Effect of evaporation time on the pervaporation characteristics through homogeneous aromatic polyamide membranes. II. Pervaporation performances for ethanol/water mixture

Pervaporation of ethanol/water mixtures through symmetric dense aromatic polyamide membranes was investigated. The membrane structure was controlled by varying the solvent evaporation time before gelation. The membranes were water-selective and the selectivity increased with an increase in the solvent evaporation time. On the other hand, the water flux as well as the ethanol flux decreased with an increase in the evaporation time. These results were consistent with the morphology change of the membrane which takes place with solvent evaporation: the decrease in the channel size. The effects of the downstream pressure on the pervaporation performances were also studied for membranes with different solvent evaporation times. the ethanol concentration in the permeate side increased with an increase in the downstream pressure to certain point, showed a maximum there, then decreased thereafter. The water flux decreased with an increase in the downstream pressure for all membranes studied; the dependence was expressed by a parabolic curve in the lower pressure range. The ethanol flux also decreased with an increase in the downstream pressure for the membrane with shorter evaporation time, while this flux was slightly affected by the downstream pressure for the membrane with longer evaporation time. © 1996 John Wiley & Sons, Inc.     

Burning Rate Augmentation of BAMO Based Propellants

Thermal decomposition and the burning properties of BAMO based propellants with HMX or AN/HMX have been investigated. The heat generated by the azide binder decomposition initiated and accelerated the thermal decomposition of HMX and AN. Ammonium perchlorate (AP) and lead stearate with carbon black significantly altered the mechanisms of the thermal decomposition and the burning properties of the HMX based propellants. AP showed an increase in burning rate with a slight decrease in burning rate pressure exponent. The lead catalyst yielded high value of the burning rate with the lowest pressure exponent. The ammonium dichromate also influenced the mechanisms of the thermal decomposition and the burning properties of the AN/HMX samples. The combination of ammonium dichromate and copper chromite was the most effective on the burning rate augmentation of AN/HMX based propellants. AN sublimed and evaporated from the condensed phase and mainly reacted exothermically in the gas phase HMX and AN/HMX based propellants showed smokeless burning characteristics in the small rocket motor combustion tests.     

Preparation and characterization of polyvinylidene fluoride hollow fiber membranes for ultrafiltration

Polyvinylidene fluoride (PVDF) hollow fiber membranes were prepared using the solvent spinning method. N,N-dimethylacetamide was the solvent and ethylene glycol was employed as non-solvent additive. The effect of the concentration of ethylene glycol in the PVDF spinning solution as well as the effect of ethanol either in the internal or the external coagulant on the morphology of the hollow fibers was investigated. The prepared membranes were characterized in terms of the liquid entry pressure of water measurements, the gas permeation tests, the scanning electron microscopy, the atomic force microscopy, and the solute transport experiments. Ultrafiltration experiments were conducted using polyethylene glycol and polyethylene oxides of different molecular weights cut-off as solutes. A comparative analysis was made between the membrane characteristic parameters obtained from the different characterization techniques.     

Kinetics and reaction scheme of coal liquefaction over molten tin catalyst

Rates of formation of gases, oils, asphaltenes and preasphaltenes during non-solvent liquefaction of coal over molten tin catalyst have been measured. A probable reaction scheme and the rate constants for the pathways comprising the scheme have been presented. The results show that the catalyst greatly accelerates the conversion of preasphaltenes to asphaltenes. It also accelerates two other reactions, i.e., coal to preasphaltenes and coal to asphaltenes. By contrast, the catalyst does little to promote gasification and formation of oils.     

In vitro evolution of proteins

Consecutive rounds of diversification and selection of the fittest is believed to be the main driving force for the evolution of life. For the evolution of life to proceed, all living cells are surrounded by a lipid bilayer that separates their own genes from the external environment and from those of other organisms. In this way, the genetic information of an individual is replicated on the basis of their phenotype; thus the enrichment of the fittest will occur. Hence, evolution is based on linkage between genotype and phenotype owing to the surrounding of the genetic material with a barrier. The linkage between genotype and phenotype is also known to be essential for the directed evolution of proteins. Indeed, systems for molecular evolution, including phage display, ribosome display, and in vitro compartmentalization, all satisfy this requirement in different ways. These systems have been shown to be powerful tools for high-throughput screening for the functions of proteins, screening as many as <10(12) molecules in 1 d. These selection systems in combination with various gene libraries yield proteins with improved or altered biophysical properties, and may even allow the generation of proteins with novel functions.     

Effect of the t–m transformation morphology and stress distribution around the crack path on the measured toughness of zirconia ceramics: A case study on Ce-TZP/alumina nanocomposite

The t–m transformation zone and related residual stress fields around two types of crack used for toughness measurements, i.e. SEVNB (arrested crack induced by a V-notch) and IF methods (indentation crack induced by a Vickers impression), are reported for a Ce-TZP/Al₂O₃ nanocomposite, in comparison with 3Y-TZP. The fact that Ce-TZP/Al₂O₃ exhibits significant high toughness value on occasions when evaluated by the IF method was determined to be clearly linked to the presence of wide ranged three-dimensional transformation configuration and resulting substantial compressive residual stress fields. In contrast, for 3Y-TZP, transformation behaviors around the two types of crack were quite similar, which proves that 3Y-TZP shows near toughness values for both SEVNB and IF methods.     

Fracture toughness evaluation of adjacent flow weld line in polystyrene by the SENB method

Fracture toughness of adjacent flow weld lines, defined as weld lines that occur when two flow fronts meet and continue to flow together in the same direction (meld line or hot weld line), was evaluated by the single‐edge notched‐bend (SENB) method using three differently‐shaped obstructive pins. Although the fracture toughness varied depending upon the shapes of the pin, the values could be standardized as the distance from the meeting point of the two flow fronts flowing around the pin. The fracture toughness decreased drastically from the meeting point along the weld line and then slightly increased. These characteristic features could be explained by flow‐induced molecular orientation at the weld line interface. The molecules around the meeting point that were initially oriented parallel to the weld line due to fountain flow were able to relax, and then entanglement across the weld line interface developed because the flow stopped in the middle of the filling process, resulting in high fracture toughness. In contrast, the material at the downstream side of the weld line continued flowing during the filling process, being stretched along the flow direction. So, the molecular orientation at this area could not relax. In addition, the V‐notch shape, i.e., the depth and length at the surface of the weld line, which also varied depending on the shape of the obstacles, was considered to be identical when the meeting point was allowed to be a datum point. Thus, the meeting point was found to be a significant factor when the properties of weld lines are investigated. POLYM. ENG. SCI., 45:1059–1066, 2005. © 2005 Society of Plastics Engineers     

Removal of hydrogen sulfide from methane using commercial polyphenylene oxide and Cardo-type polyimide hollow fiber membranes

The performance of commercially available poly (2,6-dimethyl-1,4-phenylene oxide) (PPO) and Cardotype polyimide (PI) hollow fiber membranes was investigated in removing hydrogen sulfide from methane in a series of bench-scale experiments. It was observed that in the concentration range of hydrogen sulfide in methane from 101 to 401 ppm, the methane permeability decreased in the presence of hydrogen sulfide for Cardo-type polyimide hollow fiber membranes, whereas the PPO membrane performance was not affected. The separation coefficients of hydrogen sulfide/methane were 6 and 4 for PI and PPO membranes, respectively. Effects of temperature on the performance of PI and PPO membranes were investigated. It was observed that the permeabilities of both components of the mixture increased by increasing temperature, whereas the selectivities remained constant.     

In vitro selection of proteins that undergo covalent labeling with small molecules by thiol-disulfide exchange by using ribosome display

There is a great deal of interest in proteins that can bind covalently to target molecules, as they allow unambiguous experiments by tight binding to molecules of interest. Here, we report the generation of proteins that undergo covalent labeling with small molecules through in vitro selection by using ribosome display. Selection was performed from a mutant library of the WW domain with a biotinylated peptide as its binding target, in which the biotin and the peptide are connected by a disulfide bond. After five rounds of selection, we identified mutants carrying a particular cysteine mutation. The binding target reacted specifically with the selected mutant, even in the presence of other proteins, and resulted in the generation of biotin- or peptide-labeled WW domains by thiol-disulfide exchange. When the mutant was fused to a protein of interest, the fusion protein was also labeled with biotin. Thus, the characteristics of the selected mutant should be suitable as a tag sequence that can be covalently labeled with small synthetic molecules. These results indicate that the rapid and efficient generation of such proteins is possible by ribosome display.