The Effect of Aluminum Ions on the DC Etching of Aluminum Foil

A study has been made of the electrochemical etching of 99.99% aluminum foils at a current density of 50 mA cm^–2in AlCl₃–HCl solutions (1 m Cl^–) at 80 °C. The solutions were made by dissolving metallic aluminum into 1m HCl solution, to give a Cl^– concentration of 1 m. The number density of etch tunnels and the homogeneity of tunnel length decreased, and the mean pit size and its standard deviation increased with increasing Al³⁺ concentration. The results were discussed based on potential transients at a current density of 50 mA cm^–2, current–potential curves at a scan rate of 10 m Vs^–1 and electrochemical impedance spectra.     

利用氯碱厂废弃盐泥制备NO3-吸附剂

将氯碱厂废弃盐泥与丙烯酸、钛酸四正丁酯等共聚，过硫酸钾作引发剂，制得TNO3^-吸附剂，同时还得到了有利用价值的二氧化硅和碳酸钙。用正交试验法与单纯形优化法相结合，确定了废弃盐泥制备NO3^-吸附剂的优良配方及合适的工艺。增添了水净化剂的新品种，探索了氯碱工业废弃盐泥利用的新途径。     

Ceramic Composites with Three-Dimensional Architectures Designed to Produce a Threshold Strength—II. Mechanical Observations

Finite element modeling and linear elastic fracture mechanics are used to model the residual stresses and failure stress of ceramic composites consisting of polyhedral alumina cores surrounded by thin alumina/mullite layers in residual compression. This type of composite architecture is expected to exhibit isotropic threshold strength behavior, in which the strength of the composite for a particular assumed flaw will be constant and independent of the orientation of tensile loading. The results of the modeling indicate that the strengths of such architectures will be higher than those of laminates of similar architectural dimensions that were previously found to exhibit threshold strength behavior for a particular flaw type. Flexural testing of the polyhedral architectures reveals that failure is dominated by processing defects found at junctions between the polyhedra. Fractography revealed the interaction of these defects with the residual stresses in the compressive layers that separate the polyhedra.     

Properties and crystallization kinetics of poly(ether ether ketone)‐co‐poly(ether ether ketone ketone) block copolymers

A series of block copolymers composed of poly(ether ether ketone) (PEEK) and poly(ether ether ketone ketone) (PEEKK) components were prepared from their corresponding oligomers via a nucleophlilic aromatic substitution reaction. Various properties of the copolymers were investigated with differential scanning calorimetry (DSC) and a tensile testing machine. The results show that the copolymers exhibited no phase separation and that the relationship between the glass‐transition temperature (T_g) and the compositions of the copolymers approximately followed the formula T_g = T_g1X₁ + T_g2X₂, where T_g1 and T_g2 are the glass‐transition‐temperature values of PEEK and PEEKK, respectively, and X₁ and X₂ are the corresponding molar fractions of the PEEK and PEEKK segments in the copolymers, respectively. These copolymers showed good tensile properties. The crystallization kinetics of the copolymers were studied. The Avrami equation was used to describe the isothermal crystallization process. The nonisothermal crystallization was described by modified Avrami analysis by Jeziorny and by a combination of the Avrami and Ozawa equations. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1652–1658, 2005     

炭黑对轮胎胎面胶热物性的影响

研究了炭黑品种和用量对轮胎胎面胶热扩散系数(α)、导热系数(λ)及比热容(C)3种热物性参数的影响规律。结果表明,随着炭黑填充量的增加,胎面胶的α及λ均逐渐增大,C逐渐减小。炭黑的结构性对胎面胶α的影响程度大于炭黑的粒径;温度相同时,炭黑的结构性越高,其填充胎面胶的α越大;随着炭黑填充量的增加,3种炭黑填充胎面胶α之间的差距呈现先增大后减小的变化趋势。炭黑的结构性及粒径对胎面胶C的影响没有固定的规律,但在低温区,炭黑的粒径越大,其填充胎面胶的C越大,且炭黑填充量对此差距无影响。炭黑的结构性对胎面胶λ的影响程度大于炭黑的粒径;温度相同时,炭黑的结构性越高,其填充胎面胶的λ越大;当炭黑用量较低时,其对胎面胶λ的影响程度相对较小,随着炭黑填充量的增加,3种炭黑填充胎面胶λ之间的差距呈现先增大后减小的变化趋势。     

Immobilization of a cyclodextrin glucanotransferase (CGTase) onto polyethylene film with a carboxylic acid group and production of cyclodextrins from corn starch using CGTase‐immobilized PE film

Carboxylic acid groups were introduced onto polyethylene (PE) film by radiation‐induced graft copolymerization. Subsequently, the clodextrin glucanotransferase (CGTase) was immobilized on the PE film with a carboxylic acid group. The activity of the immobilized CGTase on PE film was in the range of 0.40–1.04 U/cm² per min. The production of cyclodextrins (CDs) from corn starch was examined using the CGTase‐immobilized PE film. The production ratios of CDs using CGTase‐immobilized PE film was in the following order: α–CD > β–CD > γ–CD. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 2451–2457, 2002     

新试剂DBPMP用于铀的萃取光度法测定研究

本文将新型螯合萃取剂DBPMP用于铀的萃取光度法研究。提出了一种选择性好,灵敏度高的测定方法。铀浓度在0～5.0mg/25ml范围内符合比尔定律。将本法用于矿石中铀的测定,结果满意。     

光波导加速度传感器中3dB耦合器设计

光波导加速度传感器是一种实用型加速度传感器,目前广泛应用制备光学加速度计的迈克尔逊、马赫—曾德等干涉仪的核心部件都包含3 dB耦合器。3 dB耦合器的设计对光波导加速度传感器的检测精度尤为重要。介绍了所设计的光波导加速度传感器的工作原理,设计了3 dB耦合器波导的结构和参数,并用光学模拟软件OptiBPM对3 dB耦合器进行模拟。结果表明:所设计的3dB耦合器具有良好性能,符合设计要求。     

Effect of the processing molding temperature on the crystalline structure and properties of acrylonitrile‐butadiene rubber/trinylon thermoplastic vulcanizates

The effect of the processing molding temperature on the properties and crystalline structure of acrylonitile‐butadiene rubber (NBR)/nylon 6,66,1010 (trinylon) thermoplastic vulcanizates (TPV) was studied. With decreasing molding temperature, the stress at 100% and elongation at break of TPV changed slightly, and the solvent resistance of TPV improved. The best conditions for processing molding were 170°C and 12 min. The crystalline structure of the nylon continuous phase in TPV was investigated by X‐ray diffraction, polarized optical microscopy, and differential scanning calorimetry. The results show that the crystalline structure of the nylon phase in TPV was more perfect/orderly and formed α‐crystalline structure at a processing molding temperature of 170°C. Therefore, the oil resistance of NBR/trinylon TPV clearly improved. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 1374–1379, 2006     

CO2在绿色化学合成中的应用

研究了CO2在绿色化学合成中的应用.CO2作为酸碱调节剂和惰性气体,在β-胡萝卜素催化氧化合成角黄素反应中,可以控制反应体系酸性,保护原料中的双键,减少副反应发生,提高催化氧化反应的选择性;异戊二烯氯醇化生成1-氯-2-甲基-3-丁烯-2-醇和1-氯-2-甲基-3-丁唏-4-醇反应中,CO2代替有机酸作酸碱调节剂,控制次氯酸的生成速度,达到调控反应的目的,反应条件温和,不副产固体.