火炮身管内表面激光硬化处理的实验研究

提高身管寿命是火炮行业亟待解决的关键技术问题，激光表面改性技术是解决这一问题的有效方法之一。本文在分析激光表面相变硬化性能的基础上，对身管内表面进行了激光硬化处理实验研究，检测了其内表面阳线和阴线的硬化层硬度和深度，对比分析了离焦量和焦深对其内表面硬化层硬度的影响，并对激光相变硬化层金相组织进行了分析。经激光硬化处理后，身管的内表面硬度有明显提高，硬化层较深，且为很细的条状马氏体组织。     

无油分子泵机组的组装

介绍了将ALCATEL公司生产的一台ATPl00涡轮分子泵、一台MDP50ll牵引分子泵及一台VRC公司生产的lBy6型干泵组装成无油分子泵机组的过程。文中给出了泵间配合的计算、机组方案的设计、连接管路、仪器支架的设计及选择。本机组所采取的设计方案使三个泵都最大限度地发挥了优点避免了缺陷，较好地满足了使用要求，为今后选购单泵和组装无油分子泵机组提供了可靠的理论和实验依据。     

加强电站无功管理

加强电站无功管理，不但能改善供电质量，满足电网的要求，提高单位的经济效益，而且使设备的安全运行得到了保障。     

深井长裸眼跨隔测试新工艺的应用

为减少勘探费用，缩短施工周期，取全取准各项地质资料，采取中途测试工艺。随着深井中途测试不断增多，特别是跨隔支撑测试具有一定施工风险和难度，要求测试质量不断提高。结合油田生产实际，合理选配了地层测试工具仪表，不断改进测试管串和优化施工设计，经盐22井中途跨隔测试应用，获得成功。     

Mobility management architectures based on joint mobile IP and SIP protocols

In the all-IP wireless networks beyond the third generation, mobility management can be effectively achieved by applying mobile IP (MIP) and the session initiation protocol (SIP) jointly. Nevertheless, an efficient combination of both protocols remains an open research issue. Conventional hybrid MIP-SIP mobility architectures operate MIP and SIP almost independently, resulting in significant redundant costs. This article investigates the representative hybrid MIP-SIP architectures and explores the joint optimizations between MIP and SIP for a more cost-efficient mobility support whilst utilizing their complementary power. Two novel design approaches are presented. The first approach culminates in a tightly integrated architecture, which merges the redundant mobility entities in MIP and SIP to yield maximum system efficiency. The other approach leads to a loosely integrated architecture, where necessary interactions are introduced between MIP and SIP mobility servers while their physical entities are kept intact. Major mobility procedures, including location update, session setup and handoff, are discussed in these architectures. The analytical results demonstrate that both proposed architectures outperform typical hybrid MIP-SIP architectures in terms of clear-cut reduced signaling costs     

应用激光活化饵料藻种的研究

应用Nd:YAG激光(波长1.06μm,功率5w,照射时间0.5-3 min)和Ar+激光(波长488nm,功率70mw,照射时间5-15min)对长期保存的不同保存形式的塔胞藻(Pyramidomonassp.)进行辐照处理。研究了不同剂量激光辐照对藻体生长和叶绿素含量的影响。实验结果表明:照射剂量为60s的Nd:YAG激光及剂量为15min的Ar+激光对液体保存形式的藻种有较明显的促长效果,接种后这两种激光处理组的比生长速率分别较对照提高达53.33%和28.89%,叶绿素含量分别增加73.33%和65.69%。两种激光对液体保存藻种的活化效果均好于固体保存种。     

High resistivity measurement of SiC wafers using different techniques

To establish fast, nondestructive, and inexpensive methods for resistivity measurements of SiC wafers, different resistivity-measurement techniques were tested for characterization of semi-insulating SiC wafers, namely, the four-point probe method with removable graphite contacts, the van der Pauw method with annealed metal and diffused contacts, the current-voltage (I-V) technique, and the contactless resistivity-measurement method. Comparison of different techniques is presented. The resistivity values of the semi-insulating SiC wafer measured using different techniques agree fairly well. As a result, application of removable graphite contacts is proposed for fast and nondestructive resistivity measurement of SiC wafers using the four-point probe method. High-temperature van der Pauw and room-temperature Hall characterization for the tested semi-insulating SiC wafer was also obtained and reported in this work.     

不同注F剂量与CMOS运放电路辐照损伤的相关性

在不同注F剂量条件下,对P沟和N沟两种不同差分对输入CMOS运放电路的电离辐照响应进行了研究.分析比较了注F和未注F运放电路电离辐照响应之间的差异.结果表明,在栅场介质注入适量的F,可有效抑制辐照感生的氧化物电荷尤其是界面态的增长,从而提高CMOS运放电路的抗辐照特性.     

计算机网络安全系统设计

分析了现代计算机网络所面临的威胁和各种安全问题,同时提出了在设计一个有关网络系统时应该考虑的一些安全问题,如网络安全策略与技术、网络的访问控制、网络数据加密技术、信息隐藏技术等安全问题。     

An optimization model for placement of wavelength converters to minimize blocking probability in WDM networks

The introduction of wavelength converters in wavelength division multiplexing (WDM) networks can reduce the blocking probabilities of calls. In this paper, we study the problem of placing a given number of converters in a general topology WDM network such that the overall system blocking probability is minimized. The original contributions of this work are the following: 1) formulation of success probability in a network as a polynomial function of the locations of converters; 2) proposal of an optimization model of the converter placement problem as the minimization of a polynomial function of 0-1 variables under a linear constraint, so that standard optimization tools can be employed to solve the problem; and 3) design of a search algorithm that can efficiently find the optimal solution to the converter placement problem. Experiments have been conducted to demonstrate the effectiveness of the proposed model and the efficiency of the algorithm.