Effect of surface-modifying macromolecules and solvent evaporation time on the performance of polyethersulfone membranes for the separation of chloroform/water mixtures by pervaporation

Polyethersulfone (PES) membranes using different evaporation periods were fabricated by the phase-inversion method. Pervaporation experiments were conducted for chloroform/water mixtures to determine the selectivity of the PES membranes. It was found that chloroform could be concentrated in the permeate from chloroform/water binary feed mixtures by PES membranes prepared using longer evaporation periods, and that the selectivity of PES membranes in pervaporation could be reversed by shorter evaporation periods. This study also showed that by adding surface-modifying macromolecules (SMM) up to 1 wt % into the casting solution, chloroform enrichment in the permeate could be increased by 50%. Chloroform enrichment increased with increasing SMM concentration until an optimal value, after which the enrichment decreased. © 1994 John Wiley & Sons, Inc.     

Network model approach for calculating oscillating frequency of thermoacoustic prime mover

The network model is given and used to calculate the oscillating frequency of thermoacoustic prime mover. Theoretically calculated frequency by the model is plural, whose real part denotes actual frequency of the system, and imaginary part means attenuation coefficient of acoustic pressure. Numerical calculation is made under different conditions including different acoustic cavities, spacing between each parallel plate, gas pressures and system lengths. Theoretically calculated frequency and experimentally measured frequency are in quite good agreement.     

发电机同轴励磁机电刷火花过大的原因及处理方法

本文对发电机同轴励磁机电刷火花过大的原因进行了分析．并针对这些原因提出了相应的处理办法。对规范励磁机的运行维护有很大的帮助。     

N,N′-二(β-十八酰氧基)乙基乙二胺二乙酸钠的合成及性能研究

用 N,N′-二羟乙基乙二胺、氯乙酸钠合成了 N,N′-二羟乙基乙二胺二乙酸钠(中间体),中间体再与硬脂酰氯反应制备了一种新型 Gemini 两性表面活性剂 N,N′-二(β-十八酰氧基)乙基乙二胺二乙酸钠。对产物合成条件进行了考察,优化的反应条件为:n(硬脂酰氯):n(中间体)=2.5,溶剂 V(水):V(氯仿)=1:2,pH=9.0～10.0,反应温度15～20℃,反应时间5 h。通过红外光谱和质谱分析确定了产物结构,并测试了产物的表面性能。结果表明,在25℃时,该产物的临界胶束浓度为0.24 mmol/L,临界胶束浓度下的表面张力为35.7 mN/m;即时泡沫高度为250 mm,5 min 后泡沫高度为220 mm;乳化时间为22.48 min(甲苯-水物系)和4.65 min(正己烷-水物系),亲水-亲油平衡值为5.4,等电点为 pH 3.3～6.5。     

Signature analysis and defect detection in layered manufacturing of ceramic sensors and actuators

This paper presents the concept of a process signature for the use of online signature analysis and defect detection in the layered manufacturing (LM) of ceramic sensors and actuators. To achieve the high quality of parts built by the fused deposition of ceramics (FDC), an online process-monitoring system is implemented to detect the processing defects. Using a process signature extracted from the image of a layer captured by the monitoring system, an ideal image is created that is then compared to the original image to detect and identify the defects. Some results of signature analysis and defect detection for single-material and multi-material parts are also presented.Received: 22 July 1999, Accepted: 21 October 2001, Published online: 29 October 2003 Correspondence to: Mohsen A. JafariThis work was supported by the Office of Naval Research under grant # N-0014-96-1-1175. Ref. US Patent # S-5738817, April 14, 1998.     

Application of ultrasonic waves in activation of microcrystalline cellulose

In this work, microcrystalline cellulose (MCC) was activated with ultrasonic waves. The influences of ultrasonic treatment on the changes of supramolecular structures and morphology structure were studied by WAXS and SEM. The accessibility of the MCC was characterized by water retention value (WRV) and specific surficial area. The influence of ultrasonic treatment on the reactivity of MCC was investigated through the reaction of MCC being oxidized into 2,3‐diadehyde cellulose (DAC) by periodate sodium. The mechanism of the reactivity change of ultrasonically treated MCC was examined. The results showed that the degree of crystallinity of MCC decreased and the degree of polymerization showed little change after treatment with ultrasonic waves. The morphologial variation of the treated MCC was significant when compared with the untreated MCC, which contribute to the improvement of accessibility. The aldehyde content of DAC prepared from ultrasonically treated MCC was improved from 64.19 to 85.00%, indicating that the regioselective oxidation reactivity of MCC was significantly improved. The aldehyde content was found to first increase with time of ultrasonic treatment to a point, and then decrease as time progressed. In addition, the aldehyde content was found to increase with an increase in ultrasonic power. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of the graft yield of maleic anhydride on the rheological behaviors,mechanical properties,thermal properties,and free volumes of maleic anhydride grafted high‐density polyethylene

The rheological behavior, thermal properties, and molecular mobility of a series of maleic anhydride (MA) grafted high‐density polyethylenes were characterized and evaluated. The rheological behavior was studied with a Haake minilaboratory. The viscosity of the samples in their melt state decreased with an increase in the graft yield, and this could be attributed to the higher molecular mobility for samples with a higher degree of grafting. The thermal properties were investigated with dynamic mechanical analysis and differential scanning calorimetry. Positron annihilation lifetime measurements were used to study the effect of the degree of grafting on the chemical environment and the atomic‐scale free‐volume properties. It was found that the grafted MA group played a significant chemical inhibition role in positronium formation when the graft yield was low. The results also indicated that the higher the degree of grafting was, the broader the free‐volume distribution was. The relationship between the microstructure and rheological behavior is discussed. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and structural characterization of methacrylic acid/octadecyl acrylate‐graft‐poly(methylhydrosiloxane) by hydrosilylation

Methylmethacrylate (MMA) and octadecyl acrylate (OA) were grafted to poly(methylhydrosiloxane) (PMHS) by hydrosilylation, respectively, with hexachloroplatinic acid as catalyst, and the former was further hydrolyzed to prepare methacrylic acid (MAA)‐graft‐PMHS under the alkaline condition. Through orthogonal experiment, main factors affecting the graft reaction between OA and PMHS were discussed and arranged in a decreasing order according to their abilities of the effect on the hydrosilylation of OA with PMHS: catalyst dosage, reaction temperature, reaction time, material ratio, and solvent dosage. It was found that the hydrosilylation of OA with PMHS was easier to that of MMA with PMHS. Under optimal conditions, the grafting ratios of MMA with PMHS and OA with PMHS reached about 90 and 95%, respectively. FTIR and ¹H NMR spectra indicated that the hydrosilylation reactions followed the Markovnikov's rule and played a strong preference toward β‐1,2‐addition. The test of contact angle indicated that surface energy of a system was mainly dependent on the polar groups. The surface energy of OA‐graft‐PMHS (35.07 mN/m) was similar to those of PMHS (35.62 mN/m) and polyoctadecyl acrylate (36.57 mN/m), and lower than that of MAA‐graft‐PMHS (43.50 mN/m). © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Accelerated wear testing with a microfabricated surface to evaluate the lubrication ability of biomolecules on polyethylene

Wear of ultrahigh‐molecular‐weight polyethylene (UHMWPE) and wear‐particle‐induced osteolysis and bone resorption are the major factors causing the failure of total joint replacements. It is feasible to improve the lubrication and reduce the wear of artificial joints. We need further understanding of the lubrication mechanism of the synovial fluid. The objective of this study is to evaluate the lubricating ability of three major components in the synovial fluid: albumin, globulin, and phospholipids. An accelerated wear testing procedure in which UHMWPE is rubbed against a microfabricated surface with controlled asperities has been developed to evaluate the lubrication behavior. An analysis of the wear particle dimensions and wear amount of the tests has provided insights for comparing their lubrication performance. It is concluded that the presence of biomolecules at the articulating interface may reduce friction. A higher concentration of a biological lubricant leads to a decrease in the wear particle width. In addition, in combination with the wear results and mechanical analysis, the roles of individual biomolecules contributing to friction and wear at the articulating interface are discussed. These results can help us to identify the role of the biomolecules in the boundary lubrication of artificial joints, and further development of lubricating additives for artificial joints may be feasible. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008