给定拓扑结构的网络的可靠性设计

本文首先讨论了网络链路堵概率的加权平均值，提出了网络分配的一般准则，并在考虑了网络链路生存链路概率的因素后，提出了更一般的网络链路堵塞概率的加权平均值，以此为基础，分别讨论了网络在给定点的费用条件下，使得网络可靠性最大的网络设计问题，以及在给定网络可靠性指标的前提下，使得网络费用最小的网络设计问题。     

基于ATM的网络互连方式

ＡＴＭ技术能否在数据通信网中广泛采用取决于其是否能高效地支持现有业务，其中主要为非连接业务。本文介绍了几种基于ＡＴＭ 的非连接业务支持方式和协议体系结构，对其进行了评述并对ＩＰ分组到ＡＴＭ信元的封装效率进行了分析。     

New balance ground relay for parallel four-circuit transmission lines

A 66-kV network generally is grounded through a neutral grounding resistor. In this network a single-phase ground-fault current is limited to as small as 100 to 400 A. There are parallel four-circuit transmission lines mounted on the same tower in the 66-kV network. In such transmission lines, the load and the fault currents could induce circulating current that flows through the lines. Since the circulating current has zero-phase-sequence and negative-phase-sequence components, it could cause unwanted operation of a balance ground relay using zero-phase-sequence current. However, it is difficult to compensate for the circulating current by the conventional vector compensation scheme. This paper presents a new balance ground relay to deal with the circulating current. In the relay from the ground-fault inception until first tripping, the difference current Δ3I_2d of negative-phase-sequence current 3I_2d of the differential current between two protected lines is used as an input current. The Δ3I_2d is the difference current of 3I_2d between, before and during faults. After the first tripping, the difference current of positive-phase-sequence load current and zero-phase-sequence current of the forementioned differential current are used as an input current. Consequently, a higher sensitivity of the ground-fault protection for these lines has been achieved. The correct operation of the new balance ground relay was confirmed when a single-phase-ground-fault occurred in the parallel four-circuit transmission lines, to which the relay is applied.     

航空油品高频/高压电脱水微观机理

设计并建立了一套高压电物理化学显微分析装置，为研究高压电物理化学领域的微观机理提供了一种新的技术途径。采用该技术，研究了胜利稠油经6％加氢裂解柴油稀释的原料油的高频／高压电脱水的微观机理。该原料的脱水率达96．7％，高于传统的电脱水方法。     

国家战略发展新能源股价长期走牛可期待

严峻的能源短缺、居高不下的原油价格、日益严重的环境问题已经成为制约中国经济、社会发展的瓶颈。改变现有的以化石能源为主的能源结构,     

基于图像的虚拟环境建模技术

综述了基于图像的虚拟现实环境的建模技术，并给出了各种模型表示的理论依据和建模过程的定义。把环境表示分为四类：全景图，光场数据库，深度图像和多投影中心图。全景图的生成包括基于图像相关性和基于图像整合变换的算法。光场数据库的分类主要依据全光函数。同时论述了在各种表示下的采样和建模技术。最后讨论了当前建模技术研究的热点及所需要解决的问题。     

离子液体用于燃料油深度脱硫的研究进展

首先介绍了加氢催化脱硫和其他脱硫技术的特点,综述了近年来国内外利用离子液体在萃取脱硫、萃取脱硫与氧化脱硫耦合、萃取脱硫与生物脱硫耦合等方面的研究。认为离子液体萃取脱硫具有操作简便、可循环使用、无需氢气、环境友好、能深度脱硫等特点,是一项具有广阔发展前景的技术。若要实现该技术的工业化应用,还需进一步加强离子液体在合成工艺、脱硫选择性及回收再生等方面的研究。     

Application of Code Approach for Emergency Evacuation in a Rail Station

This paper presents an emergency evacuation analysis during a mid-platform train fire in an underground rail station. A time-based evacuation scenario is developed taking into account the stairway inaccessibility due to smoke blockage. The calculation approach in NFPA 130 is then applied to a parametric study of this time-based scenario and its reliability is examined using a micro-simulation model. Both methods give consistent predictions of the exiting times. The results demonstrate that with the division of the station into two zones, the exiting time could not meet the code requirements, whereas it does meet the required exiting time without the division. Such division is due to smoke blockage and creates an uneven ratio of the occupant load to the available exiting capacity. This shows that appropriate consideration of the fire and smoke effects is important for station egress evaluation. Other issues such as the fire growth rate and the pre-evacuation time are also discussed.     

OFDM-MIMO系统及其频率同步分析

多媒体业务对无线通信的带宽与品质提出了更高的要求，OFDM和MIMO由于满足了这一需求被越来越多的无线通信标准采用所为底层的调制和传输技术。频率同步问题是OFDM—MIMO物理层设计中正确解调的前提和基础，本文介绍了OFDM—MIMO的原理、特点和频率同步问题的研究现状。     

Detection of failure sites by focused ion beam and nano-probing in the interconnect of three-dimensional stacked circuit structures

Focused ion beam (FIB) and nano-probing were applied for failure analysis of three-dimensional stacked circuits with copper through-silicon-vias between the stacked chips. The failure analysis was done after high temperature storage and thermal cycling tests. Passive voltage contrast in FIB allowed to pinpoint the open sites. FIB cross-sections showed the presence of opens at the bottom of the copper vias. The failure cause was suspected to be an interlayer particle, which was confirmed by optical profilometry. Nano-probing was used on another sample to pinpoint the failure location through the measurement of the local resistance within the daisy chains. The failure was traced out to be related with surface contamination.