纳米α-FeOOH颗粒的形态和结构

以硫酸法钛白的副产物绿矾为原料，采用滴加法制备纳米铁黄（α－FeOOH）颗粒。研究了反应体系的pH值、反应温度、通氧速率、搅拌速率和添加剂等对铁黄颗粒形态结构的影响，采用XRD、TEM等分析手段对颗粒进行表征。结果表明，调节体系pH值能控制铁黄晶型结构和色相；改变通氧速率、搅拌速率、添加剂种类以及反应温度等可以调节纳米α－FeOOH的大小和分散性。     

Containerless solidification of highly undercooled mullite melts: Crystal growth behavior and microstructure formation

A mullite (3Al₂O₃·2SiO₂) sample has been levitated and undercooled in an aero-acoustic levitator, so as to investigate the solidification behavior in a containerless condition. Crystal-growth velocities are measured as a function of melt undercoolings, which increase slowly with melt undercoolings up to 380 K and then increase quickly when undercoolings exceed 400 K. In order to elucidate the crystal growth and solidification behavior, the relationship of melt viscosities as a function of melt undercoolings is established on the basis of the fact that molten mullite melts are fragile, from which the atomic diffusivity is calculated via the Einstein-Stokes equation. The interface kinetics is analyzed when considering atomic diffusivities. The crystal-growth velocity vs melt undercooling is calculated based on the classical rate theory. Interestingly, two different microstructures are observed; one exhibits a straight, faceted rod without any branching with melt undercoolings up to 400 K, and the other is a feathery faceted dendrite when undercoolings exceed 400 K. The formation of these morphologies is discussed, taking into account the contributions of constitutional and kinetic undercoolings at different bulk undercoolings.     

Interfacial segregation of Ti in the brazing of diamond grits onto a steel substrate using a Cu-Sn-Ti brazing alloy

Diamond grits were brazed onto a steel substrate using a prealloyed Cu-10Sn-15Ti (wt pct) brazing alloy at 925 °C and 1050 °C. Due to the relatively high concentration of Ti in the brazing alloy, the braze matrix exhibited a composite structure, composed of β-(Cu,Sn), a Cu-based solid solution, and various intermetallic compounds with different morphologies. The reaction of Ti with diamond yielded a continuous TiC layer on the surfaces of the diamond grits. On top of the TiC growth front, an intermetallic compound, composed of Sn and Ti, nucleated and grew into a randomly interwoven fine lacey structure. An interfacial structure developed as the interwoven fine lacey phase was semicoherently bonded to the TiC layer, with the Cu-based braze matrix filling its interstices. The thickness of such a composite layer was increased linearly with the square root of isothermal holding time at 925 °C, complying with the law of a diffusion-controlled process. However, at 1050 °C, the segregation behavior of Ti and Sn to the interfaces between the TiC layer and the braze matrix diminished, due to the increased solubility of Ti in the Cu-based liquid phase. The enhanced dissolution of Ti in the Cu-based liquid phase at 1050 °C also caused the precipitation of rod-like CuTi with an average diameter of about 0.2 μm during cooling. SnTi₃ was the predominant intermetallic compound and existed in three different forms in the braze matrix. It existed as interconnected grains of large size which either floated to the surface of the braze matrix or grew into faceted grains. It also exhibited a nail-like structure with a mean diameter of about 1 μm for the rod section and a lamellar structure arising from a eutectic reaction during cooling.     

全IP移动通信网网络层移动性管理

首先介绍了全IP移动通信网网络层移动性管理的概念、框架和最经典的移动IP（Mobile IP）协议，然后讨论了基于Mobile IP的四种主要扩展方案：蜂窝IP、切换敏感无线接入Internet结构（HAWAII)、电信增强移动IP（TeleMIP）和边缘移动性体系结构（EMA）方案，最后结合第三代移动通信发展的状况得出了一些结论。     

有耗传输线的TLM模型法

本文从传输线理论出发，介绍了一种解决传输线问题的新方法－－TLM法。     

试论会计电算化系统的内部控制

阐述了会计电算化系统产生和发展对内产控制的影响，以及内部控制的实施方法。     

On the interaction impedance of the coupled cavity structure

The formula and program for calculating the total and negative first harmonic interaction impedance from the data of “large perturbation measurement” are given. This program is a part of the programs for CCTWT design.     

3-D boundary element method for cracks in a plate

New fundamental solutions which automatically satisfy boundary conditions at the interfaces of an elastic plate perfectly bonded to two elastic halfspaces are implemented in a 3-D boundary element method (BEM) for crack problems. The BEM features a new integration scheme for highly singular kernels. The capability is achieved through a part analytic and part numerical integration procedure, such that the analytic part of the integration is similar for all slip/opening variations, ‘Part-through’ elliptic cracks in an elastic plate with traction-free surfaces are analysed and the stress intensity factor (SIF) values along the crack front are found to compare favourably with widely accepted numerically obtained SIF results by Raju and Newman.¹     

ZnGa2O4纳米晶的制备和结构表征

采用喷射共沉淀法制备了ZnGa2O4 纳米晶，XRD、SEM和TEM结构分析结果表明，喷射共沉淀法制备的ZnGa2O4的纳米晶颗粒细小均匀，形状完整，与化学共沉淀法相比，粒子尺寸明显减小，小于10nm，同时ZnO杂相峰消失，分析了喷射共沉淀法的机理，并对实验结果进行了解释。