CHARAC TERIZATION OF TiAl POWDER PRODUCED BY MECHANICAL ALLOYING

The microstructure,alloying reaction and sintering behavior of the powder produced by Mechanical Al-loying(MA)for 8 h from 64 wt.-% Ti powder and 36 wt.-% Al powder were studied by scanning electronmicroscopy,optical microscopy,X-ray diffractometry,differential scanning calorimetry(DSC)and dilatometry.The mechanically alloyed powder partictes are Ti-Al composite particles.Thus,titanium aluminides can formeasily in the powder through diffusion during heat treatment.It is shown that the sintering behavior of this pow-der,different from the behaviors of TiAl alloy powder and mixed powder of 64 wt.-% Ti powder and 36 wt.-%Al powder,changes from expansion at temperatures below 1000℃ to shrinkage at temperatures above 1000℃.Homogeneously alloyed TiAl material with a density over 96% of the theoretical density can be produced fromthe mechanically alloyed powder by compaction-sintering.     

Water-soluble and amphiphilic polymers

Summary Three PEO-PSt-PEO triblock polymers and their parent ho-nopolystyrene have been studied by means of light scattering technique in chloroform, toluene and ethyl acetate. It has been found that the weight average molecular weights calculated by using the equation Mapp- were unbelievable negative values; and the largest deviation appeared for the sample with PEO mole content of about 50%. Data of PSt-PEO-PSt triblock polymers in literature have been quoted and discussed.     

Guerbet十四醇的合成与表征

以正庚醇为原料 ,通过Guerbet反应合成Guerbet十四醇 (2 戊基壬醇 ,C14 GA)。用IR、NMR和元素分析测定了C14 GA的结构 ,并研究了反应温度和用料比对其产率的影响。实验结果如下 :(1)在较优化的反应条件下 (正庚醇的总加入量为 1mol,在实验过程中 ,先加入 1/ 3mol庚醇和 1/ 4mol的KOH ,在 16 0℃下反应 2h ,然后再加入剩下的 2 / 3mol庚醇和 4g 5 %Pd -C催化剂 ,在 15 5℃下反应 6h)合成产物 ,其产率可达到 5 4 2 0 % ;(2 )所合成的产物与试图要得到的Guerbet十四醇 (2 戊基壬醇 ,C14 GA)含有相同的基团 (2×—CH3、10×—CH2 —、1×CH、1×—CH2 —O—和 1×—OH) ,而且 ,所合成的产物中 ,w (C) =79 0 6 % ,w (H ) =13 6 2 % ,与从Guerbet十四醇分子式计算的理论值w(C) =78 5 0 % ,w (H) =14 0 1%基本一致。可见所合成的产物正是Guerbet十四醇 (C14 GA)     

熔融石英耐火材料

阐述了熔融石英耐火材料的主要性能与应用领域。     

CaSO_4晶须对聚氨酯胶粘剂性能影响的研究

用实验室自制的相对分子质量为2500的聚己二酸-1,4-丁二醇酯二醇和甲苯二异氰酸酯、混合扩链剂配制聚氨酯胶粘剂,并使用实验室自制的改性和未改性200nm硫酸钙晶须对聚氨酯胶粘剂进行改性,考察不同硫酸钙晶须及其加入量、加入方式对聚氨酯胶粘剂综合力学性能的影响。根据实验结果,200nm改性硫酸钙晶须当加入量为3％时,聚氨酯胶粘剂的拉伸强度、初粘性和最终剥离强度均有明显提高。     

直纺长丝工艺中聚酯熔体端羧基值控制的工业研究

本文从工业生产的实践出发对杜邦聚酯技术直接纺工艺中端羧基控制进行了研究。通过对熔体端羧基值对无油长丝端羧基、粘度及纺丝加工影响的分析 ,阐明了聚酯端羧基控制范围 ;通过摸索三个反应釜工艺条件对端羧基值的影响 ,找出了端羧基工业控制的有效途径 ,为同类技术装置生产提供了依据     

基于PXI总线的LVDS数据采集存储模块的设计

鉴于SAR原始数据量大以及数据传输速率限制的问题,设计了基于PXI的雷达回波和图像数据实时记录模块。大容量数据采集记录系统基于通用的商业PC平台设计,选用FPGA作为主控芯片对电路整体逻辑进行控制;利用LVDS作为数据传输接口对数据进行接收,实现了数据采集、缓存以及通过PXI总线上传至上位机硬盘,以便后续处理。文中介绍了系统方案的总体设计,以及采集存储硬件电路的设计,并对电路的关键技术给以详细的分析。     

广角摄像机在机器人视觉定位中的应用

为了保证广角摄像机在现代机器人视觉定位应用中的准确性,以广角摄像机像素坐标的反畸变过程为研究对象,提出一种在畸变对应表的基础上使用中心迭代法以及区域插值法确定物体实际位置的方法。通过实验证明了该方法能够测量物体的位置,其精度能够满足工业使用要求。     

A two‐station embossing process for rapid fabrication of surface microstructures on thermoplastic polymers

An embossing strategy involving a hot station and a cold station for sequentially heating and cooling the embossing tool was investigated to reduce cycle times in hot embossing polymer microstructures. Experimental studies showed that aluminum stamps with a thickness of 1.4 mm can be rapidly heated from room temperature to 200°C in 3 s using contact heating against a hot station at 250°C. Microchannels and microlenses were successfully embossed onto high‐density polyethylene and acrylonitrile–butadiene–styrene substrates using a heating time less than 3 s and a total cycle time around 10 s. The two‐station embossing process for the microlens was also numerically studied. The simulated filling behavior agreed with the experimental observation and the predicted thermal and deformation history of the polymer offered a good explanation on the experimentally observed process characteristics. POLYM. ENG. SCI., 47:530–539, 2007. © 2007 Society of Plastics Engineers.