开发井低渗透储层中长期产能预测

研究表明，某些低渗透储层具有启动压力梯度影响，即实际生产压差只有大于某个数值时，储层流体才能流动。针对此问题，从低速非达西渗流理论入手，给出了考虑启动压力影响的低速非达西储层的产能预测方法，并在F160-126等开发评价井上进行了应用，达到了准确评价低渗透非达西储层中长期产能、指导开发井生产的目的。     

科技期刊编辑专业化和学者化是保证期刊学术质量的关键

一般科技期刊刊载的论文内容都具有很强的专业性,这就要求科技期刊编辑必须具有丰富的专业知识和较高的学术水平才能胜任编辑工作.从编辑过程的选题组稿、论文初审、选择审稿专家和编辑加工四个方面对此进行了阐述,指出了提高科技期刊编辑的相关专业知识和学术水平的措施.     

基于遗传算法的水轮机最优工况参数计算

利用遗传算法计算水轮机的最优工况参数，给出遗传算法的具体实现步骤，并结合某电站的实际运行参数进行计算，结果表明，利用遗传算法计算水轮机的最优工况是可行的，而且寻优效率高，结果可靠。表2个。     

鞍钢1780mm热轧生产线"三电"工程施工概述

概述了鞍钢1780mm生产线技术改造工程中供电、传动及自动控制系统的构成、安装及调试技术要点,以及技术经济效果评述,可供同类工程施工参考.     

川东石炭系气藏排水采气工艺技术及其应用

四川盆地东部石炭系气藏是中国石油西南油气田公司的主力气藏之一，经过20多年的开发，出水气井增多、开发难度加大，必须进行排水采气才能维持正常生产。由于石炭系气藏大部分生产井存在井深、地层压力系数低、温度高、静液面深、复产后井口套压高的特点，常规排水采气工艺不能满足气藏的要求。针对这些难点，研究出深井高压气举、低压深井的优选管柱、深井高温泡排三项适合石炭系气藏的排水采气工艺，并在现场十多口井上进行了试验，增产效果显著。     

On the behavior of microstructures with multiple length scales

The current study aims to provide fundamental insight into the behavior of microstructures containing grain sizes that span multiple length scales. A commercial 5083 Al alloy was selected as the material of interest to facilitate comparison with recently published data. The materials studied here were prepared via the thermal consolidation of powders that were cryomilled for different times (i.e., 0, 2, 4, and 8 hours). Following consolidation, the resultant microstructure was characterized by an equiaxed grain morphology with a size distribution centered around 200∼300 nm. Dispersed among the 200- to 300-nm grains were coarse-grained regions or ligaments with a grain size ranging from 600 nm to 2 μm. The occurrence of coarse-grained regions is rationalized on the basis of recrystallization or subgrain coarsening, whereas the occurrence of equiaxed fine regions is proposed to be a result of continuous grain growth. Two types of microstructures were selected for study, containing coarse-grained volumes of approximately 28 pct and 43 pct that corresponded to an ultimate tensile strength (UTS) of 566 MPa and 535 MPa, and a fracture strain of 3.2 pct and 3.5 pct, respectively. The observed ductility and the relevant toughening mechanisms were discussed in light of the presence of multiple length scales.     

路43-P1水平井高密度钻井液难点技术的解决

路43-P1井是冀中坳陷饶阳凹陷留西油田路43断块施工难度较大的一口水平井。该井上部地层泥岩吸水膨胀造浆性强；下部地层局部存在异常高温，泥岩水敏性强，易吸水膨胀，造成地层坍塌。采用高密度钻井液钻井满足了井下要求，避免了井漏，减少了复杂情况的发生，缩短了建井周期；解决了深部定向、井温高、地层压力大、地层易垮塌的问题，顺利地完成了钻井目的。     

A Subcarriers Allocation Scheme for Cognitive Radio Systems Based on Multi-Carrier Modulation

Cognitive radio (CR) is a dynamic spectrum access technology as a solution to spectrum under-utilization problem in some licensed bands. Operating over an exceedingly wide spectrum, CR systems usually adopt multi-carrier modulation (MCM) to implement flexible channelization. Consequently, efficient channel allocation scheme becomes extremely important to an MCM based CR (MCM-CR) system. In this paper, a maximum likelihood detection model is developed to detect the presence and locations of licensed users (LUs) signals in the frequency domain. Performance of the detection model, including the optimal detection region, detection probability and false alarm probability, is analyzed. A one-order two-state Markovian chain model is proposed to predict channel status information. In particular, a novel subcarrier allocation scheme for MCM-CR systems is proposed, taking into account the confidence of channel estimation, quality of services (QoS) of rental users (RUs) and throughput. To validate the analytical results, simulations have been conducted to show effectiveness of the proposed scheme.     

Mechanical properties of iron processed by severe plastic deformation

In the present study, the mechanical properties of Fe processed via severe plastic deformation (equal-channel angular pressing (ECAP)) at room temperature were investigated for the first time. The grain size of annealed Fe, with an initial grain size of about 200 μm, was reduced drastically during ECAP. After eight passes, the grain size reaches 200 to 400 nm, as documented by means of transmission electron microscopy (TEM). The value of microhardness during pressing increases 3 times over that of the starting material after the first pass and increases slightly during subsequent pressing for higher-purity Fe. Examination of the value of microhardness after eight passes as a function of post-ECAP annealing temperature shows a transition from recovery to recrystallization, an observation that resembles the behavior reported for heavily deformed metals and alloys. The tensile and compression behaviors were examined. In tension, a drop in the engineering stress-engineering strain curve beyond maximum load was observed both in the annealed Fe and the ECAP Fe. This drop is related to the neck deformation. The fracture surface, examined by scanning electron microscopy (SEM), shows vein patterns, which is different from the dimples found on the fracture surface of annealed Fe. In compression, an initial strain-hardening region followed by a no-strain-hardening region was observed in the ECAP Fe. The yield strength in tension of the ECAP Fe was observed to be higher than that in compression. The strengthening mechanisms and softening behavior are discussed.     

长庆油田苏平1井固井技术研究与应用

苏平l井完井方式运用了技术套管一次上返、悬挂尾管和筛管技术。该井技术套管段井眼大、裸眼段长，加上大斜度、小间隙的尾管段．对水泥浆体系的性能要求较高。总结分析了长庆天然气水平井苏平l井的固井技术问题，介绍了苏平l井的井身结构与地层性质。通过研究．确定采用低失水GSJ水泥浆体系。该体系成功地应用在三次工程建井过程中，解决了长裸眼、大灰量、大斜度、尾管小间隙等固井技术问题。固井质量达到工程要求。