降维方法监督分类的比较研究

对ISOMap、LDA、LLE、PCA这4种典型降维算法的主要思想和算法步骤进行了详细分析,并将它们用于有监督分类。从实验结果分析得到结论 ,其可为有监督分类提供有益的借鉴。     

Preparation and Photoluminescence of Partially Filled ZnO Microtubes Using Block Copolymers

Partially filled ZnO microtubes were synthesized in large scale using block copolymers. The growth mechanism of this unique construction is proposed on the basis of adsorption of block copolymers on {0002} plane of wurtzite ZnO. The photoluminescence property of these unique ZnO microtubes is also studied using a Xe lamp as the excitation source at room temperature. Blue emission band at 425 nm is a much stronger ultraviolet emission band, which is due to laminar structure of ZnO microtubes.     

炭黑填充硬聚氯乙烯的改性

为使聚氯乙烯具有抗静电性能,采用加入具有导电性填料的方法,但加入大量的填料,会使硬聚氯乙烯的冲击性能降低,加工性能变差。本文是在以炭黑为填料的基础上,研究不同的改性剂和加工助剂改进硬聚氯乙烯的效果,结果表明,加入冲击改性剂和加工助剂后,大大增加了硬聚氯乙烯的冲击强度,且加工性能也得到改善,同时由于炭黑具有补强效果,其拉伸强度和弯曲强度在加入改性剂后也能满足使用要求。     

Kinetics for benzoylation of sodium 4-acetylphenoxide via third-liquid phase in the phase-transfer catalysis

In this research, the kinetics for synthesizing 4-acetylphenyl benzoate (R^*COOR) from benzoylation of sodium 4-acetylphenoxide via third-liquid phase-transfer catalysis was investigated. The reaction rate was observed to be strongly dependent on agitation speeds in the third-phase catalytic reaction. By forming the third-liquid phase, the observed reaction can be greatly enhanced to give a product yield of 100% in a duration of 3 min at 20 °C and 200 rpm. If a third-liquid phase was not formed in the liquid–liquid system, the reaction rate is very slow and the product yield is only 2% in 3 min at 20 °C. The reaction conducted in third-liquid phase-transfer catalytic system is faster than that in LLPTC system by 25–28 times. The amount of catalytic intermediate (QOR) in the third-liquid phase was about 50% of the catalyst initially added and kept about 30% of it remained after 1 min, and only small amounts of a catalytic intermediate residing in the organic phase were observed during the reaction using methyl t-butyl ether as the solvent. The concentration of catalytic intermediate slightly decreased with increasing reaction time, while the molar ratio of QOR to benzyl tri-n-butylammonium cation in the third-liquid phase remained almost constant after 1 min and increased with increasing agitation speeds. The experimental results were well described by the pseudo-first-order kinetics. The present work shows an effective method to synthesize 4-acetylphenyl benzoate.     

基于Web的重点建设项目管理系统

为提高重点建设项目的管理水平和工作效率,在详细分析重点建设项目的业务流程和用户需求的基础上,提出基于Web的重点建设项目信息管理系统。该系统采用典型的三层体系架构,具有较强的可扩展性和灵活性。通过该系统对重点建设项目信息科学管理,可以有效克服传统管理方式的弊端,极大地提高重点建设项目信息管理工作的效率。     

Synthesis of Biodiesel from Soybean Oil using Heterogeneous KF/ZnO Catalyst

Biodiesel was produced by transesterification of soybean oil with methanol using ZnO loaded with KF as a solid base catalyst. It was found that the catalyst with 15 wt.% KF loading and calcined at 873 K showed the optimum activity. XRD, IR and Hammett indicator method were employed for the catalyst characterization. The results showed the activity of the catalysts was correlated with their basicity. The influence of various reaction variables on the conversion was also discussed.     

Facile preparation of amphiphilic oxyethylene-oxypropylene block copolymers by selective triazine coupling

A novel synthetic route for preparing high molecular weight poly(oxyalkylene) block copolymers has been developed by using 2,4,6-trichloro-1,3,5-triazine (cyanuric chloride, cc) as the coupling core. The coupling reaction involves the selective substitutions of oligo(oxyalkylene)-amines onto three chlorides of the triazine ring in a stepwise manner at 0, 25 and 130 °C. By judiciously selecting the starting amines and reaction conditions, one can tailor the copolymer structures with different block configurations (tri-block, multi-block, random and alternating block). The prepared copolymers can have a high molecular weight, up to 25,600 g/mol (GPC polydispersity=1.48), and also high thermal stability due to the presence of triazine functionalities. The copolymers with hydrophilic and hydrophobic oligo(oxyalkylene) blocks are of versatile properties in solubility (water soluble or water insoluble) and morphology (crystalline or amorphous). With a specific structure of alternating oligo(oxyethylene)/oligo(oxypropylene) blocks (2000 g/mol each block), the copolymer exhibits the property of self-association. It reduces the interfacial tension of toluene/water as low as 0.5 dyne/cm at the critical micelle concentration of 0.01 wt%.     

Preparations and properties of thermosensitive terpolymers of N‐isopropylacrylamide,sodium 2‐acrylamido‐2‐methyl‐propanesuphonate,and N‐tert‐butylacrylamide

Terpolymers based on N‐isopropylacrylamide, sodium 2‐acrylamido‐2‐methyl‐propanesulfonate, and N‐tert‐butylacrylamide were synthesized by free‐radical copolymerization with 2,2′‐azobisisobutyronitrile as an initiator. The lower critical solution temperatures (LCSTs) of the linear polymer aqueous solutions were determined by the measurement of the transmittance on UV at different temperatures. The influence of the polymer concentration, polymer composition, and ionic strength on the LCSTs of the linear polymers was investigated. The LCST decreased with increases in the hydrophobic monomer N‐tert‐butylacrylamide, polymer concentration, and ionic strength. The phase transition became sharp when the polymer concentration and ionic strength increased. Meanwhile, the crosslinked hydrogels were prepared with the same recipe used for the linear terpolymers, but a crosslinker was added to the reaction system. The swelling ratios of the hydrogels at various temperatures and salt solutions were determined. The hydrogels possessed both high swelling ratios and thermosensitivity. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Preparation of Titanium Nitride/Alumina Laminate Composites

A preparation route for TiN/Al₂O₃ laminate composites has been described. A water-based process using Al₂O₃ and TiN slurries with solids contents of 40 and 35 vol%, respectively, was used to make TiN and Al₂O₃ tapes. The removal of the binder was monitored by weight-loss measurements in a thermogravimetry unit. Bodies composed of Al₂O₃ and TiN tapes were densified at temperatures of 1400° and 1500°C using the Spark Plasma Sintering^® (SPS) technique. Densities of >98% of the theoretical densities were approached. Crack-free and almost fully densified TiN/Al₂O₃ compacts were prepared by heating the burned-out green bodies to the final sintering temperature (1500°C) at a rate of 100°C/min, and with a holding time of 5–10 min, under a pressure of 75 MPa. The microstructures of the obtained compacts were studied using scanning electron microscopy. Grain sizes in the sintered Al₂O₃ and TiN compacts were similar to those of the precursor powders. Hardness and indentation fracture toughness were measured at room temperature, and the monolithic compacts as well as the laminate composites exhibited anisotropic mechanical behavior; i.e., the cracks propagated much more easily in a direction parallel to the laminas than perpendicular to them.     

Stability analysis and controller synthesis for discrete uncertain singular fuzzy systems with distinct difference matrices in the rules

This paper mainly studies an extended discrete singular fuzzy model incorporating the multiple difference matrices in the rules and discusses its stability and design issues. By embracing additional algebraic constraint, traditional discrete Takagi-Sugeno (T-S) fuzzy model can be extended to a generalised discrete singular Takagi-Sugeno (GDST-S) model with individual difference matrices E_i in the locally singular models, where it can describe a larger class of physical or non-linear systems. Based on the linear matrix inequality (LMI) approach, we focus on deriving some explicit stability and design criteria expressed by the LMIs for the regarded system. Thus, the stability verification and controller synthesis can be performed by the current LMI tools. Finally, some illustrative examples are given to illustrate the effectiveness and validity of the proposed approach.