Adsorption characteristics of hexadecyl ammonium with different numbers of carbon chains in montmorillonite and the structure of the prepared composites

Journal of Porous Materials - The dynamics and thermodynamics of adsorption of hexadecyl ammonium with different numbers of carbon chains in montmorillonite (Mt) with different layer charge density...     

稀土含量对喷熔层组织及耐蚀性的影响

本文通过在镍基自熔合金粉末中加入不同含量的稀土，研究了稀土含量对喷熔层组织及耐蚀性的影响规律及其作用机制。结果表明，在喷熔材料中加入适量稀土，可使喷熔层组织细化、晶界净化，从而使腐蚀过程中的表面活性点减少，耐蚀性提高。     

持续发展是唯一出路

讨论了人类、环境与发展的关系，指出不适当的发展模式已使三者之间形成恶性循环，必须及时地改变发展模式。列举了中国面临的严重环境问题，指出只有走可持续发展的道路才是唯一出路。并提出为实施可持续发展应注意的６个主要问题。     

半刚性钢-混凝土组合节点受弯承载力的计算

在半刚性钢 -混凝土组合框架中 ,混凝土板中的纵向钢筋增加了节点的强度和刚度 ,但是 ,传统的设计方法往往忽略纵向钢筋的作用而采用简化的计算模型。因此 ,出于经济效益考虑 ,应该根据半刚性组合节点的实际受力性能建立更加准确的计算方法。这里详细介绍了考虑混凝土板纵向钢筋作用的半刚性组合节点受弯承载力的计算方法 ,计算结果表明 ,建议的公式与试验结果吻合良好 ,可供规范制定和工程应用参考。     

充气压力对充气工况载重斜交轮胎影响的有限元分析

进行了充气压力对充气工况载重斜交轮胎影响的有限元分析.结果表明,充气工况下,充气压力对斜交轮胎外形轮廓尺寸影响明显,其外直径、断面宽度均随充气压力的增大而增加;充气压力的大小对胎圈接触应力分布影响很小,但胎圈最大接触应力随充气压力的增加而增大.     

安全本质的再认识与当代安全问题

从现代科学的角度揭示和分析安全的本质含义。安全本质应该包括：一是预知、预测、分析危险；二是限制、控制、消除危险。当人们讲到危险的时候，实际上是在研究危险。安全的含义随着人类社会经济的发展而变化。当代事故的灾害性、社会性、突发性是由于事故过程的技术密集性和物质高能性引起的。本文从现代科学技术和社会经济发展的基本经济规律出发，分析当代事故的本质特性。     

New polyimide–silica organic–inorganic hybrids

A series of polyimide–silica hybrid films with silica contents up to 30 wt % were successfully prepared by the sol‐gel reaction of tetraethoxysiliane in the presence of poly(amic acid) containing pendent hydroxyl groups. The films were yellow and transparent when the silica content was less than 11 wt %. The chemical structure of the films was characterized by Fourier transform infrared spectroscopy, and the morphology of the films was investigated by scanning electronic microscopy and atomic force microscopy. Thermogravimetric analysis, differential scanning calorimetry, and stress–strain tests were used to measure the performance of the films. The results indicate that the glass‐transition temperatures and decomposition temperatures of the hybrid films increased with increasing silica content, whereas the tensile strength had a maximum with the variety of silica contents. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 2210–2214, 2003     

加压下二氧化碳在二甲基甲酰胺中的溶解度研究

本文报道了二氧化碳在二甲基甲酰胺中的溶解度,实验温度分别为15、20、25、30、35、40、45℃,实验压力为207.21—1684.02kPa.并且提出一个考虑了过量熵的、用溶度参数表示的活度系数方程.     

Seeded Crystallization of Leucite

The leucite crystallization kinetics from a hydrothermally derived precursor seeded with nano-crystalline leucite was investigated by X-ray diffraction and non-isothermal differential thermal analysis. The nano-crystalline leucite was prepared by high-energy milling of high-purity leucite powder and the leucite precursor was prepared by the hydrothermal method of silica sol, aluminum nitrate, and potassium nitrate. After the seeds were introduced, the crystallization temperature of the precursor was lowered by 100°C and the transition phase kalsilite did not appear during the crystallization process. When the seeded precursor was heat treated at 700°C, a small amount of cubic leucite was stabilized to room temperature. The seeded precursor showed an exothermic peak between 800° and 920°C under different heating rates. The activation energy for the growth of leucite from the seeded precursor was 256(SD9) kJ/mol.     

Decolorisation and mineralisation of CI Reactive Black 8 by the Fenton and ultrasound/Fenton methods

The effects of pH, ferrous ion and hydrogen peroxide dosage on the decolorisation and mineralisation of CI Reactive Black 8 by the Fenton process with/without ultrasonic irradiation were investigated. It was verified that the presence of ultrasonic irradiation did not enhance the decolorisation of CI Reactive Black 8 significantly by Fenton's reagents, but it enhanced the chemical oxygen demand removal efficiency. The enhancement was more pronounced for lower (<0.89 mm) or higher (>1.78 mm) ferrous ion dosage. The optimal pH for chemical oxygen demand removal was 3.0. Chemical oxygen demand removal efficiency increased with the increasing H₂O₂ dosage and reached the highest level at 5.88 mm, but further increase in H₂O₂ dosage would not increase removal efficiency significantly.