焊接设备中计算机控制系统的抗干扰

本文分析提出焊接设备中影响计算机控制系统的几种主要干扰。结合实际工作,提出了解决的措施和方法。     

An Analytical Model Including Interface Traps and Temperature Effects in Negative Capacitance Double Gate Field Effect Transistor

Silicon - In this paper, an analytical model for negative capacitance double gate field effect transistor (NC-DG-FET) is proposed. This model includes interface traps and temperature effects, which...     

Mold-filling characteristics of AZ91 magnesium alloy in the low-pressure expendable pattern casting process

The magnesium (Mg) alloy low-pressure expendable pattern casting (EPC) process is a newly developed casting technique combining the advantages of both EPC and low-pressure casting. In this article, metal filling and the effect of the flow quantity of inert gas on the filling rate in the low-pressure EPC process are investigated. The results showed that the molten Mg alloy filled the mold cavity with a convex front laminar flow and the metal-filling rate increased significantly with increasing flow quantity when flow quantity was below a critical value. However, once the flow quantity exceeded a critical value, the filling rate increased slightly. The influence of the flow quantity of inert gas on melt-filling rate reveals that the mold fill is controlled by flow quantity for a lower filling rate, and, subsequently, controlled by the evaporation of polystyrene and the evaporation products for higher metal velocity. Meanwhile, the experimental results showed that the melt-filling rate significantly affected the flow profile, and the filling procedure for the Mg alloy in the low-pressure EPC process. A slower melt-filling rate could lead to misrun defects, whereas a higher filling rate results in folds, blisters, and porosity. The optimized filling rate with Mg alloy casting is 140 to 170 mm/s in low-pressure EPC.     

Electron Emission from Barium Strontium Titanate Ceramics

This paper focuses on understanding the influence of materials' properties on the ferroelectric electron emission. Ferroelectric ( x =1.0 and 0.8) and paraelectric ( x =0.67 and 0.5) compositions of barium strontium titanate (Ba _x Sr_{(1− x )}TiO₃) system were chosen for study based on their different ferroelectric and dielectric properties. Similar emission current waveforms were obtained from four compositions with negative triggering voltage applied to the rear electrode of the samples. It was difficult to explain the experimental results using the spontaneous polarization-switching model. The mechanism of electron emission from Ba _x Sr_{(1− x )}TiO₃ ceramics was ascertained to surface plasma emission.     

扩链剂在PVC树脂生产中的应用

讨论了常见扩链剂的功能及在聚氯乙烯树脂生产中的应用。     

Synthesis,characterization, and thermal properties of phosphorus‐containing,wholly aromatic thermotropic copolyesters

A series of phosphorus‐containing, wholly aromatic thermotropic copolyesters from acetylated 2‐(6‐oxide‐6H‐dibenz〈c,e〉〈1,2〉oxa phosphorin‐6‐yl)‐1,4‐dihydroxy phenylene, p‐acetoxybenzoic acid, terephthalic acid, and isophthalic acid were prepared by melting polycondensation. The structure and basic properties of the polymers, such as the glass‐transition temperature (T_g), melting temperature (T_m), thermal stability, crystallinity, and liquid crystallinity, were investigated with Fourier transform infrared, elemental analysis, differential scanning calorimetry (DSC), thermogravimetric analysis, wide‐angle X‐ray diffraction, and hot‐stage polarizing optical microscopy. The copolyesters had relatively high T_g values ranging from 183 to 192°C. The T_m values obtained from DSC curves for samples P‐20 and P‐25 were 290 and 287°C, respectively (where the number in the sample name indicates the molar fraction of the phosphorus‐containing monomer in the reactants). The initial flow temperatures of other samples observed with hot‐stage polarizing microscopy were 271–290°C. The 5% degradation temperatures in nitrogen ranged from 431 to 462°C, and the char yields at 640°C were 41–52%. All the copolyesters, except P‐40, were thermotropic and nematic. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 1278–1284, 2002     

Improvement of Microwave Loss Tangent and Tunability of Ba0.55Sr0.45TiO3/MgO Composites Using the Heterogeneous Precipitation Method

Ba_0.55Sr_0.45TiO₃/MgO composites were successfully prepared by the heterogeneous precipitation method and their structural, surface morphological, tunable properties, and dielectric properties at microwave frequency were systemically investigated. Compared with the sample prepared by the traditional solid-state method, the sample prepared by the heterogeneous precipitation method exhibits a smaller grain size, more uniform microstructure, higher tunability, and lower microwave loss, and these properties are very beneficial to the development of the microwave tunable devices application. Moreover, the effects of La₂O₃ doping on the dielectric and tunable properties of BST/MgO composites are investigated. The result shows that the La³⁺-doped sample has higher tunability and lower microwave loss than the undoped one.     

Synthesis and self-assembly of hyperbranched polyester peripherally modified by touluene-4-sulfonyl groups

In this paper, hyperbranched polyesters (HPs) were synthesized in the molten state from 2,2-bis(hydroxymethyl) propionic acid (bis-MPA) and 2-ethyl-2-hydroxymethyl-1,3-propanediol (TMP) using acid catalysis. The modified hyperbranched polyesters were obtained through the chemical modification of the hyperbranched polyester cores by substituting a controlled fraction of the terminal hydroxyl groups with touluene-4-sulfonyl chloride using triethylamine (TEA) as an acceptor of HCl. The resultant polyesters were characterized by ¹H NMR, ¹³C NMR, FT-IR, UV and GPC and their self-assembly behaviors were investigated. The results revealed that self-assembled structures could be formed in selected solvents (trichloromethane/acetone or trichloromethane/n-hexane).     

金属间化合物的研究现状及其最新发展趋势

主要介绍了金属间化合物的概念、发展历程、研究现状及几种常用金属间化合物的发展状况，并提出了该类材料的最新发展趋势。