Structural,morphological, dielectric and magnetic properties of Zn-Zr co-doping yttrium iron garnet

In this study, yttrium iron garnet co-doped with Zn and Zr atoms with a chemical formula Y₃Zn_xZr_xFe_(5−2x)O₁₂ (x = 0.0-0.3) has been successfully prepared by the solid-state reaction method. The effects of doping concentration on the microstructure, crystal structure, magnetic properties, and dielectric properties of Y₃Zn_xZr_xFe_(5−2x)O₁₂ were investigated. The microstructure analysis indicates that co-doping of YIG with Zn and Zr can effectively reduce the grain size of the ceramic. The crystal structure results reveal that the doping concentration of Zn–Zr has substantial influence on the lattice parameters of YIG, such as, increases the lattice constant, crystal cell size, and interplanar spacing. However, the second phase of ZrO₂ appears once x ≥ 0.15. Additionally, the dielectric properties of YIG ferrite can be regulated using this Zn–Zr co-doping method. Zn–Zr co-doping can improve the dielectric stability and reduce the dielectric loss at high temperature. The magnetization measurement shows that the saturation magnetization is stabilized at x < 0.15, and the magnetic loss is decreased with the increase in the doping concentration. Overall, the findings show that the ceramic with x = 0.1 exhibits better properties included high saturation magnetization (24.607 emu/g), low magnetic loss (0.0025 @ 1 MHz), and relatively low dielectric loss (496 @ 400°C).     

Effects of ethylene-octene copolymer (POE) on the brittle to ductile transition of high-density polyethylene/POE blends

Three kinds of ethylene-octene copolymers (POE) were melt-blended with high-density polyethylene (PE-HD) in different proportions. Detailed characterizations were conducted to analyze their structural differences of POE and its effects in toughening PE-HD. The higher molecular weight POE can improve the toughness of PE-HD. 60:40 PE-HD/POE is elongated to break up to 700% while impact strength is 84.7 kJ/m² at −30°C, which is 21-fold of PE-HD. In the brittle to ductile transition (BDT) during impact, the fracture mechanism changes from the crazing mode to the shear yield-plastic deformation mode. The BDT temperature decreases as the POE molecular weight and its content increase. The interface strength in tension is estimated to access their effects. The Boltzmann-type models were successfully extended to describe the typical S-shaped curves in BDT of notched impact strength vs POE content or temperature. The supplementary decay model is suggested for the attenuation in toughening. Transition map in impact is proposed to select the use range of composition (c ) and temperature (T ) for high toughness. The curves are converted into 3D graph of T -c -impact strength for illustrating their coupling-separate effects, and further into the contour map of impact strength in T -c space for finding their partial equivalence.     

Corrosion behavior of Cu–Sn bronze alloys in simulated archeological soil media

The corrosion behavior of synthetic Cu–Sn bronze alloys with six different Sn contents was examined through an electrochemical test and a synthetic test in a simulated corrosive medium. The mechanism of corrosion and the morphology of the corroded surfaces were characterized through field emission scanning electron microscopy equipped with energy-dispersive spectroscopy. At the corrosion potential, the corrosion behavior appears to be determined by the charge transfer step and the diffusion process. It was found that the bronze-IV (Cu–26.8Sn) specimen exhibited the best corrosion resistance, as evidenced by a low corrosion current density and a high impedance. This improvement resulted from an increase in the content of the Cu–Sn solid solution in the alloy, which was conducive to forming a relatively more protective passive film on the surface of the bronze alloy. This finding would be valuable in the anticorrosion protection of archeological artefacts after their excavation.     

Structure, properties, and thermal stability of nanocrystallite Fe-Ti-N soft magnetic films

We deposited Fe-Ti-N magnetic films with a high sputtering power of 7 W/cm/sup 2/. When the composition of the films was in the range of Fe-Ti(3.9 at.%)-N(8.8 at.%) to Fe-Ti(3.3 at.%)-N(13.5 at.%), the films were composed of /spl alpha/' and Ti/sub 2/N precipitates. With the addition of nitrogen, 4/spl pi/M/sub s/ became higher than that of pure iron, reaching a maximum of 23.8 kG. At the same time, H/sub c/ was reduced to a minimum of 1.12 Oe. The best films can meet the needs of the recording head in dual-element giant magnetoresistive/inductive heads, yielding high storage density (10 Gb/in/sup 2/). The incorporation of N in /spl alpha/-Fe brought about the /spl alpha/' phase with its higher saturation magnetization. Ti additions inhibited the equilibrium decomposition /spl alpha/'/spl rarr//spl alpha/+/spl gamma/'. Because H/sub C//sup D//spl prop/D/sup 6/, where D is average grain diameter, grain size control is very important. The nitrogen induces severe distortion of the /spl alpha/' lattice, which can cause the grains to break into pieces and reduce the grain size. High sputtering power also led to the formation of fine grains, with diameter in the order of 14 nm. Probably Ti/sub 2/N is preferentially precipitated on the grain boundary, pinning the grain boundary and stabilizing the grain size during high-temperature heat treatment. The temperature limit for stability of the structure and its associated low coercivity was not less than 520/spl deg/C.     

Popular biorthogonal wavelet filters via a lifting scheme and its application in image compression

A technique using a lifting scheme is presented for constructing compactly supported wavelets whose coefficients are composed of free variables locating in an interval. An efficient approach-based wavelet for image compression is developed by selecting the coefficients of the 9-7 wavelet filter and associated lifting scheme. Furthermore, the rationalised coefficients wavelet filter that can be implemented with simple integer arithmetic is achieved and its characteristic is close to the well known original irrational coefficients 9-7 wavelet filters developed by A. Cohen et al. (Commun. Pure Appl. Maths., vol.45, no.1, p.485-560, 1992). To reduce the computational cost of image coding applications further, an acceleration technique is proposed for the lifting steps. Software and hardware simulations show that the new method has very low complexity, and simultaneously preserves the high quality of the compressed image.     

地震多次波压制方法技术应用研究

辽河盆地西部凹陷地质条件复杂，地震波场中多次波较发育，受其影响，主要目的层反射波干涉现象较严重，有效波难以识别，总体信噪比不高，给构造及岩性解释造成困难。对三维地震资料的处理研究表明，采用预测反褶积、F—K域多次波衰减技术及近道内切法等相结合的方法压制多次波是一种有效的途径。从资料处理效果看，剖面质量明显得到改善，证明该组合去噪技术是切实可行的。     

县区电网电压无功控制系统设计

针对目前地区电网电压无功控制的现状,提出了电网电压无功监控系统的设计方案。说明优化控制系统应该实现的功能,选用线性规划(LP)算法为核心程序,正常状态下以有功网损最小为目标函数。依据分离原理提出两层分级控制的系统结构,分析优化控制系统的工作流程及特点。     

"十一五"规划国家级重点通信项目

《信息产业科技发展“十一五”规划》提出设立部分重大项目,力争实现重点突破,形成一批具有自主知识产权的核心技术和创新产品,打造较为完整的产业链,形成世界一流的产业群。这其中,与通信相关的重点项目主要有:宽带无线移动通信、下一代网络、家庭网络、智能终端、数字电视等。本部分将对我国在以上领域的现状、项目的具体内容和目标、实现这些目标的具体计划以及相关厂商在各领域的努力和成绩进行介绍。     

砾岩储层精细描述中标准测井资料的应用

克拉玛依油田七区的标准测井资料是指使用标准电极系视电阻率测井、自然电位测井和井径测井,以相同的1:500深度比例尺及相同的横向比例进行测井作业所取得的资料.这种资料本来并不具备定量解释储层孔隙度和含油饱和度的能力,但这种资料占该区测井资料总量的比率高达34%.利用标准电极系视电阻率资料和岩心分析资料建立了视电阻率-岩性图版,利用自然电位减小系数α和岩心孔隙度分析资料φ建立了α-φ图版,根据综合测井资料求出标准测井视电阻率校正系数,进而确定了饱和度计算方程的参数.与相应的综合测井资料计算结果相对比,用该方法得到的孔隙度平均绝对误差及相对误差分别为1.85%和11.88%;含油饱和度平均绝对误差及相对误差分别为9.08%和24.75%.将该方法有选择地应用到该区砾岩储层精细描述研究中,弥补了缺乏综合测井资料无法进行测井储层评价及参数研究的缺陷.     

Mining predecessor–successor rules from DAG data

Data mining extracts implicit, previously unknown, and potentially useful information from databases. Many approaches have been proposed to extract information, and one of the most important ones is finding association rules. Although a large amount of research has been devoted to this subject, none of it finds association rules from directed acyclic graph (DAG) data. Without such a mining method, the hidden knowledge, if any, cannot be discovered from the databases storing DAG data such as family genealogy profiles, product structures, XML documents, task precedence relations, and course structures. In this article, we define a new kind of association rule in DAG databases called the predecessor–successor rule, where a node x is a predecessor of another node y if we can find a path in DAG where x appears before y. The predecessor–successor rules enable us to observe how the characteristics of the predecessors influence the successors. An approach containing four stages is proposed to discover the predecessor–successor rules. © 2006 Wiley Periodicals, Inc. Int J Int Syst 21: 621–637, 2006.