混合物MH-81状态方程的研究——从无限稀释活度系数预测混合物汽液平衡

本文由无限稀释活度系数求取混合物MH-81状态方程的二元相互作用参数,预测了二元混合物的汽液平衡,获得了较满意的结果。     

Structural topology optimization with constraints on multi-fastener joint loads

This paper addresses an important problem of design constraints on fastener joint loads that are well recognized in the design of assembled aircraft structures. To avoid the failure of fastener joints, standard topology optimization is extended not only to minimize the structural compliance but also to control shear loads intensities over fasteners. It is shown that the underlying design scheme is to ameliorate the stiffness distribution over the structure in accordance with the control of load distributions over fastener joints. Typical examples are studied by means of topology optimization with joint load constraints and the standard compliance design. The effects of joint load constraints are highlighted by comparing numerical optimization results obtained by both methods. Meanwhile, resin models of optimized designs are fabricated by rapid prototyping process for loading test experiments to make sure the effectiveness of the proposed method.     

Damping of vinyl acetate–n‐butyl acrylate copolymers

A photopolymerization process at room temperature was devised to copolymerize vinyl acetate (VAc) and n‐butyl acrylate (BA) mainly to prepare rubber‐like damping sheet bearing pressure‐sensitive adhesive property in this study. The investigations using both the differential scanning calorimeter and rheometric dynamic analysis show the existence of two glass transition temperatures for each copolymer. The scanning electron microscopic pictures reveal that the degree of microphase separation increases with increasing annealing time at 70°C. It was suggested that the rubbery domain (formed by the PBA blocks) disperses in the glassy domain (constituted by the PVAc blocks), making an effective damping entity. Excellent damping was observed for the copolymer samples, with the tanδ peak values as high as 1.76–1.80 at a certain temperature range and with tanδ> 0.3 at quite wide temperature ranges. In addition, the copolymers containing more VAc tend to have the higher damping. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 91: 1396–1403, 2004     

染料及中间体生产中的治理方法三废(Ⅰ)

由于我国染料及中间体行业近三十年来发展迅猛,而染料企业大多数是小型厂,染料品种繁多,在化工系统中,这一行业目前几乎是污染最严重、污染面最大、治理最差的。同时,一些发达国家把污染重、难治理的产品关停,转向发展中国家生产,染料中间体便是其中之一。所以我国大量的小型乡镇企业治理难度就更大了。不同染料生产原料、工艺过程不同,所排“三废”即有共同的特性,又有各自特点,因此需要针对各自的不同分别处理。本文从废气、有机废液和废渣、废水三方面详细叙述了工业上常用的治理方法及适用条件。并例举了几类排放量较大的废水的治理方法。     

Degradation of acrylonitrile–ammonium itaconate copolymers

Acrylonitrile–ammonium itaconate copolymers were prepared by H₂O/dimethyl formamide suspension polymerization technique. Differential scanning calorimetry results of the degradation of acrylonitrile–ammonium itaconate copolymers in air are presented. The apparent activation energy of degradation of the copolymer was calculated using the Kissinger method. Effects of copolymerization conditions on the apparent activation energy of copolymer were studied. Increasing the dimethyl formamide concentration in the solvent mixture leads to a rapid increase in the degradation apparent activation energy of acrylonitrile–ammonium itaconate copolymer. The value of the degradation apparent activation energy of the copolymer synthesized in dimethyl formamide solvent increases up to 168.3 kJ mol^?1. The apparent activation energy decreases quickly along with an increase in ammonium itaconate concentration, and this change becomes less prominent as the weight ratio of ammonium itaconate/acrylonitrile goes beyond 6/94, ΔE_a = 89.4 ± 2.0 kJ mol^?1. The apparent activation energy shows a trend of increase with increasing copolymerization temperature. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1708–1711, 2005     

Dynamic viscoelasticity of low‐density polyethylene/in‐situ‐grafted carbon black composite

The study on the dynamic viscoelastic properties of grafted carbon black (g‐CB) filled low‐density polyethylene (LDPE) was carried out. Because of formation of CB networking, the characteristic modulus plateau and loss tangent arc appears. Addition of grafting monomer like butyl acrylate (BA) and acroleic acid (AA) enhances the interaction between particles and matrix due to accelerated formation of micronetworking in the composites induced by forming branch chains of AA and BA with multiunit. The decrease of the temperature corresponding to α_c mechanical relaxation together with AA (BA) addition given by the position of loss tangent (tan δ) peak for LDPE is owed to the formation of long‐chain polymer grafted between CB and the matrix, which facilitates the slip of the lamella of LDPE. The influence of maleic anhydride (MA) on enhancing interaction between LDPE and CB is not so pronounced, as compared with AA and BA because of no formation of long chain between CB particle and polymer matrix. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 4127–4132, 2006     

SPE-快速分离柱HPLC法测定枸杞样品中的类胡萝卜素

研究了固相萃取(SPE)富集和预分离,快速分离柱高效液相色谱(HPLC)快速测定枸杞样品中类胡萝卜素的新方法;枸杞样品中的类胡萝卜素用W aters Sep-Pak C18固相萃取小柱预分离,然后以ZORBAX Stab leBound(4.6 mm×50 mm,1.8μm)快速分离柱为固定相,甲醇-四氢呋喃为流动相分离,V(甲醇)∶V(四氢呋喃)=80∶20,用二极管矩阵检测器检测,检测波长为450 nm,枸杞样品中的几种类胡萝卜素在5 m in内可达到基线分离,比常规方法节约时间75%左右。方法标准回收率为95%~103%,RSD为1.9%~2.6%。     

Synthesis and Morphology of TiO2 Nanotube Arrays by Anodic Oxidation Using Modified Glycerol-Based Electrolytes

Titanium dioxide (TiO₂) nanotube arrays were prepared by electrochemical anodization of titanium sheets in the glycerol 176 mL/H₂O 44 mL/NH₄F 0.5 wt% electrolytes modified with H₂SO₄ and NaAc addition. The surface morphologies, average inner diameter, and the length of the nanotube arrays changed with the solution pH in the range from 5.6 to 4.0 by adding H₂SO₄. A uniform surface morphology of the nanotubes with average inner diameter of ∼80 nm and a length of ∼1000 nm was obtained when the solution pH was 5.0. The growth rates of the nanotubes were remarkably enhanced by NaAc addition in the range of 0.04–0.14 M . With NaAc addition of 0.10 M , the length of the nanotube arrays reached 4.16 μm after an 8-h anodization, increasing 3.23 μm compared with no NaAc addition. The relationship between solution pH and growth of TiO₂ nanotubes was analyzed by current–time curves, solution electrical conductivities, and scanning electron microscopy (SEM), and the role of NaAc was also discussed based on SEM and solution electrical conductivities.     

网络冗余技术在公司局域网的应用分析

随着SG186系统建设不断向企业的覆盖与延伸,信息网络的强健与否成为制约信息化系统应用的重要因素。本文通过对网络冗余技术的介绍,结合公司信息网络结构实际情况,通过应用实例分析,阐述如何合理使用网络冗余技术,确保信息网络的高可靠性。     

Synthesis and light‐emitting properties of new poly(p‐phenylenevinylene) derivatives containing oxadiazole moiety

Two new poly(p‐phenylenevinylene) (PPV) derivatives containing oxadiazole moiety (OXA‐PPV1 and OXA‐PPV2) were synthesized by the Wittig condensation polymerization reaction. Their thermal and light‐emitting properties were investigated. The single‐ and triple‐layer electroluminescent (EL) devices with configurations of ITO/polymer/Al and ITO/polymer/OXD‐7/Alq₃/Al were fabricated. They exhibited blue emission at 470 nm for OXA‐PPV1 and green emission at 560 nm for OXA‐PPV2. The turn‐on voltages of triple‐layer device were 11 V for OXA‐PPV1 and 8 V for OXA‐PPV2. The triple‐layer EL devices showed much better performance than did the single‐layer devices. The spectra indicated energy transfer occurred from segments of side chain to polymer backbone. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 422–428, 2002