Oxidation behavior and mechanism of aluminum oxynitride (AlON) at elevated temperatures

The oxidation behavior and mechanism of aluminum oxynitride (AlON) powder exposed to air at elevated temperatures between 800°C and 1300°C was investigated by X-ray diffractometry (XRD), scanning electron microscope (SEM), electron spin resonance (ESR), nuclear magnetic resonance (NMR), and simultaneous thermogravimetry, differential thermal analysis, and mass spectrometry techniques (TG-DTA-MS). The weight of AlON gradually increases to a maximum value at 1150°C and then decreases with further heating. Meanwhile, AlON powder undergoes chemical changes, as evidenced by lattice expansion, and turns eventually into alumina. ESR spectra reveal the occurrence of lone pair electrons in the oxidized products and the intensity of corresponding resonance signal increases before disappearing with the increase in temperature. Combined with the results of NMR and TG-DTA-MS, the measured data suggest that Al-N in [AlO₃N] tetrahedron and [AlO₅N] octahedron are gradually oxidized into Al-O-N group with lone pair electrons, which causes continuous weight gain and lattice expansion. Further oxidation at higher temperatures results in alumina and N₂.     

Electrochemical properties of some cobalt antimonides as anode materi-als for lithium- ion batteries

Some cobalt antimonides have been prepared and studied as the candidate anode materials for lithium ion batter-ies. Reversible capacities of 424,423 and 546 mA·h·g-1 were measured at the first cycle for as-solidified CoSb2, CoSb3 and annealed CoSb3 respectively. A low lithium ions diffusion coefficient in the order of 10-16 m2·s-1 was estimated from the coulometric titration measurements in the annealed CoSb3 electrode. It was found that the electrochemical properties of fine powders are significantly better than coarse powders. However the SEM picture shows that the nano-sized CoSb3 powders gathered to larger granules, which worsens somewhat the capacity retention of the nano-sized materials, although the volume capacities of the annealed and ball milled CoSb3 remain near twice of that of graphite after 50 cycles.     

On the mechanical performance of closed cell Al alloy foams

The mechanical properties of three different commercially available closed cell Al alloys all made by foam casting are examined. The objective is to assess the roles of cell morphology and of imperfections in governing the basic properties: stiffness, yield strength and fracture resistance. This assessment provides goals for manufacturing strategies that enable attainment of good mechanical performance with affordable process technologies. A prevalent role of curves and wiggles in the cell walls on stiffness and strength (anticipated by models) is affirmed by the present measurements. Systematically larger stiffnesses and yield strengths found in tension than in compression are consistent with a prominent role exerted by such imperfections. Moreover, foam casting is apparently capable of cell morphologies that impart properties approaching the best achievable values for an isotropic closed cell solid, devoid of imperfections. There are associated implications for performance and affordability. Fracture measurements indicate crack growth occurring along the cell walls by a mechanism analogous to the plastic tearing of thin sheets. The crack growth resistances are in the range of 1 kJm⁻². This mechanism infers a toughness that scales with the cell wall thickness and its yield strength.     

易门铜业公司18kt／a粗铜及硫酸车间的技改工程

介绍了易门铜冶炼厂烟气制酸系统的技术改造工程.从工艺流程、设备复核、工艺参数、设备配置等方面阐述了技改的过程.     

钨钴硬质合金电化学蚀刻加工研究

对YG6硬质合金电化学蚀刻工艺进行了研究,提出了采用光致抗蚀剂作保护膜,在生成一定钝化膜的情况下进行电化学蚀刻的方法.在一定的蚀刻深度范围内,该工艺的可控性好、腐蚀区表面质量较好.     

探索中国民营企业经营模式创新之路——岷山公司推行模拟法人经营体制

中国民营企业经营现状据第一部《中国民营企业发展报告》蓝皮书统计，中国300多万家私营企业90％以上是家族企业，既有单一业主制的企业，也有合伙制的企业、共有制的企业，甚至还出现了家族成员保持临界控制权的企业集团。     

用于预焙槽炼铝的多功能地面专用操作设备

主要介绍了预焙槽炼铝另外一种操作方式的专用设备———多功能地面操作车辆 ,分别对更换阳极打壳专用车、阳极覆盖加料车、出铝叉车进行了介绍 ,并总结了这些操作设备的优点及对我国铝工业的可借鉴之处。     

TEM IMAGING TECHNIQUE

This imaging technique is used for approximate interpretation of TEM data including ungrounded loopsource and grounded line source soundings.Loop source data can be collected as central-loop soundings or asout-of-loop soundings with a short or long offset configuration.The imaging method is based on the same princi-ple as that employed by Fullager(1989),with apparent resistivities computed directly from time-derivative data,db/d,and then associated with depths according to image theory.     

激光快速成形Rene′88DT高温合金的时效强化研究

研究了时效时间对激光快速成形后时效硬化镍基高温合金Rene′88DT中沉淀相组织演化和力学性能的影响。发现随时效时间的增加，沉淀相y’略有长大，颗粒之间发生大颗粒吞噬小颗粒的粗化，时效40h后沉淀相颗粒粗化明显。对经不同时间时效后的激光快速成形Rene′88DT试样进行了硬度测试。结果显示，在时效时间为28h时，硬度有一峰值HRC49。在此基础上，采用1165℃，2h固溶、空冷＋760℃，28h时效的热处理工艺对激光快速成形标准拉伸棒样进行了热处理，拉伸结果显示成形件的抗拉强度较激光沉积态提高了400MPa，屈服强度接近同种材料的粉末锻造水平。     

含B2O3渣系的热力学计算模型

根据炉渣结构的共存理论和相图，推导了ＣａＯＢ２Ｏ３和ＦｅＯＦｅ２Ｏ３Ｂ２Ｏ３渣系的热力学计算模型。结果表明：（１）理论计算的ＣａＯＢ２Ｏ３渣系的作用浓度ＮＣａＯ及ＮＢ２Ｏ３与实测的活度ａＣａＯ及ａＢ２Ｏ３一致；（２）理论计算的ＦｅＯＦｅ２Ｏ３Ｂ２Ｏ３渣系的氧化能力ＮＦｅｔＯ与实测的炉渣ＦｅｔＯ的活度值相符合。这说明本文提出的热力学计算模型是合理的。