Preparation and Photoluminescence of Partially Filled ZnO Microtubes Using Block Copolymers

Partially filled ZnO microtubes were synthesized in large scale using block copolymers. The growth mechanism of this unique construction is proposed on the basis of adsorption of block copolymers on {0002} plane of wurtzite ZnO. The photoluminescence property of these unique ZnO microtubes is also studied using a Xe lamp as the excitation source at room temperature. Blue emission band at 425 nm is a much stronger ultraviolet emission band, which is due to laminar structure of ZnO microtubes.     

炭黑填充硬聚氯乙烯的改性

为使聚氯乙烯具有抗静电性能,采用加入具有导电性填料的方法,但加入大量的填料,会使硬聚氯乙烯的冲击性能降低,加工性能变差。本文是在以炭黑为填料的基础上,研究不同的改性剂和加工助剂改进硬聚氯乙烯的效果,结果表明,加入冲击改性剂和加工助剂后,大大增加了硬聚氯乙烯的冲击强度,且加工性能也得到改善,同时由于炭黑具有补强效果,其拉伸强度和弯曲强度在加入改性剂后也能满足使用要求。     

Kinetics for benzoylation of sodium 4-acetylphenoxide via third-liquid phase in the phase-transfer catalysis

In this research, the kinetics for synthesizing 4-acetylphenyl benzoate (R^*COOR) from benzoylation of sodium 4-acetylphenoxide via third-liquid phase-transfer catalysis was investigated. The reaction rate was observed to be strongly dependent on agitation speeds in the third-phase catalytic reaction. By forming the third-liquid phase, the observed reaction can be greatly enhanced to give a product yield of 100% in a duration of 3 min at 20 °C and 200 rpm. If a third-liquid phase was not formed in the liquid–liquid system, the reaction rate is very slow and the product yield is only 2% in 3 min at 20 °C. The reaction conducted in third-liquid phase-transfer catalytic system is faster than that in LLPTC system by 25–28 times. The amount of catalytic intermediate (QOR) in the third-liquid phase was about 50% of the catalyst initially added and kept about 30% of it remained after 1 min, and only small amounts of a catalytic intermediate residing in the organic phase were observed during the reaction using methyl t-butyl ether as the solvent. The concentration of catalytic intermediate slightly decreased with increasing reaction time, while the molar ratio of QOR to benzyl tri-n-butylammonium cation in the third-liquid phase remained almost constant after 1 min and increased with increasing agitation speeds. The experimental results were well described by the pseudo-first-order kinetics. The present work shows an effective method to synthesize 4-acetylphenyl benzoate.     

Synthesis of Biodiesel from Soybean Oil using Heterogeneous KF/ZnO Catalyst

Biodiesel was produced by transesterification of soybean oil with methanol using ZnO loaded with KF as a solid base catalyst. It was found that the catalyst with 15 wt.% KF loading and calcined at 873 K showed the optimum activity. XRD, IR and Hammett indicator method were employed for the catalyst characterization. The results showed the activity of the catalysts was correlated with their basicity. The influence of various reaction variables on the conversion was also discussed.     

Facile preparation of amphiphilic oxyethylene-oxypropylene block copolymers by selective triazine coupling

A novel synthetic route for preparing high molecular weight poly(oxyalkylene) block copolymers has been developed by using 2,4,6-trichloro-1,3,5-triazine (cyanuric chloride, cc) as the coupling core. The coupling reaction involves the selective substitutions of oligo(oxyalkylene)-amines onto three chlorides of the triazine ring in a stepwise manner at 0, 25 and 130 °C. By judiciously selecting the starting amines and reaction conditions, one can tailor the copolymer structures with different block configurations (tri-block, multi-block, random and alternating block). The prepared copolymers can have a high molecular weight, up to 25,600 g/mol (GPC polydispersity=1.48), and also high thermal stability due to the presence of triazine functionalities. The copolymers with hydrophilic and hydrophobic oligo(oxyalkylene) blocks are of versatile properties in solubility (water soluble or water insoluble) and morphology (crystalline or amorphous). With a specific structure of alternating oligo(oxyethylene)/oligo(oxypropylene) blocks (2000 g/mol each block), the copolymer exhibits the property of self-association. It reduces the interfacial tension of toluene/water as low as 0.5 dyne/cm at the critical micelle concentration of 0.01 wt%.     

Fabrication and amplification of Rhodamine B‐doped step‐index polymer optical fiber

A step‐index polymer optical fiber (SI POF) containing Rhodamine B in poly(methyl methacrylate) (PMMA) has been fabricated by a preform technique. Fluorescence of different fiber lengths were observed and discussed. A high gain (23 dB) for a SI POF with 60‐cm length, 400‐μm diameter was obtained. The Rhodamine B content of the doped SI POF is 5 ppm‐wt. The signal wavelength providing the highest gain for a 60 cm SI POF is around 630 nm, and the optimum fiber length is about 60 cm at 10 kW launched pump power. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 93: 681–685, 2004     

Preparation of Titanium Nitride/Alumina Laminate Composites

A preparation route for TiN/Al₂O₃ laminate composites has been described. A water-based process using Al₂O₃ and TiN slurries with solids contents of 40 and 35 vol%, respectively, was used to make TiN and Al₂O₃ tapes. The removal of the binder was monitored by weight-loss measurements in a thermogravimetry unit. Bodies composed of Al₂O₃ and TiN tapes were densified at temperatures of 1400° and 1500°C using the Spark Plasma Sintering^® (SPS) technique. Densities of >98% of the theoretical densities were approached. Crack-free and almost fully densified TiN/Al₂O₃ compacts were prepared by heating the burned-out green bodies to the final sintering temperature (1500°C) at a rate of 100°C/min, and with a holding time of 5–10 min, under a pressure of 75 MPa. The microstructures of the obtained compacts were studied using scanning electron microscopy. Grain sizes in the sintered Al₂O₃ and TiN compacts were similar to those of the precursor powders. Hardness and indentation fracture toughness were measured at room temperature, and the monolithic compacts as well as the laminate composites exhibited anisotropic mechanical behavior; i.e., the cracks propagated much more easily in a direction parallel to the laminas than perpendicular to them.     

直纺长丝工艺中聚酯熔体端羧基值控制的工业研究

本文从工业生产的实践出发对杜邦聚酯技术直接纺工艺中端羧基控制进行了研究。通过对熔体端羧基值对无油长丝端羧基、粘度及纺丝加工影响的分析 ,阐明了聚酯端羧基控制范围 ;通过摸索三个反应釜工艺条件对端羧基值的影响 ,找出了端羧基工业控制的有效途径 ,为同类技术装置生产提供了依据     

Stability analysis and controller synthesis for discrete uncertain singular fuzzy systems with distinct difference matrices in the rules

This paper mainly studies an extended discrete singular fuzzy model incorporating the multiple difference matrices in the rules and discusses its stability and design issues. By embracing additional algebraic constraint, traditional discrete Takagi-Sugeno (T-S) fuzzy model can be extended to a generalised discrete singular Takagi-Sugeno (GDST-S) model with individual difference matrices E_i in the locally singular models, where it can describe a larger class of physical or non-linear systems. Based on the linear matrix inequality (LMI) approach, we focus on deriving some explicit stability and design criteria expressed by the LMIs for the regarded system. Thus, the stability verification and controller synthesis can be performed by the current LMI tools. Finally, some illustrative examples are given to illustrate the effectiveness and validity of the proposed approach.     

A generalized method for correcting instrument spreading in gel permeation chromatography

A general method of chromatogram correction for skewed instrument spreading in gel permeation chromatography is presented. The correction method is so general that there is no restriction on the shape of the spreading function. It admits nonsymmetric, non-Gaussian as well as nonconvolution type. Aspects of solution techniques are discussed and an illustrative example is given to elucidate the method.