Onset of buoyancy-driven convection in melting from below

When a horizontal homogeneous solid is melted from below, convection can be induced in a thermally unstable melt layer. In this study the onset of buoyancy-driven convection during time-dependent melting is investigated by using similarly transformed disturbance equations. The critical Rayleigh numbers based on the melt-layer thickness are found numerically for various conditions. For small superheats, the present predictions approach the well known results of classical Rayleigh-Bénard problems, that is, critical Rayleigh numbers are located between 1,296 and 1,708, regardless of the Prandtl number. However, for high superheats the critical Rayleigh number increases with an increase in phase change rate but with decrease in Prandtl number.     

多孔薄膜荫罩热变形的有限元仿真设计

荫罩的热变形使电子束产生着屏偏移 ,进而导致了色纯变坏。本文采用大型软件ANSYS对 1 5英寸荫罩进行了热变形的有限元仿真 ,从而得到了电子束的着屏偏移。建立了包括阴极射线管 (CRT)里所有部件的完整的有限元模型。荫罩被建为无孔连续薄壳的模型 ,对它的表面导热系数和表面弹性模量作了等效的计算。考虑了弹簧片的预应力以及弹簧片和销钉的连接。这样可使我们的分析模型更接近真实情况。本文给出了 50 0、1 0 0 0、1 0 0 0 0s时的热变形和电子束着屏偏移。分析表明 :电子束着屏偏移的最大值发生在 50 0s左右。利用这种分析方法及研究结果可指导新型荫罩的设计和研制。     

基体温度对磁控溅射沉积ZAO薄膜性能的影响

利用中频交流磁控溅射方法 ,采用氧化锌铝陶瓷靶材 [w(ZnO) =98%、w(Al2 O3 ) =2 % ]制备了ZAO(ZnO∶Al)薄膜 ,观察了基体温度对ZAO薄膜的晶体结构、电学和光学性能的影响 ,采用X射线衍射仪对薄膜的结构进行了分析 ,采用光学分度计和电阻测试仪测量了薄膜的光学、电学特性 ,采用霍尔测试仪测量了薄膜的载流子浓度和霍尔迁移率。结果表明 :沉积薄膜时的基体温度对薄膜的结构、结晶状况、可见光透射率以及导电性有较大的影响。当基体温度为 2 5 0℃ ,Ar分压为 0 8Pa时 ,薄膜的最低电阻率为 4 6× 10 -4Ω·cm ,方块电阻为 35Ω时 ,可见光 (λ =5 5 0nm)透射率高达 92 0 %。     

实验室条件下聚能射孔损害带研究

在实验室条件下对贝雷砂岩进行射孔试验,并分别对射孔后的靶体进行酸化、压裂工艺处理,利用核磁共振和工业X-CT技术分别对未射孔的靶体、射孔后的靶体、射孔后酸化的靶体、射孔后压裂的靶体进行测试.定量分析了射孔对砂岩靶体的损害及酸化、压裂对射孔损害的解除作用.     

Ring‐opening polymerization of D,L‐lactide by rare earth 2,6‐dimethylaryloxide

Ring‐opening polymerization of D,L ‐lactide (LA) has been successfully carried out by using rare earth 2,6‐dimethylaryloxide (Ln(ODMP)₃) as single component catalyst or initiator for the first time. The effects of different rare earth elements, solvents, monomers and catalyst concentration as well as polymerization temperature and time on the polymerization were investigated. The results show that La(ODMP)₃ exhibits higher activity to prepare poly(D,L ‐lactide) (PLA) with a viscosity molecular weight of 4.5 × 10⁴ g mol^?1 and the conversion of 97 % at 100 °C in 45 min. The catalytic activity of Ln(ODMP)₃ has following sequence: La > Nd > Sm > Gd > Er > Y. A kinetic study has indicated that the polymerization is first order with respect to both monomer and catalyst concentration. The apparent activation energy of the polymerization of LA with La(ODMP)₃ is 69.6 kJ mol^?1. The analyses of polymer ends indicate that the LA polymerization proceeds according to ‘coordination–insertion’ mechanism with selective cleavage of the acyl–oxygen bond of the monomer. Copyright © 2004 Society of Chemical Industry     

A Nonvolatile Organic Memory Device Using ITO Surfaces Modified by Ag‐Nanodots

We report on a single‐layer organic memory device made of poly(N‐vinylcarbazole) embedded between an Al electrode and ITO modified with Ag nanodots (Ag‐NDs). Devices exhibit high ON/OFF switching ratios of 10⁴. This level of performance could be achieved by modifying the ITO electrodes with some Ag‐NDs that act as trapping sites, reducing the current in the OFF state. Temperature dependence of the electrical characteristics suggest that the current of the low‐resistance state can be attributed to Schottky charge tunnelling through low‐resistance pathways of Al particles in the polymer layer and that the high‐resistance state can be controlled by charge trapping by the Al particles and Ag‐NDs.     

Complementary effects of solid lubricants in the automotive brake lining

An experimental investigation was carried out to examine the tribological behavior of NAO (non-asbestos organic) type brake linings containing different volume ratios of graphite and antimony trisulfide (Sb₂S₃). A scale dynamometer was used for friction tests and particular emphases were given to the effect of applied pressure, sliding speed, and temperature on the coefficient of friction according to the relative amounts of the two solid lubricants. Results showed that the brake linings with both solid lubricants exhibited better friction stability and less speed sensitivity than the friction materials containing a single solid lubricant. In particular, the brake lining containing higher concentrations of graphite showed better fade resistance than others during high-temperature friction test.     

储层压力与天然气分布关系——以鄂北塔巴庙地区上古生界储层为例

通过分析塔巴庙地区储层压力的分布特征，建立了研究区泥岩压实曲线，并对影响和控制该区储层压力的主要因素和机理进行了探讨，对“欠压实”剩余压力、生气增压、抬升引起的降压进行了定量计算。分析结果表明，晚三叠-早白垩世末“欠压实”作用和晚侏罗-早白垩世末烃源岩大量生烃作用使塔巴庙地区上古生界形成异常高压；晚白垩系构造抬升降压，使得现今储层为正常-低异常压力。同时证实了“欠压实”对天然气有压力封盖作用，天然气都分布在最大“欠压实”幅度以下的储层当中。烃源岩生气高峰为晚侏罗-早白垩世末，但天然气大规模运移是在晚白垩世，方向以沿过剩压力梯度降低较快的方向（太原-山西组至下石盒子组）垂向运移，通道主要为裂缝，运移的动力主要为异常高压。由于储层致密，聚集成藏能量有限，造成天然气充注不足、气水分异不好、含气饱和度低。     

甘油三乙酸酯超临界酯交换反应及其动力学研究

研究了在超临界条件下甘油三乙酸酯与甲醇或乙醇的酯交换反应,分别考察了超临界状态下醇油摩尔比和温度对反应的影响。实验结果表明,甲醇或乙醇与甘油三乙酸酯的摩尔比为14、反应温度为350℃、反应时间为20m in时,乙酸甲酯或乙酸乙酯的收率分别达100%和60%。对超临界状态下动力学的研究结果表明,甘油三乙酸酯与甲醇或乙醇的酯交换反应为拟一级反应,在相同的反应条件下,采用甲醇时酯交换反应速率比用乙醇时快,相应的甘油三乙酸酯的转化率也高;甘油三乙酸酯在超临界甲醇或乙醇中酯交换反应的表观活化能分别为58.7 kJ/mol和75.1 kJ/mol,甘油三乙酸酯与甲醇酯交换反应的活化能低于与乙醇酯交换反应的活化能,表明碳链短的醇更易进行酯交换反应。     

数控超声加工的初步工艺试验

介绍在经过数控化改造的两坐标超声加工机床上所进行数控超声加工的初步工艺试验,并讨论试验结果。