Graded evolution of anisotropic microstructure during sintering from crystal-oriented powder compact

Anisotropic sintering, including shrinkage and grain growth, was examined for c-axis-oriented (Sr,Ca)₂NaNb₅O₁₅ (SCNN) ceramics, which were prepared by colloidal processing under a magnetic field. In the c-axis-oriented SCNN powder compact, shrinkage and grain growth along the c-axis were higher than those along the a-axis. The anisotropic microstructural development was clearly associated with anisotropic sintering shrinkage. X-ray diffraction, scanning electron microscopy, and energy back scattering diffraction showed that the grain growth of oriented particles by including random grains contribute to the development of the oriented microstructure. Finally, the highly crystal-oriented SCNN ceramics with a densified microstructure were obtained through anisotropic sintering. These results clearly showed the potential to develop a well-defined anisotropic microstructure during sintering by designing and controlling the particle packing structure in a powder compact.     

刘家山排土场滑坡治理措施

刘家山排土场为民采排弃形成，已经出现大规模滑坡。为了保证上下游生产生活设施的安全，依据现场实际情况，结合现场调查，提出了削坡处理的方案。经过治理后，刘家山排土场平稳地渡过了雨季，目前处于稳定状态，达到了治理目的。     

数字化蓄热式钢包烘烤器及自动控制系统

蓄热式燃烧技术和脉冲燃烧技术是新型的节能环保燃烧技术。数字化蓄热式钢包烘烤器控制系统利用数字化脉冲控制把这两项技术结合在一起。这大大降低了能耗，减少环境污染。本文针对数字化蓄热式钢包烘烤器，提出升温阶段采用自寻优算法，不断调整换向时间，并能记忆最优参数，保证经过几次烘烤后系统整体最优；保温阶段即采用脉冲控制的方法。     

Synthesis of amphiphilic magnetic microspheres by dispersion copolymerization of styrene and poly(ethylene oxide) macromonomer

Amphiphilic magnetic microspheres ranging in diameter from 5 to 100 µm were prepared by dispersion copolymerization of styrene and poly(ethylene oxide) vinylbenzyl (PEO‐VB) macromonomer (MPEO) in the presence of Fe₃O₄ magnetic fluid. The effects of various polymerization parameters on the average particle size were systematically investigated. The average particle size was found to increase with increasing styrene concentration and initiator concentration. It also increased with decreasing stabilizer concentration and molecular weight of MPEO. The content of the hydroxyl groups localized in the microspheres ranged from 0.01 to 0.2 mmol g^?1. © 2003 Society of Chemical Industry     

石油化工生产火灾危险性分析

针对石油化工生产的特点,从物料特性、上艺装置、工艺控制参数、防火防爆安全装置、作业性质和消防安全设施等几方面综合分析其火灾危险性,并提出相应的防范措施,为消防安全评价提供依据。     

西气东输放空系统的设计与研究

论述了石油天然气行业中的放空系统工作原理，研究了西气东输采用的放空点火系统特点，讨论了放空立管的计算模型，提出了比较符合实际情况的计算模型，指出在桅杆结构的计算分析中，应该考虑钢丝绳的弹性支撑作用。钢丝绳的弹性支撑作用对结构的周期计算、风荷载导算、地震作用的计算都有较大的影响。     

现场总线漫谈

从现场总线多标准的现状出发，阐述了控制对象多样性与技术多样性之间的必然联系，通过对目前现场总线与传统DCS应用现状的分析，对现场总线的发展和应用前景进行了展望。     

6种金属材料在典型工业大气中的腐蚀规律

选取具有代表性的碳钢、不锈钢、镀锌碳钢、铝、钛和铜挂片,在某企业不同部位投放后进行为期半年的大气腐蚀试验,得出了在半年期中的腐蚀规律。在此基础上,对每种金属材料的腐蚀特点进行总结,并对大气腐蚀的各种影响因素进行分析,提出了行之有效的防护措施。     

含硫化氢气井钻井过程中的腐蚀因素与防护研究

在含硫气井的钻井过程中对于HRC大于22的钻具钢材除了腐蚀疲劳之外，在pH值小于9的环境中会发生硫化物应力腐蚀破裂，这种破坏比腐蚀疲劳更突然、更快，使钻杆大量损坏。含硫气井在钻井过程中，由于湿硫化氢的出现，常常会出现油管、套管、钻井设备、钻井仪器以及对支持保护管柱的水泥环柱等腐蚀和损坏问题，为此，阐述了湿硫化氢的腐蚀特点、机理，归纳总结了影响腐蚀的因素，综述了如何在这些方面防止其腐蚀，使损失减小，为指导油管、套管防腐工程实践提供了依据。建议在钻井过程中采用碱性钻井液，其pH值可到9或更高(至pH值12)，以减缓或防止钻井过程中电化学从硫化物应力腐蚀破裂；含硫气井用的钻杆应该间歇使用。钻杆停用堆置时间可使其放氢，使钻杆恢复韧性，防止硫化物应力腐蚀断裂。