Braking Behavior of C/SiC Composites Prepared by Chemical Vapor Infiltration

Carbon fiber-reinforced silicon carbide matrix composites have the potential to overcome the shortcoming of the currently used carbon/carbon friction materials in aircraft brakes. In this article, the carbon/silicon carbide (C/SiC) composites were prepared by chemical vapor infiltration method, and the brake disks with different densities and component content were finally obtained. The friction coefficient and friction stability can be significantly improved by increasing both material density and carbon content. When the density of C/SiC composite is 2.3 g/cm³, the coefficient of friction measured is 0.23, the coefficient of friction stability remains about 0.43, the liner wear rate is less than 9.3 μm/cycle, and the weight wear rate is less than 9.1 μm/cycle. The rapid increase of friction coefficient approaching the end of braking is mainly related to the increasing of surface temperature in a short time and the enhanced adhesion and abrasion of contact conjunctions and asperities. The C/SiC composites exhibited a good stability of braking against fading versus the braking number and surface temperature. The surfaces of C/SiC brake disks were covered with wear debris including the fragment of carbon fibers after the braking tests. The wear on the surfaces is significantly determined by cyclic mechanical and thermal stresses, which result in the micro-cracks in the SiC matrix, the thin flakes of the surface materials as well as the grooves.     

Grafting of alkoxyamine end-capped (co)polymers onto multi-walled carbon nanotubes

Multi-walled carbon nanotubes (MWNTs) have been successfully modified by polystyrene, poly(?-caprolactone), and their block copolymers by addition reaction of the alkoxyamine-terminated precursors. Polymer-modified MWNTs are easily dispersed in good solvents for the grafted polymer, such as toluene and THF. This observation has been confirmed by TEM analysis. The grafting ratio of polystyrene chains at the surface of MWNTs depends on the polymer molecular weight.     

臭氧氧化法除地表水有机物试验研究

本文阐述臭氧化法除地表水有机物的重要意义，实验结果表明：臭氧氧化有机物的总氧化速率受活化控制，影响氧化率的最高显著因素是温度，其次是ｐＨ，接触时间等，臭氧很容易氧化腐植酸，在３０℃，ｐＨ９．０～１０．０，７ｍｉｎ内，ＣＯＤ去除率可达６０％以上，对邯郸热电厂生产处理也取得良好效果，３５℃，ｐＨ７．４～７．６，１０ｍｉｎ内，ＣＯＤ去除率可达６７％，可望将臭氧化水处理工艺应用于电厂水处理。     

High-performance dispersant of coal–water slurry synthesized from wheat straw alkali lignin

Environmental concerns have stimulated interest in utilizing plant-derived materials in various industrial fields. The main objective of the present study was to synthesize a new type of high-performance lignin series dispersant of coal–water slurry (CWS) from wheat straw alkali lignin (WAL), and determine the affecting factors in the reaction and the application performance for CWS preparation. The experimental results showed that the inherent viscosity and the sulfonic group content of the modified wheat straw alkali lignin (MSL) are the key factors affecting its dispersing effect for CWS. In the reaction, the reactant mass concentration and the sulfonating agent amount were changed to obtain the MSL with different inherent viscosities and sulfonic group contents, and the MSL with intermediate inherent viscosity (6.0 ml/g) and higher sulfonic group content (1.80 mmol g^− 1) was found to have excellent dispersing effect for CWS. The MSL obtained from optimized process was used as dispersant for CWS preparation, the studies of the properties of CWS showed that MSL has similar dispersing effect with naphtalenesulfonate–formaldehyde condensate, and far better dispersing effect than lignosulphonate. Recently this kind of new dispersant has been applied in several power plants in China.     

氯化聚乙烯接枝氯乙烯聚合速率及传热

本文用气相色谱技术研究氯化聚乙烯(CPE)-接枝(g)-氯乙烯(VC)聚合动力学,对不同引发剂体系分析热负荷分布,并对7 m~3聚合釜传热面进行校核。     

一种适用于物联网节点的高效轻量级嵌入式系统设计

物联网技术成为当前一个比较热门的研究主题,但适用于物联网传感器的嵌入式操作系统在国内未被广泛提及。本文针对嵌入式多任务程序设计所面对的问题,结合物联网传感器资源受限、低功耗等特点,探讨该类程序的一般设计方法,提出了一种基于事件驱动抢占式系统的基本实现方法,并使之顺利应用于基于MSP430物联网传感器采集节点的系统中。     

Metastable Phase Selection and Partitioning for Zr(1−x)AlxO(2−x/2) Materials Synthesized with Liquid Precursors

Aqueous solutions of zirconium acetate and aluminum nitrate were spray pyrolyzed at 250°C and upquenched to different temperatures to yield metastable solid solutions of composition Zr_{(1− x )}Al_xO_{(2− x /2)}. An amorphous oxide forms first during pyrolysis which subsequently crystallizes as a single phase for x ≤ 0.57 (≤40 mol% Al₂O₃). The crystallization temperature increased with Al₂O₃ content. Electron diffraction, supported by Raman spectroscopy, indicates that the initial phase is tetragonal. At higher temperatures, the initial solid solation partitions to other metastable phases, viz., t -ZrO₂+γ-Al₂O₃, prior to achieving their equilibrium phase assemblage, m -ZrO₂+α-Al₂O₃. Partitioning yields a nanocomposite microstructure with grain sizes of 20–100 nm, compared to the 3 to 5 nm in the initial, single phase. Compositions containing 45 to 50 mol% Al₂O₃ concurrently crystallize and partition. The structure selected during crystallization and the partitioning phenomena are discussed in terms of diffusional constraints during crystallization, which are conceptually similar to those operating during rapid solidification.     

Electrical behavior of carbon black-filled polymer composites: Effect of interaction between filler and matrix

The effect of interaction between carbon black and polymer on electrical behavior was studied using the ESR method. The polymer matrices used were HDPE, LDPE, and ethylene/vinyl acetate (EVA). Two kinds of carbon blacks (CB), high structure CSF-III and low structure FEF, were used as a conductive filler. Compared to that of the HDPE/FEF compound, the positive temperature coefficient (PTC) intensity is lower and electrical reproducibility is worse for the HDPE/CSF-III compound; however, it can be improved significantly by radiation cross-linking. On the other hand, the cross-linking has no practical effect on the PTC intensity of the LDPE/CSF-III compound while it can be achieved by mixing the compound for a longer time. The great PTC intensity was obtained in the HDPE/EVA/CSF-III compound, and it is greater than that of HDPE/CSF-III or EVA/CSF-III. We explain these results using the concept of interaction between the filler and matrix. The absorption of the polymer on the carbon black surface may be physical or chemical; the latter is caused by the free-radical reaction between the polymer and carbon black, and it can occur during the radiation or preparation process of the compound. These “bound polymers” are essentially important for materials to have a great PTC intensity and good reproducibility. © 1994 John Wiley & Sons, Inc.     

Solvent free oxidation of alcohols catalyzed by KMnO4 adsorbed on Kieselguhr

Efficient and selective oxidation of primary and secondary alcohols to the corresponding aldehydes and ketones catalyzed by potassium permanganate supported on Kieselguhr reagent under solvent free conditions are reported.     

Effect of fiber volume fraction on longitudinal tensile properties of SiC<Subscript>f</Subscript>/Ti-6Al-4V composites

The longitudinal tensile properties of SiC_f/Ti-6Al-4V composites with different fiber volume fractions were simulated by the Monte Carlo 2-D finite element model. The random distribution of fiber strength was expressed by the two-parameter Weibull function. Meanwhile, contact elements and birth-death elements were used to describe the interfacial sliding process after debonding and fiber breakage (or matrix cracking) respectively, which was realized by subroutine complied in ANSYS-APDL (ANSYS Parametric Design Language). The experimental results show that the yield stress and ultimate tensile strength of SiC_f/Ti-6Al-4V composites increase with increasing fiber volume fraction, while the corresponding strain of them is just on the contrary. In addition, almost the same failure mode is obtained in SiC_f/Ti-6Al-4V composites with various fiber volume fractions when the interfacial shear strength is fixed. Finally, the tensile strength predicted by finite element analysis is compared with that predicted by Global load-sharing model, Local load-sharing model and conventional rule of mixtures, thus drawing the conclusion that Local load-sharing model is very perfect for the prediction of the ultimate tensile strength.