Preparation and photoluminescence properties of γ-KCaPO4: Eu phosphors for near UV-based white LEDs

Novel whitish-blue phosphors based on a phosphate host matrix, γ-KCaPO₄: Eu²⁺, were prepared by a conventional solid-state reaction method using slightly phosphorus deficient conditions and their photoluminescence properties were investigated. The concentration quenching process, temperature dependence of the luminescence and decay curve were also investigated. The γ-KCaPO₄: Eu²⁺ phosphor was efficiently excited by UV-Visible light at wavelengths of 200-450 nm and exhibited a bright whitish-blue emission with a maximum peak wavelength of 473 nm. All of these characteristics suggest that the γ-KCaPO₄: Eu²⁺ phosphors combined with red phosphors could be applicable to near UV-based white LEDs, i.e., only two kinds of phosphor powders are needed for the formation of white light.     

A theoretical and experimental investigation of the tool-tip vibration and its influence upon surface generation in single-point diamond turning

This paper presents a theoretical and experimental investigation of the influence of tool-tip vibration on surface generation in single point diamond turning (SPDT). Although it is well known that the relative vibration between the tool and the workpiece plays an important role in the surface generation in single-point diamond turning, most of the prior work has been focused on studying the relative tool-work vibration in the infeed (thrust force) direction while the significant contribution of the effect of the tool-tip vibration in the cutting force direction has been overlooked. In the present study, two characteristic peaks (twin peaks) are identified and found to be corresponding to the tool-tip vibrations by power spectrum density (PSD) analyses. The vibrations possess the features of small amplitude but high frequency. A physical model is proposed to capture the dominant factor based on the characteristic and it reveals that the twin peaks are attributed by the impact between the tool tip and workpiece and the process damping effect. Hence, a geometric model of surface roughness is proposed to take account of tool-tip vibration and it is verified through a series of experiments. The simulation results have been found to agree well with the experimental results.     

气相色谱-质谱法分析酚焦油的主要组分

实验采用气相色谱-质谱法(GC-MS)对酚焦油的主要组分进行了定性和定量测定,结果表明:使用SE-54毛细管柱、控制升温条件,能够同时检测出酚焦油中各主要组分含量,测定方法简便、快速、灵敏、准确。     

Management of the variability of vibration response levels in mistuned bladed discs using robust design concepts. Part 2: Tolerance design

The mistuning pattern on a bladed disc is controlled in Part 2 of the two-part article either by (i) imposing a small maximum allowable mistune according to the small mistuning approach or (ii) incorporating non-identical blades of specific patterns, known as the intentional mistuning approach. These approaches resemble the tolerance design stage of the Taguchi method of robust design. The first-order maximum amplification factor sensitivity in a single-degree-of-freedom (DOF)-per-sector system is derived to support a new definition of the interblade coupling ratio and to illustrate the dependence of the maximum amplification factor sensitivity on design parameters of a bladed disc. It is found that the variability of the forced vibration response levels in flexible bladed discs can be reduced by controlling the degree of mistune within realistic levels. The potential of a “linear” mistuning pattern to become an effective intentional mistuning pattern is evaluated by observing the amplification factors of bladed discs with combined intentional mistuning and additional random mistuning. A tool based on the importance sampling method is used to reduce the computational effort in determining the magnitude of intentional mistuning. Guidelines of designing bladed discs with a lower variability of forced vibration response levels are given according to the findings in casting the blade mistuning problem as a robust design problem.     

刍议历史地段插建建筑形态设计

该文依据历史地段插建建筑与其所处环境之间的三种位置关系,结合具体案例对其形态设计策略进行详细探讨。     

Amplifier linearization using compact microstrip resonant cell-theory and experiment

This paper presents a novel technique for reducing the intermodulation distortions (IMDs) in power amplifiers. In this method, both second- and third-harmonic components generated by the transistor are reflected back simultaneously by the compact microstrip resonant cell (CMRC) at the input port with proper phases to mix with the fundamental signal for the reduction of IMDs. A rigorous mathematical analysis on the effectiveness of multiharmonic reflections has been formulated and derived using the Volterra series. Moreover, the delay mismatch factor of the proposed method is analytically studied and the result shows that a better tolerance to the delay error can be achieved by using CMRC circuitry. Standard two-tone test measurements reveal 32- and 22-dB reductions for the third-order IMD and fifth-order IMD, respectively, without affecting the fundamental signal at 2.45 GHz. Meanwhile, the proposed approach gives a peak power added efficiency of 53% with 11.5 dB transducer gain and 15 dBm output power for a single-stage SiGe bipolar junction transistor. The adjacent channel power ratio (ACPR) is -55dBc for a data rate of 384-kb/s quadrature phase shift keyed modulated signal with 2-MHz spanning bandwidth, and this ACPR is maintained for a broad range of output power level.     

FVF LDO regulator with dual dynamic-load composite gain stage

A low-voltage output-capacitorless low-dropout regulator using dual dynamic-load composite gain stage for flipped voltage follower topology is presented. It also incorporates a delay discharge circuit which aims to reduce the long discharge time arising from the large capacitive load, thus achieving the overshoot time reduction and sustaining fast transient characteristic when driving low-power digital system with internal heavy capacitive load requirement. The regulator can support a minimum of 0.75 V input voltage with 0.5 V output voltage. It consumes 49.4 µA whilst maintaining the stability for a capacitance load range from 470 pF to 10 nF. For a current load transient from 0 to 10 mA with 200 ps edge time, the settling time is 0.38 µs for the load capacitance of 3 nF. The obtained transient figure-of-merit is 0.42 mV. This transient metric outperforms the representative prior-art reported works.     

Highly Crystalline Soluble Acene Crystal Arrays for Organic Transistors: Mechanism of Crystal Growth During Dip‐Coating

The preparation of uniform large‐area highly crystalline organic semiconductor thin films that show outstanding carrier mobilities remains a challenge in the field of organic electronics, including organic field‐effect transistors. Quantitative control over the drying speed during dip‐coating permits optimization of the organic semiconductor film formation, although the kinetics of crystallization at the air–solution–substrate contact line are still not well understood. Here, we report the facile one‐step growth of self‐aligning, highly crystalline soluble acene crystal arrays that exhibit excellent field‐effect mobilities (up to 1.5 cm V^?1 s^?1) via an optimized dip‐coating process. We discover that optimized acene crystals grew at a particular substrate lifting‐rate in the presence of low boiling point solvents, such as dichloromethane (b.p. of 40.0 °C) or chloroform (b.p. of 60.4 °C). Variable‐temperature dip‐coating experiments using various solvents and lift rates are performed to elucidate the crystallization behavior. This bottom‐up study of soluble acene crystal growth during dip‐coating provides conditions under which one may obtain uniform organic semiconductor crystal arrays with high crystallinity and mobilities over large substrate areas, regardless of the substrate geometry (wafer substrates or cylinder‐shaped substrates).     

A Versatile Iterative Framework for the Reconstruction of Bandlimited Signals from Their Nonuniform Samples

In this paper, we study a versatile iterative framework for the reconstruction of uniform samples from nonuniform samples of bandlimited signals. Assuming the input signal is slightly oversampled, we first show that its uniform and nonuniform samples in the frequency band of interest can be expressed as a system of linear equations using fractional delay digital filters. Then we develop an iterative framework, which enables the development and convergence analysis of efficient iterative reconstruction algorithms. In particular, we study the Richardson iteration in detail to illustrate how the reconstruction problem can be solved iteratively, and show that the iterative method can be efficiently implemented using Farrow-based variable digital filters with few general-purpose multipliers. Under the proposed framework, we also present a completed and systematic convergence analysis to determine the convergence conditions. Simulation results show that the iterative method converges more rapidly and closer to the true solution (i.e. the uniform samples) than conventional iterative methods using truncation of sinc series.     

Understanding the Meniscus‐Guided Coating Parameters in Organic Field‐Effect‐Transistor Fabrications

Meniscus‐guided coating (MGC) is mainly applicable on the soluble organic semiconductors with strong π–π overlap for achieving single‐crystalline organic thin films and high‐performance organic field‐effect‐transistors (OFETs). In this work, four elementary factors including shearing speed (v), solute concentration (c), deposition temperature (T), and solvent boiling point (T_b) are unified to analyze crystal growth behavior in the meniscus‐guided coating. By carefully varying and studying these four key factors, it is confirmed that v is the thickness regulation factor, while c is proportional to crystal growth rate. The MGC crystal growth rate is also correlated to latent heat (L) of solvents and deposition temperature in an Arrhenius form. The latent heat of solvents is proportional to T_b. The OFET channels grown by the optimized MGC parameters show uniform crystal morphology (Roughness R_q < 0.25 nm) with decent carrier mobilities (average µ = 5.88 cm² V^?1 s^?1 and highest µ = 7.68 cm² V^?1 s^?1). The studies provide a generalized formula to estimate the effects of these fabrication parameters, which can serve as crystal growth guidelines for the MGC approach. It is also an important cornerstone towards scaling up the OFETs for the sophisticated organic circuits or mass production.