TiO2/MOFs的制备及污染物降解现状

TiO2是较为成熟的半导体光催化材料,但因TiO2分散性差、量子利用率低、比表面积小、难回收等问题难以工业化.多孔金属有机框架(MOFs)的引入可增强TiO2/MOFs复合材料的光吸收性能,提高电子-空穴对分离效率和提高回收率.基于TiO2/MOFs制备时前驱体添加顺序不同,综述了TiO2/MOFs的3种制备方法(即Ship-in-a-bottle法、Bottle-around-ship法、One-pot法)及TiO2/MOFs光催化机理与性能影响因素,并探讨不同MOFs与TiO2结合的作用机理.最后,对TiO2/MOFs存在的问题提出建议.     

大型薄壁铝铸件表面沟槽缺陷的产生及消除

针对大型薄壁铝铸件内腔表面出现的沟槽缺陷,从差压铸造、树脂砂、铸件结构等工艺条件方面探讨了产生的机理,并通过试验和对比研究,确定排气不畅是该缺陷的首要引发因素,找到了消除该缺陷的工艺方法,提出了相关预防措施,避免了因此产生的废品损失.     

Synthesis and characterization of maltose fatty acid monoesters as biosurfactants

Maltose long-chain fatty acid esters (MFAE), esterified at the 6 and 6′ position, were synthesized with stearic, palmitic, myristic, and oleic groups. Synthesis yields were 15–20% based on initial maltose present, and structural confirmation was obtained using plasma desorption mass spectrometry and nuclear magnetic resonance spectroscopy. These surfactants have surface tensions in the range of 34–36 dyn/cm at their critical micelle concentrations (CMC) of approximately 10⁻⁵–10⁻⁶ mol/L. The increased chain lengths have a marked effect, reducing CMC values for MFAE by approximately three orders of magnitude over similar carbohydrate-based dodecyl chain sources. Within chain lengths between 14 and 18 carbons, the rate of change in CMC is significant and decreases with increasing chain length for MFAE. The melting points of MFAE are approximately 40°C, and the heat capacities range from 1.6 to 1.9 J/g·K. These numbers are comparable to those of sucrose esters, indicating their applicability in similar uses. However, because MFAE, unlike sucrose, possess an anomeric carbohydrate carbon position, these surfactants maintain their reducing nature and are susceptible to further derivatization. They are also synthesized from renewable, economical carbohydrates and lipids and may provide an excellent alternative to pertrochemical-derived products.     

A helical drive in-pipe robot based on compound planetary gearing

The modern society is fuelled by very comprehensive grids of gas and liquid pipelines. In recent years, various in-pipe robots have been developed for inspection and maintenance tasks inside such pipes. In this paper, a novel in-pipe robot is proposed and developed for gas/oil well interventions at thousands of meters downhole. Due to the nature of such intervention, in-pipe robot design must be capable of carrying a very large payload, as large as 2500?N inside a pipe with diameter as small as 54?mm. The proposed design concept is based on a compound planetary gearing system. One of the major novelties of this design is the use of pipe wall as a ring gear for one stage of the compound planetary gear system; the other novelty is the generation of helical angle when the planetary gears are expanded to press on the pipe wall. The proposed concept is compact, efficient, and has never been reported before. In this paper, the helical angle, the velocity, and load capability of the proposed system will be analyzed. The load transportation capability of the proposed robot is also measured based on an experiment. Initial data have shown great potential in carrying large payloads.     

Measurement of the rheological properties of polymer melts with annular rheometer

An annular die has been designed having a very thin gap distance between two coaxial cylinders. The die was then used to measure wall normal stresses along the longitudinal direction of polymer melts flowing through the thin annulus. The materials investigated were high-density polyethylene, low-density polyethylene, polypropylene, and polystyrene. Also investigated were blends of polystyrene and polypropylene, and blends of polystyrene and high-density polyethylene The measurements of wall normal stresses were used to determine the rheological properties of the melts, namely, the melt viscosity from the slope of axial wall normal stress profiles and the melt elasticity from exit pressures. The interpretation of the experimental data was made possible by the fact that the narrow-gap annular die can be considered as a substitute for a thin slit die. It has been found that the results obtained in the present study are consistent with those reported earlier by the author, who at that time used both capillary and slit dies.     

Guerbet十四醇的合成与表征

以正庚醇为原料 ,通过Guerbet反应合成Guerbet十四醇 (2 戊基壬醇 ,C14 GA)。用IR、NMR和元素分析测定了C14 GA的结构 ,并研究了反应温度和用料比对其产率的影响。实验结果如下 :(1)在较优化的反应条件下 (正庚醇的总加入量为 1mol,在实验过程中 ,先加入 1/ 3mol庚醇和 1/ 4mol的KOH ,在 16 0℃下反应 2h ,然后再加入剩下的 2 / 3mol庚醇和 4g 5 %Pd -C催化剂 ,在 15 5℃下反应 6h)合成产物 ,其产率可达到 5 4 2 0 % ;(2 )所合成的产物与试图要得到的Guerbet十四醇 (2 戊基壬醇 ,C14 GA)含有相同的基团 (2×—CH3、10×—CH2 —、1×CH、1×—CH2 —O—和 1×—OH) ,而且 ,所合成的产物中 ,w (C) =79 0 6 % ,w (H ) =13 6 2 % ,与从Guerbet十四醇分子式计算的理论值w(C) =78 5 0 % ,w (H) =14 0 1%基本一致。可见所合成的产物正是Guerbet十四醇 (C14 GA)     

Synthesis and self-assembly of hyperbranched polyester peripherally modified by touluene-4-sulfonyl groups

In this paper, hyperbranched polyesters (HPs) were synthesized in the molten state from 2,2-bis(hydroxymethyl) propionic acid (bis-MPA) and 2-ethyl-2-hydroxymethyl-1,3-propanediol (TMP) using acid catalysis. The modified hyperbranched polyesters were obtained through the chemical modification of the hyperbranched polyester cores by substituting a controlled fraction of the terminal hydroxyl groups with touluene-4-sulfonyl chloride using triethylamine (TEA) as an acceptor of HCl. The resultant polyesters were characterized by ¹H NMR, ¹³C NMR, FT-IR, UV and GPC and their self-assembly behaviors were investigated. The results revealed that self-assembled structures could be formed in selected solvents (trichloromethane/acetone or trichloromethane/n-hexane).     

Industrial TiO2 based nacreous pigments as functional building materials: Photocatalytic removal of NO

In this paper, the photocatalytic activity of industrial titanium dioxide (TiO₂) based nacreous pigments was researched as functional building materials for photocatalytic NO remove. Three industrial TiO₂ based nacreous pigments were selected to estimate the photocatalytic activity for NO remove. This study is a good proof that pearlescent pigments can eliminate NO, and its performance is positively correlated with its titanium dioxide content. And this research will widen the application of nacreous pigments in functional building materials, and provide a new way to eliminate in door nitric oxide pollution.     

多降液管筛板塔的设计计算

简要介绍多降液管筛板塔的特点及塔板参数的设计计算方法。     

Substrate-mediated interactions and intermolecular forces between molecules adsorbed on surfaces

Adsorbate interactions and reactions on metal surfaces have been investigated using scanning tunneling microscopy. The manners in which adsorbates perturb the surface electronic structure in their vicinity are discussed. The effects these perturbations have on other molecules are shown to be important in overlayer growth. Interactions of molecules with surface steps are addressed, and each molecule's electron affinity is shown to dictate its adsorption sites at step edges. Standing waves emanating from steps are demonstrated to effect transient molecular adsorption up to 40 A away from the step edge. Halobenzene derivatives are used to demonstrate how the surface is important in aligning reactive intermediates.