2-D dopant profiling in VLSI devices using dopant-selectiveetching: an atomic force microscopy study

We report a detailed mapping of a 2-D dopant profile on a fully processed industrial sample with large dynamic range and high spatial resolution by utilizing a dopant-selective etching process and Atomic Force Microscopy. The experimental results show excellent agreement with those obtained from SRP and SIMS as corroborative methods. We also discuss the most critical factors which influence the applicability, reproducibility, and reliability of this method     

The effects of plasma etching induced gate oxide degradation onMOSFET's 1/f noise

The effects of the plasma etching process induced gate oxide damages on device's low frequency noise behavior are investigated on MOSFET's fabricated with different field plate perimeter to gate area ratio antennas. Abnormal 1/f noise spectrum with a shoulder centered in the frequency range of 100 and to 1 kHz was frequently observed in small geometry devices, and it is attributable to a nonuniform distribution of oxide traps induced by plasma etching process     

COIL中BHP浓度对发生O_2(~1△)的影响

本文实验研究了BHP的浓度对产生O2（1△）的影响。实验结果表明：当BHP浓度大于3.5M时，Cl2利用率以及O2（1△）的产率将不依赖于BHP浓度的变化而变化，同时，实验结果表明，使用低浓度的BHP对COIL的操作是可行的。     

Air Filtration and Radon Decay Product Mitigation

Air cleaning as a means of mitigating the risks arising from exposure to indoor radon progeny has been evaluated in a single-family house in the north eastem US. using an automated, semi-continuous activity-weighted size distribution measurement system. The measurements included radon concentration, condensation nuclei count, and activity-weighted size distribution of radon decay products. Measurements were made in the house with and without an operating air filtration system and with various particle sources common to normal indoor activities operating. Aerosols were generated by running water in a shower, candle burning, cigarette smoking, vacuuming, opening doors, and cooking. Using a room model, the changes in attachment rates, average attachment diameters, and deposition rates of the unattached fraction with and without the air cleaning system were calculated. In the presence of active aerosol sources, the air filtration unit typically reduced the concentration of particles within the hour following the end of particle generation. After candle burning, cigarette smoking, and vacuuming in the bedroom, the reductions of PAEC by air filtration are about 60% with the air filtration system operating in the bedroom. During cooking in the kitchen, the reductions of PAEC in the bedroom with the air filtration system were about 40%. However, for all cases the dose reductions were smaller than the particle and PAEC reductions. For those particles that were generated within the bedroom, there was a 20% to 50% reduction in dose. In the case of cooking where the door was open and particles infiltrated from the rest of the house, the dose reduction was only 5% on average and appears to be insignificant. Thus, the dose reductions were h e r than the reductions in activity concentration, but there were no cases where the estimated dose actually increased.     

Reply to comments on “Error rate performance of theprojection code”

The authors reply to the comments by Koppelaar and Tolhuizen (see ibid. vol.46, no.9, p.573, 1998). They state that the optimum choice of the slopes used to perform the encoding process in a projection code always results in maximizing the minimum Hamming distance so that d=2 ^r     

Inter- and intra-molecular ionic interactions of polyampholyte: Carboxymethyl-2-diethylaminoethylcellulose

Carboxymethyl-2-diethylaminoethylcellulose (CM-DEAE cellulose) was prepared by etherification of carboxymethylcellulose with diethylaminoethyl chloride in a NaOH solution. The behaviour of CM-DEAE cellulose in aqueous solution was studied by viscosity and GPC measurements. The degree of substitution (DS) and existing states of DEAE substituents were examined by the use of proton NMR, and those of the CM substituents were observed with FT-IR. The results reveal that the reduced viscosity and apparent molecular size of CM-DEAE cellulose vary with the concentration of sodium chloride and changes in pH and DS. These phenomena can be explained in terms of inter- and intra-molecular ionic interactions.     

Crystallization behaviour of Ni-Co-base metallic glasses by isochronal and isothermal annealing

The crystallization behaviour of three amorphous alloys, Co₅₀Ni₂₅Si₁₅B₁₀, Ni₅₀Co₂₅Si₁₅B₁₀ and Ni₅₀Co₂₅P₁₅B₁₀, was studied by means of differential thermal analysis in conjunction with scanning transmission electron microscopy. Isochronal annealing showed a strong dependence of crystallization on scan rate over the range of 1.99 to 20.70 K min^–1. At high Co/Ni ratios, a sequential two-stage crystallization process involving primary MS-I phase followed by MS-II phase precipitation was observed. At low Co/Ni ratios MS-I and MS-II crystallization were concurrent and inseparable. Replacement of the metalloid Si with P as the glass-former dramatically reduced the activation energy for crystallization as well as the crystallization temperature. A mechanistic understanding of these findings was pursued in light of TEM/STEM microanalysis     

感光乳剂熔化三要素对熔化供料的影响

本文讨论了温度、搅拌和时间三要素对感光乳剂和工艺过程的影响，指出了上述影响的后果和严格过程控制的重要性，提出克服影响的措施。