetition rate of Sentinel-1, the processing chain can be set up as a web-based service that regularly informs users about the current flood conditions in a given area of interest. The thematic accuracy of the thematic processor has been assessed for two test sites of a flood situation at the border between Greece and Turkey with encouraging overall accuracies between 94.0% and 96.1% and Cohen’s kappa coefficients (κ) ranging from 0.879 to 0.910. The accuracy assessment, which was performed separately for the standard polarizations (VV/VH) of the interferometric wide swath (IW) mode of Sentinel-1, further indicates that under calm wind conditions, slightly higher thematic accuracies can be achieved by using VV instead of VH polarization data.     

Surface tension calculation of the Ni3S2---FeS---Cu2S mattes

The surface tension of the Ni₃S₂-FeS-Cu₂S ternary mattes have been calculated from those of the Ni₃S₂-FeS·FeS-Cu₂S and Cu₂S-Ni₃S₂ pseudo-binary boundary systems by using geometric models (Kohler and Toop model) and a general solution model (Chou model). Taking account of the experimental accuracy of ±2.5%, the respective calculated results are in agreement with the experimental data. At the same time, surface tensions of molten Ni₃S₂-FeS-Cu₂S mattes and their pseudo-binary boundary systems are predicted based on Butler's original treatment with great attention to the model parameter β. The predicted results also agree with the experimental data. Therefore, the resulting iso-surface tension curves in molten Ni₃S₂-FeS-Cu₂S mattes at 1473K, especially calculated by using Kohler, Toop and Chou models, are generally acceptable.     

Simulation and fabrication of piezoresistive membrane type MEMS strain sensors

Two piezoresistive (n-polysilicon) strain sensors on a thin Si₃N₄/SiO₂ membrane with improved sensitivity were successfully fabricated by using MEMS technology. The primary difference between the two designs was the number of strips of the polysilicon patterns. For each design, a doped n-polysilicon sensing element was patterned over a thin 3 μm Si₃N₄/SiO₂ membrane. A 1000×1000 μm² window in the silicon wafer was etched to free the thin membrane from the silicon wafer. The intent of this design was to fabricate a flexible MEMS strain sensor similar in function to a commercial metal foil strain gage. A finite element model of this geometry indicates that strains in the membrane will be higher than strains in the surrounding silicon. The values of nominal resistance of the single strip sensor and the multi-strip sensor were 4.6 and 8.6 kΩ, respectively. To evaluate thermal stability and sensing characteristics, the temperature coefficient of resistance [TCR=(ΔR/R₀)/ΔT] and the gage factor [GF=(ΔR/R₀)/] for each design were evaluated. The sensors were heated on a hot plate to measure the TCR. The sensors were embedded in a vinyl ester epoxy plate to determine the sensor sensitivity. The TCR was 7.5×10⁻⁴ and 9.5×10⁻⁴/°C for the single strip and the multi-strip pattern sensors. The gage factor was as high as 15 (bending) and 13 (tension) for the single strip sensor, and 4 (bending) and 21 (tension) for the multi-strip sensor. The sensitivity of these MEMS sensors is much higher than the sensitivity of commercial metal foil strain gages and strain gage alloys.     

氰戊菊酯剂型加工研究进展

综述了近年来氰戊菊酯剂型加工研究进展，重点介绍了其混合制剂的发展情况。     

Odour emission ability (OEA) and its application in assessing odour removal efficiency

Odourous emissions from sewer networks and wastewater treatment plants (WWTPs) can significantly impact a local population. Sampling techniques such as wind tunnels and flux hood chambers are traditionally used to collect area source samples for subsequent quantification of odour emission rates using dilution olfactometry, however these methods are unsuitable for assessing liquid samples from point sources due to the large liquid volumes required. To overcome this limitation, a gas phase sample preparation method was developed for assessing the total Odour Emission Ability (OEA) from a liquid sample. The method was validated using two volatile organic sulphur compounds (VOSCs), dimethyl-trisulphide (DMTS) and bismethylthiomethane (BMTM) that are frequently detected from sewers and WWTPs and are relatively stable compared with common VOSCs like mercaptan or methyl mercaptan. The recovery rates of DMTS and BMTM were quantified by injecting a known volume of a standard liquid sample into Tedlar bags using a static injection and a dynamic injection methodology. It was confirmed that both dynamic and static injection methods at ambient condition achieved high recovery rates with no need to consider increasing evaporation by elevating the temperature. This method can also be used to assess odour removal effectiveness of liquids by comparing the OEA before and after the treatment tests. Two application examples were presented.     

Preface

Recently, there has been a dramatic increase in research on data mining on social networks and social media. Theubiquitous nature of Web-enabled devices, including desktops,     

石墨化炉的供电特点及发展趋势

通过对石墨化炉的特点及其供电方面的有关问题的分析，论述了石墨化炉供电的特点及其发展的趋势，并对石墨化炉在交、直流电源供电方面提出了看法，以不断提高石墨化炉供电的设计水平．